Home › Engine / Hybrid System › 1GD-FTV LUBRICATION › OIL AND OIL FILTER › from 2016.01
RM3270E _51 Engine / Hybrid System _041677 1GD-FTV LUBRICATION _0207156 OIL AND OIL FILTER A

1GD-FTV LUBRICATION  OIL AND OIL FILTER  REPLACEMENT  


CAUTION / NOTICE / HINT

CAUTION:
·

Prolonged and repeated contact with engine oil will result in the removal of natural oils from the skin, leading to dryness, irritation and dermatitis. In addition, used engine oil contains potentially harmful contaminants which may cause skin cancer.

·

Precautions should be taken when replacing engine oil to minimize the risk of your skin making contact with used engine oil. Protective clothing and gloves that cannot be penetrated by oil should be worn. The skin should be washed with soap and water, or use waterless hand cleaner, to remove any used engine oil thoroughly. Do not use gasoline, thinners or solvents.

·

In order to protect the environment, used oil and used oil filters must be disposed of at designated disposal sites.

·
A339769

To prevent burns, do not remove the oil pan drain plug and oil filter sub-assembly while the engine is hot.



PROCEDURE

Hide 51410 1.REMOVE NO. 1 ENGINE UNDER COVER ASSEMBLY

Hide 51442 2.REMOVE NO. 2 ENGINE UNDER COVER ASSEMBLY

Hide 3.DRAIN ENGINE OIL

CAUTION:

To prevent burns, do not remove the oil pan drain plug while the engine is hot.


a.

Remove the oil filler cap assembly.


b.

Remove the oil pan drain plug and gasket, and then drain the engine oil into a container.


c.

Clean and install a new gasket and the oil pan drain plug.

Torque:
40 N*m (408 kgf*cm, 30 ft.*lbf)


Hide 15601 4.REMOVE OIL FILTER SUB-ASSEMBLY

CAUTION:

To prevent burns, do not remove the oil filter sub-assembly while the engine is hot.


a.
A388333N01
0.885,0.896 1.271,0.896 true 0.594,0.813 0.917,0.99 0.323,0.177 10 true SST

Using SST, remove the oil filter sub-assembly.

SST
09228-07501  

HINT:
·

Before removing the oil filter sub-assembly, place cloth where the oil may splash.

·

Use a container to catch the draining engine oil.




Hide 15601 5.INSTALL OIL FILTER SUB-ASSEMBLY

a.

Check and clean the oil filter sub-assembly installation surface.


b.

Apply clean engine oil to the gasket of a new oil filter sub-assembly.


c.

Lightly screw the oil filter sub-assembly into place by hand. Tighten it until the gasket contacts the seat.


d.

Using SST, tighten the oil filter sub-assembly.

SST
09228-07501  

A388334C01
3.792,1.25 4.219,1.25 true 3.479,1.177 3.802,1.354 0.323,0.177 10 true SST
V100135

3/4 Turn - -


i.

Depending on the space available, choose from the following.

If enough space is available, use a torque wrench to tighten the oil filter sub-assembly.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)


ii.

If enough space is not available to use a torque wrench, tighten the oil filter sub-assembly 3/4 of a turn by hand or with a common wrench.



Hide 6.ADD ENGINE OIL

a.

Add new engine oil and install the oil filler cap assembly.

Standard Oil Grade:
Item Oil Grade Oil Viscosity (SAE)
w/ DPF ACEA C2
(Using engine oil other than ACEA C2 may damage the catalytic converter)
- 0W-30
- 5W-30
w/o DPF API-CF-4, CF or ACEA B1 - 5W-30
- 10W-30
- 15W-40


Standard Capacity:
Item Specified Condition
Drain and refill without oil filter sub-assembly change 7.0 liters (7.4 US qts, 6.2 Imp. qts)
Drain and refill with oil filter sub-assembly change 7.5 liters (7.9 US qts, 6.6 Imp. qts)
Dry fill 8.0 liters (8.5 US qts, 7.0 Imp. qts)



Hide 7.INSPECT FOR OIL LEAK

a.

Start the engine. Make sure that there are no oil leaks from the areas that were worked on.


Hide 51442 9.INSTALL NO. 2 ENGINE UNDER COVER ASSEMBLY

Hide 51410 10.INSTALL NO. 1 ENGINE UNDER COVER ASSEMBLY