Home › Drivetrain › DRIVE SHAFT / PROPELLER SHAFT › PROPELLER SHAFT ASSEMBLY(for TMMIN Made) › from 2016.01
RM3270E _52 Drivetrain _041685 DRIVE SHAFT / PROPELLER SHAFT _0245185 PROPELLER SHAFT ASSEMBLY(for TMMIN Made) A

DRIVE SHAFT / PROPELLER SHAFT  PROPELLER SHAFT ASSEMBLY(for TMMIN Made)  DISASSEMBLY  


CAUTION / NOTICE / HINT

NOTICE:
·

When using a vise, place aluminum plates between the part and vise.

·

When using a vise, do not overtighten it.



PROCEDURE

Hide 42345A 1.REMOVE REAR PROPELLER SHAFT BOOT CLAMP (for 4WD)

a.
C330835C01
1.25,0.938 1.833,0.938 true 2.26,1.229 2.844,1.229 true 1.729,0.615 2.313,0.615 true 2.75,3.5 2.75,4.083 2.75,4.083 2.917,4.083 true 2.917,2.583 2.75,2.583 2.75,2.583 2.75,3.167 true 2.917,2.583 1.083,2.583 1.083,2.583 1.083,3.167 true 1,3.5 1,4.5 1,4.5 1.167,4.5 true 1.833,3.917 1.833,3.833 1.833,3.833 2.417,3.833 true 3,2.469 3.313,2.667 0.313,0.198 10 false *a 1.521,0.552 1.833,0.75 0.313,0.198 10 false *1 1.031,0.865 1.344,1.063 0.313,0.198 10 false *1 2.948,1.135 3.26,1.333 0.313,0.198 10 false *2 1.208,4.417 1.521,4.615 0.313,0.198 10 false *b 2.948,4 3.26,4.198 0.313,0.198 10 false *b 2.469,3.75 2.781,3.948 0.313,0.198 10 false *c
*1 Propeller Shaft Boot Clamp
*2 Rear Sliding Shaft Boot
*a Matchmark of Propeller Shaft and Sleeve Yoke
*b Matchmark of Pinching Portion of Propeller Shaft Boot Clamp
*c Pinching Portion


Place matchmarks on the propeller shaft and sleeve yoke.


b.

Apply matchmarks at the pinching portions of the propeller shaft boot clamps of the propeller shaft and sleeve yoke.

HINT:
·

Make sure to place matchmarks to clearly identify the location of the pinching portions of the propeller shaft boot clamps.

If the pinching portions are installed at different locations than where they were located before disassembly, the rotational balance of the propeller shaft cannot be ensured, which may result in vibrations and noise.

·

Make sure that the matchmarks are different enough so that they cannot be confused with each other.

·

The location of the pinching portions may differ from the location shown in the illustration, so make sure to confirm and properly place matchmarks according to the vehicle.




c.

Using a side cutter or pliers, disconnect the 2 propeller shaft boot clamps.


d.

Disconnect the 2 propeller shaft boot clamps from the sleeve yoke.


e.

Remove the sleeve yoke, and then remove the rear sliding shaft boot and 2 propeller shaft boot clamps from the propeller shaft.


Hide 2.REMOVE SPIDER BEARING

HINT:

Use the same procedure for all spiders.


a.
C330810C01
1.635,0.99 1.01,0.479 1.01,0.479 1.927,0.74 true 0.771,0.375 1.083,0.573 0.313,0.198 10 false *a
*a Matchmark


Place matchmarks on the flange yoke and propeller shaft.


b.

for Pre-Runner:

i.
C330880C01
2.115,0.833 2.813,0.208 2.813,0.208 2.563,0.896 true 2.865,0.115 3.177,0.313 0.313,0.198 10 false *a
*a Matchmark


w/ flange coupling:

Place matchmarks on the propeller shaft and flange yoke.


ii.
C330807C01
1.688,0.792 2.833,1.49 2.833,1.49 1.854,0.635 true 2.938,1.448 3.25,1.646 0.313,0.198 10 false *a
*a Matchmark


w/o flange coupling:

Place matchmarks on the center yoke and sleeve yoke.


iii.
C330806C01
1.448,1.49 2.542,1.885 2.542,1.885 1.531,1.25 true 2.625,1.823 2.938,2.021 0.313,0.198 10 false *a
*a Matchmark


Place matchmarks on the sleeve yoke and intermediate shaft.



c.

