Home › Drivetrain › AC60E AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSMISSION SYSTEM(for 1GD-FTV) › from 2016.01
RM3270E _52 Drivetrain _048959 AC60E AUTOMATIC TRANSMISSION / TRANSAXLE _0245465 AUTOMATIC TRANSMISSION SYSTEM(for 1GD-FTV) J

AC60E AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM(for 1GD-FTV)  Pattern Select Switch Power Mode Circuit  


DESCRIPTION

The ECM memory contains the programs for the normal and PWR shift patterns.

By following the programs corresponding to the signals from the combination switch assembly (pattern select switch), park/neutral position switch and other various sensors, the ECM switches the shift solenoid valves on and off, and controls the transmission gear ratio.

WIRING DIAGRAM

C326150E10
6.302,1.083 6.823,1.281 0.521,0.198 10 false 12 V 5.823,2.958 6.156,3.156 0.333,0.198 10 false G49 5.823,3.125 6.177,3.323 0.354,0.198 10 false ECM 5.167,1.25 5.385,1.448 0.219,0.198 10 false 12 3.906,1.271 4.063,1.469 0.156,0.198 10 false 3 3.479,1.25 3.938,1.448 0.458,0.198 10 false PWR 2.531,1.24 2.688,1.438 0.156,0.198 10 false E 2.323,1.26 2.479,1.458 0.156,0.198 10 false 2 5.479,1.26 6.094,1.458 0.615,0.198 10 false PWMS 2.281,2.094 4.188,2.531 1.906,0.438 10 false Combination Switch Assembly (Pattern Select Switch) 2.292,1.948 3.333,2.146 1.042,0.198 10 false I5

PROCEDURE

1.INSPECT COMBINATION SWITCH ASSEMBLY (PATTERN SELECT SWITCH)
a.
C324163C05
1.333,1.708 1.958,1.281 false 2.365,1.708 2.135,1.271 false 0.063,0.063 0.375,0.26 0.313,0.198 10 false *1 1.063,1.75 1.667,1.948 0.604,0.198 10 false 3 (PWR) 2.281,1.76 2.688,1.948 0.406,0.188 10 false 2 (E)
*1 Combination Switch Assembly (Pattern Select Switch)


Remove the combination switch assembly (pattern select switch).

Click hereDrivetrain>AC60E AUTOMATIC TRANSMISSION / TRANSAXLE>PATTERN SELECT SWITCH>REMOVAL


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
3 (PWR) - 2 (E) Combination switch (PWR) pushed Below 1 Ω
3 (PWR) - 2 (E) Combination switch (PWR) not pushed 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (COMBINATION SWITCH - BODY GROUND)

NG

REPLACE COMBINATION SWITCH ASSEMBLY (PATTERN SELECT SWITCH)

2.CHECK HARNESS AND CONNECTOR (COMBINATION SWITCH - BODY GROUND)
a.
C323648C03
0.177,0.885 0.573,1.146 0.396,0.26 1.031,1.771 1.281,1.354 true 0.958,1.792 1.115,1.99 0.156,0.198 10 false E 0.323,0.938 0.583,1.135 0.26,0.198 10 false I5 0.063,0.063 0.365,0.271 0.302,0.208 10 false *a
*a Front view of wire harness connector
(to Combination Switch Assembly (Pattern Select Switch))


Disconnect the combination switch assembly (pattern select switch) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I5-2 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (COMBINATION SWITCH - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (COMBINATION SWITCH - ECM)
a.
C318001C06
2.229,0.26 2.583,0.5 0.354,0.24 1.927,2.771 2.354,1.906 true 1.677,2.823 2.76,3.063 1.083,0.24 10 false 12 (PWMS) 2.281,0.323 2.604,0.49 0.323,0.167 10 false G49 0.125,0.115 0.448,0.281 0.323,0.167 10 false *a
*a Rear view of wire harness connector
(to ECM)


Disconnect the ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G49-12 (PWMS) - Body ground Combination switch (PWR) pushed Below 1 Ω
G49-12 (PWMS) - Body ground Combination switch (PWR) not pushed 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR