Home › Drivetrain › AC60E AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSMISSION SYSTEM(for 1GD-FTV) › from 2016.01
RM3270E _52 Drivetrain _048959 AC60E AUTOMATIC TRANSMISSION / TRANSAXLE _0245465 AUTOMATIC TRANSMISSION SYSTEM(for 1GD-FTV) C

AC60E AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM(for 1GD-FTV)  P2716  Pressure Control Solenoid "D" Electrical (Shift Solenoid Valve SLT)  


DESCRIPTION

The shift solenoid valve SLT controls the transmission line pressure for smooth transmission operation based on signals from the throttle position sensor and the vehicle speed sensor. The ECM adjusts the current to shift solenoid valve SLT to control hydraulic line pressure coming from the primary regulator valve. Appropriate line pressure assures smooth shifting with varying engine outputs.

C318298E01
1.573,0.208 1.802,0.208 1.802,0.208 2.281,0.771 true 1.604,1.313 1.833,1.313 1.833,1.313 2.198,0.938 true 3.604,0.26 3.323,0.26 3.323,0.26 3.219,0.635 true 1.146,1.219 2.063,1.417 0.917,0.198 10 false Sleeve 0.813,0.125 2.5,0.323 1.688,0.198 10 false Spool Valve 3.677,0.188 4.906,0.385 1.229,0.198 10 false Solenoid 4.479,0.635 5.073,1.031 0.594,0.396 10 false Hydraulic Pressure 5.698,1.438 6.771,1.635 1.073,0.198 10 false Current

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P2716 Pressure Control Solenoid "D" Electrical (Shift Solenoid Valve SLT) Open or short is detected in shift solenoid valve SLT circuit for 1 second or more while driving (1 trip detection logic).
·

Open or short in shift solenoid valve SLT circuit

·

Shift solenoid valve SLT

·

ECM


- DTC stored

MONITOR DESCRIPTION

When an open or short in the shift solenoid valve SLT circuit is detected, the ECM interprets this as a fault. The ECM will store the DTC.

WIRING DIAGRAM

C311453E20
1.49,1.729 5.156,1.927 3.667,0.198 10 false Shift Solenoid Valve SLT 5.167,1.135 5.781,1.333 0.615,0.198 10 false SLT+ 5.167,2.125 5.781,2.323 0.615,0.198 10 false SLT- 4.917,2.125 5.531,2.323 0.615,0.198 10 false 15 4.917,1.135 5.531,1.333 0.615,0.198 10 false 14 3.885,1.146 4.5,1.344 0.615,0.198 10 false 13 3.896,2.115 4.51,2.313 0.615,0.198 10 false 14 1.26,1.344 1.875,1.542 0.615,0.198 10 false 1 1.271,2.125 1.885,2.323 0.615,0.198 10 false 2 3.469,1.146 4.083,1.344 0.615,0.198 10 false SLT+ 3.479,2.125 4.094,2.323 0.615,0.198 10 false SLT- 5.75,0.781 6.365,0.979 0.615,0.198 10 false 12 V 1.813,2.719 2.271,2.917 0.458,0.198 10 false C31 1.813,2.906 4.417,3.104 2.604,0.198 10 false Transmission Wire 5.573,3.021 5.885,3.219 0.313,0.198 10 false C41 5.573,3.198 6.031,3.396 0.458,0.198 10 false ECM

CAUTION / NOTICE / HINT

NOTICE:

Perform registration and/or initialization when parts related to the automatic transmission are replaced.

Click hereDrivetrain>AC60E AUTOMATIC TRANSMISSION / TRANSAXLE>AUTOMATIC TRANSMISSION SYSTEM(for 1GD-FTV)>INITIALIZATION


HINT:

After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.



PROCEDURE

1.INSPECT TRANSMISSION WIRE (SHIFT SOLENOID VALVE SLT)
a.
C319326C06
1.854,1.667 1.969,1.177 true 2.448,1.74 2.188,1.177 true 0.156,0.104 0.469,0.302 0.313,0.198 10 false *a 1.677,1.729 2.146,1.927 0.469,0.198 10 false SLT- 2.281,1.813 2.698,2 0.417,0.188 10 false SLT+
*a Component without harness connected
(Transmission Wire)


Disconnect the transmission wire connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
13 (SLT+) - 14 (SLT-) 20°C (68°F) 5.0 to 5.6 Ω
13 (SLT+) - Body ground Always 10 kΩ or higher
14 (SLT-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - ECM)

NG

3.INSPECT SHIFT SOLENOID VALVE SLT
2.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - ECM)
a.
C318003C06
1.781,0.281 2.135,0.5 0.354,0.219 0.958,2.313 1.729,1.896 true 1.479,2.604 1.802,1.906 true 1.844,0.323 2.156,0.521 0.313,0.198 10 false C41 1.208,2.688 1.875,2.865 0.667,0.177 10 false 14 (SLT+) 0.094,0.104 0.406,0.302 0.313,0.198 10 false *a 0.667,2.354 1.333,2.531 0.667,0.177 10 false 15 (SLT-)
*a Rear view of wire harness connector
(to ECM)


Disconnect the ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C41-14 (SLT+) - C41-15 (SLT-) 20°C (68°F) 5.0 to 5.6 Ω
C41-14 (SLT+) - Body ground Always 10 kΩ or higher
C41-15 (SLT-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT SHIFT SOLENOID VALVE SLT
a.
C201747C15
1.49,0.875 0.635,0.646 false 1.781,0.865 2.479,0.625 false 1.49,3.125 0.635,2.896 false 1.781,3.125 2.479,2.885 false 2.542,0.552 2.719,0.75 0.177,0.198 10 false 1 0.51,0.563 0.688,0.76 0.177,0.198 10 false 2 1.177,4.198 1.385,4.406 0.208,0.208 10 false (-) 1.917,4.208 2.146,4.406 0.229,0.198 10 false (+) 2.563,2.792 2.74,2.99 0.177,0.198 10 false 1 0.49,2.813 0.667,3.01 0.177,0.198 10 false 2 0.135,0.135 0.354,0.344 0.219,0.208 10 false *1
*1 Shift Solenoid Valve SLT


Remove shift solenoid valve SLT.

Click hereDrivetrain>AC60E AUTOMATIC TRANSMISSION / TRANSAXLE>VALVE BODY ASSEMBLY>DISASSEMBLY


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 20°C (68°F) 5.0 to 5.6 Ω



c.

Apply 12 V battery voltage to the shift solenoid valve and check that the valve moves and makes an operating noise.

OK:
Measurement Condition Specified Condition
·

Battery positive (+) with a 21 W bulb → Terminal 1

·

Battery negative (-) → Terminal 2


Valve moves and makes an operating noise



Result:
Proceed to
OK
NG



OK

NG