Home › Drivetrain › DRIVE SHAFT / PROPELLER SHAFT › PROPELLER SHAFT ASSEMBLY(for TMT Made) › from 2016.01
RM3270E _52 Drivetrain _041685 DRIVE SHAFT / PROPELLER SHAFT _0217831 PROPELLER SHAFT ASSEMBLY(for TMT Made) A

DRIVE SHAFT / PROPELLER SHAFT  PROPELLER SHAFT ASSEMBLY(for TMT Made)  REMOVAL  


PROCEDURE

Hide 51569 1.REMOVE PROPELLER SHAFT GUARD

a.

for Pre-Runner:

i.
C317873

for Transmission side:

Remove the 2 bolts and propeller shaft guard.


ii.
C317875

for Center support bearing side:

Remove the 2 bolts and propeller shaft guard.



b.

for 4WD:

i.
C317869

for Transfer side:

Remove the 2 bolts and propeller shaft guard.


ii.
C317870

for Center support bearing side:

Remove the 2 bolts and propeller shaft guard.



Hide 37100 2.REMOVE PROPELLER SHAFT WITH CENTER BEARING ASSEMBLY (for Pre-Runner)

a.
C317864C01
1.573,1.469 2.188,1.854 2.188,1.854 1.573,1.385 true 2.281,1.792 2.594,1.99 0.313,0.198 10 true *a
*a Matchmark


Place matchmarks on the propeller shaft flange and differential flange.


b.
C317880C01
1.656,4.021 2.531,4.177 2.531,4.177 1.667,3.938 true 1.75,1.479 2.438,1.906 2.438,1.906 1.75,1.594 true 2.583,4.104 2.896,4.302 0.313,0.198 10 true *a 2.521,1.844 2.833,2.042 0.313,0.198 10 true *a
*a Matchmark


for 2GD-FTV (RC60):

Place matchmarks on the propeller shaft flange, differential torsional damper and differential flange.


c.
C354037C01
1.833,1.552 2.375,2.073 2.375,2.073 1.823,1.49 true 2.031,3.781 2.573,4.302 2.573,4.302 2.021,3.719 true 2.417,1.969 2.792,2.208 0.375,0.24 10 true *a 2.646,4.292 3.021,4.531 0.375,0.24 10 true *a
*a Matchmark


for 1GR-FE (AC60E):

Place matchmarks on the propeller shaft flange, differential mass damper and differential flange.


d.

Remove the 4 nuts and 4 washers and disconnect the propeller shaft with center bearing assembly.


e.
C317877

Remove the 2 set bolts of the center support bearing from the frame crossmember.


f.

Pull out the propeller shaft with center bearing assembly.

NOTICE:

When pulling out the propeller shaft with center bearing assembly, make sure that transmission fluid does not leak from the extension housing.


HINT:

Transmission fluid may leak from the extension housing therefore, use a container to catch the fluid.



g.
C317881

for 2GD-FTV (RC60):

Remove the differential torsional damper.


h.
C354036

for 1GR-FE (AC60E):

Remove the differential mass damper.


Hide 37100 3.REMOVE PROPELLER SHAFT WITH CENTER BEARING ASSEMBLY (for 4WD)

a.
C317863C01
1.615,1.469 2.146,1.979 2.146,1.979 1.646,1.365 true 2.208,1.906 2.521,2.104 0.313,0.198 10 true *a
*a Matchmark


Place matchmarks on the propeller shaft flange and transfer flange.


b.

Remove the 4 nuts and 4 washers and disconnect the propeller shaft.


c.
C317864C01
1.573,1.469 2.188,1.854 2.188,1.854 1.573,1.385 true 2.281,1.792 2.594,1.99 0.313,0.198 10 true *a
*a Matchmark


Place matchmarks on the propeller shaft flange and differential flange.


d.
C354037C01
1.833,1.552 2.375,2.073 2.375,2.073 1.823,1.49 true 2.031,3.781 2.573,4.302 2.573,4.302 2.021,3.719 true 2.417,1.969 2.792,2.208 0.375,0.24 10 true *a 2.646,4.292 3.021,4.531 0.375,0.24 10 true *a
*a Matchmark


for 1GR-FE (AC60F):

Place matchmarks on the propeller shaft flange, differential mass damper and differential flange.


e.

Remove the 4 nuts and 4 washers.


f.
C317877

Remove the 2 set bolts of the center No. 1 support bearing assembly from the frame crossmember.


g.

Remove the propeller shaft with center bearing assembly.


h.
C317881

for 1GR-FE (AC60F):

Remove the differential mass damper.