for 4WD:

i.
C330880C01
2.115,0.833 2.813,0.208 2.813,0.208 2.563,0.896 true 2.865,0.115 3.177,0.313 0.313,0.198 10 false *a
*a Matchmark


w/ flange coupling:

Place matchmarks on the propeller shaft and flange yoke.


ii.
C330805C01
1.625,0.844 2.698,1.25 2.698,1.25 1.771,0.656 true 2.75,1.177 3.063,1.375 0.313,0.198 10 false *a
*a Matchmark


w/o flange coupling:

Place matchmarks on the center yoke and sleeve yoke.


iii.
C330804C01
1.708,1.51 2.531,1.708 2.531,1.708 1.896,1.354 true 2.615,1.625 2.927,1.823 0.313,0.198 10 false *a
*a Matchmark


Place matchmarks on the flange yoke and intermediate shaft.



d.
C061264

Using a brass bar and hammer, slightly tap in the spider bearing outer races.


e.

Using 2 screwdrivers, remove the 4 snap rings from the grooves.


f.
C317895C01
0.833,1.167 1.167,1.167 true 2.625,1.25 3.063,1.25 true 1.708,0.635 2.021,0.833 0.313,0.198 10 false *a 0.625,0.656 0.938,0.854 0.313,0.198 10 false *b 0.5,1.083 0.833,1.281 0.333,0.198 10 true SST 3.146,1.167 3.302,1.396 0.156,0.229 10 true A
*a Turn
*b Hold


Using SST, push out the spider bearing from the propeller shaft assembly.

SST
09332-25010  

HINT:

Before installing SST, sufficiently raise the part labeled A. If the part labeled A is too low, it may be difficult to install SST.



g.
C307729C01
2.719,1.146 2.313,0.719 true 2.771,1.104 3.083,1.302 0.313,0.198 10 false *a
*a Hammering Point


Tap off the propeller shaft to remove the spider bearing.

NOTICE:

Do not tap the shaft.


HINT:

Remove the spider bearing on the opposite side using the same procedure.



h.

Remove the flange yoke from the propeller shaft.


i.
C307746C01
2.125,1.146 2.5,1.146 true 0.573,1.188 0.948,1.188 true 1.656,0.604 1.969,0.802 0.313,0.198 10 false *a 0.438,0.177 0.781,0.385 0.344,0.208 10 false *b 1.948,1.083 2.156,1.313 0.208,0.229 10 false A 0.26,1.115 0.656,1.313 0.396,0.198 10 false SST
*a Turn
*b Hold


Install the 2 removed spider bearing outer races to the spider.


j.

Using SST, push out the spider bearing from the flange yoke.

SST
09332-25010  

HINT:

Before installing SST, sufficiently raise the part labeled A. If the part labeled A is too low, it may be difficult to install SST.



k.
C258224C01
1.396,0.313 1.823,0.313 1.823,0.313 2.417,0.604 true 1.188,0.219 1.406,0.417 0.219,0.198 10 *a
*a Hammering Point


Tap off the spider bearing with a hammer.


l.

Remove the spider.


Hide 37230 3.REMOVE CENTER NO. 1 SUPPORT BEARING ASSEMBLY (for Pre-Runner)

a.

w/ flange coupling:

i.
C330852C01
1.625,0.854 2.479,0.271 2.479,0.271 1.521,0.792 true 2.542,0.177 3,0.375 0.458,0.198 10 false *a
*a Matchmark


Place matchmarks on the flange coupling and flange yoke.


ii.

Remove the 4 nuts and 4 washers.


iii.

Disconnect the propeller shaft and intermediate shaft.


iv.
C330851

Using a chisel and hammer, loosen the staked part of the lock nut.

NOTICE:
·

Completely loosen the staked part of the lock nut when removing it.

·

Do not damage the threads of the intermediate shaft.




v.
C346179C02
2.5,1 2.5,1.667 2.5,1.667 2.667,1.667 true 1.313,0.531 1.625,0.729 0.313,0.198 10 false *a 1.646,1.604 1.958,1.802 0.313,0.198 10 false *b 2.729,1.583 3.188,1.781 0.458,0.198 10 false SST
*a Turn
*b Hold


Using SST and a socket wrench, remove the lock nut.

SST
09330-00021  


vi.
C330854C01
1.75,1.083 2.917,1.083 true 1.75,1.417 2.323,1.427 2.323,1.427 2.333,1.083 true 3.01,0.979 3.323,1.177 0.313,0.198 10 false *a
*a Matchmark


Place matchmarks on the intermediate shaft and flange coupling.


vii.
C330853C02
2,0.417 2.167,0.167 2.167,0.167 2.333,0.167 true 2.417,0.094 2.875,0.292 0.458,0.198 10 false SST 1.188,1.792 1.5,1.948 0.313,0.156 10 false *a 0.406,1.188 0.719,1.344 0.313,0.156 10 false *b
*a Turn
*b Hold


Using SST, remove the flange coupling and 2 washers from the intermediate shaft.

SST
09950-30012  (09951-03010, 09953-03010, 09954-03010, 09955-03030, 09956-03030)


viii.

Remove the center No. 1 support bearing assembly.



b.

w/o flange coupling:

i.
C118616

Using a hammer and chisel, loosen the staked part of the lock nut and remove the lock nut.

NOTICE:
·

Completely loosen the staked part of the lock nut when removing it.

·

Do not damage the threads of the intermediate shaft.




ii.
C118617C07
1.74,1.115 1.74,0.521 1.74,0.521 2.698,0.521 true 1.76,1.25 2.115,1.25 2.115,1.25 2.115,0.542 true 2.76,0.448 3.01,0.625 0.25,0.177 10 false *a
*a Matchmark


Place matchmarks on the intermediate shaft and center yoke.


iii.

Using a brass bar and hammer, tap out the center yoke.


iv.

Remove the 2 washers and center No. 1 support bearing assembly from the intermediate shaft.



Hide 37230 4.REMOVE CENTER NO. 1 SUPPORT BEARING ASSEMBLY (for 4WD)

a.

w/ flange coupling:

i.
C330852C01
1.625,0.854 2.479,0.271 2.479,0.271 1.521,0.792 true 2.542,0.177 3,0.375 0.458,0.198 10 false *a
*a Matchmark


Place matchmarks on the flange coupling and flange yoke.


ii.

Remove the 4 nuts and 4 washers.


iii.

Disconnect the propeller shaft and intermediate shaft.


iv.
C330851

Using a chisel and hammer, loosen the staked part of the lock nut.

NOTICE:
·

Completely loosen the staked part of the lock nut when removing it.

·

Do not damage the threads of the intermediate shaft.




v.
C346179C02
2.5,1 2.5,1.667 2.5,1.667 2.667,1.667 true 1.313,0.531 1.625,0.729 0.313,0.198 10 false *a 1.646,1.604 1.958,1.802 0.313,0.198 10 false *b 2.729,1.583 3.188,1.781 0.458,0.198 10 false SST
*a Turn
*b Hold


Using SST and a socket wrench, remove the lock nut.

SST
09330-00021  


vi.
C330854C01
1.75,1.083 2.917,1.083 true 1.75,1.417 2.323,1.427 2.323,1.427 2.333,1.083 true 3.01,0.979 3.323,1.177 0.313,0.198 10 false *a
*a Matchmark


Place matchmarks on the intermediate shaft and flange coupling.


vii.
C330853C02
2,0.417 2.167,0.167 2.167,0.167 2.333,0.167 true 2.417,0.094 2.875,0.292 0.458,0.198 10 false SST 1.188,1.792 1.5,1.948 0.313,0.156 10 false *a 0.406,1.188 0.719,1.344 0.313,0.156 10 false *b
*a Turn
*b Hold


Using SST, remove the flange coupling and 2 washers from the intermediate shaft.

SST
09950-30012  (09951-03010, 09953-03010, 09954-03010, 09955-03030, 09956-03030)


viii.

Remove the center No. 1 support bearing assembly.



b.

w/o flange coupling:

i.
C118616

Using a hammer and chisel, loosen the staked part of the lock nut and remove the lock nut.

NOTICE:
·

Completely loosen the staked part of the lock nut when removing it.

·

Do not damage the threads of the intermediate shaft.




ii.
C118617C07
1.74,1.115 1.74,0.521 1.74,0.521 2.698,0.521 true 1.76,1.25 2.115,1.25 2.115,1.25 2.115,0.542 true 2.76,0.448 3.01,0.625 0.25,0.177 10 false *a
*a Matchmark


Place matchmarks on the intermediate shaft and center yoke.


iii.

Using a brass bar and hammer, tap out the center yoke.


iv.

Remove the 2 washers and center No. 1 support bearing assembly from the intermediate shaft.