Home › Drivetrain › AC60E AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSMISSION SYSTEM(for 1GD-FTV) › from 2016.01
RM3270E _52 Drivetrain _048959 AC60E AUTOMATIC TRANSMISSION / TRANSAXLE _0245465 AUTOMATIC TRANSMISSION SYSTEM(for 1GD-FTV) C

AC60E AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM(for 1GD-FTV)  P2759  Torque Converter Clutch Pressure Control Solenoid Control Circuit Electrical (Shift Solenoid Valve SLU)  


DESCRIPTION

The ECM uses the signals from the throttle position sensor, air-flow meter, input turbine speed sensor, output shaft speed sensor and crankshaft position sensor to monitor the engagement condition of the lock-up clutch.

C318299E01
1.656,0.292 1.854,0.292 1.854,0.292 2.229,0.771 true 1.656,1.25 1.854,1.25 1.854,1.25 2.292,0.938 true 3.771,0.292 3.583,0.292 3.583,0.292 3.271,0.771 true 0.885,0.208 2.573,0.406 1.688,0.198 10 false Spool Valve 1.208,1.156 2.125,1.354 0.917,0.198 10 false Sleeve 3.833,0.219 5.063,0.417 1.229,0.198 10 false Solenoid 4.51,0.615 5.104,1.052 0.594,0.438 10 false Hydraulic Pressure 5.823,1.438 6.896,1.635 1.073,0.198 10 false Current

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P2759 Torque Converter Clutch Pressure Control Solenoid Control Circuit Electrical (Shift Solenoid Valve SLU) Open or short is detected in shift solenoid valve SLU circuit for 1 second or more while driving (1 trip detection logic).
·

Open or short in shift solenoid valve SLU circuit

·

Shift solenoid valve SLU

·

ECM


- DTC stored

MONITOR DESCRIPTION

When an open or short in a shift solenoid valve SLU circuit is detected, the ECM determines there is a malfunction. The ECM will store this DTC.

WIRING DIAGRAM

C311453E21
1.49,1.729 5.156,1.927 3.667,0.198 10 false Shift Solenoid Valve SLU 5.167,1.135 5.781,1.333 0.615,0.198 10 false SLU+ 5.167,2.115 5.781,2.313 0.615,0.198 10 false SLU- 4.969,2.115 5.583,2.313 0.615,0.198 10 false 9 4.969,1.135 5.583,1.333 0.615,0.198 10 false 8 3.906,1.135 4.521,1.333 0.615,0.198 10 false 21 3.906,2.115 4.521,2.313 0.615,0.198 10 false 22 1.292,2.115 1.906,2.313 0.615,0.198 10 false 2 1.281,1.344 1.896,1.542 0.615,0.198 10 false 1 3.438,1.135 4.052,1.333 0.615,0.198 10 false SLU+ 3.448,2.115 4.063,2.313 0.615,0.198 10 false SLU- 5.75,0.781 6.365,0.979 0.615,0.198 10 false 12 V 1.813,2.719 2.271,2.917 0.458,0.198 10 false C31 1.823,2.885 4.427,3.083 2.604,0.198 10 false Transmission Wire 5.573,3.021 5.885,3.219 0.313,0.198 10 false C39 5.573,3.198 6.031,3.396 0.458,0.198 10 false ECM

CAUTION / NOTICE / HINT

NOTICE:

Perform registration and/or initialization when parts related to the automatic transmission are replaced.

Click hereDrivetrain>AC60E AUTOMATIC TRANSMISSION / TRANSAXLE>AUTOMATIC TRANSMISSION SYSTEM(for 1GD-FTV)>INITIALIZATION


HINT:

After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.



PROCEDURE

1.INSPECT TRANSMISSION WIRE (SHIFT SOLENOID VALVE SLU)
a.
C319326C08
2.104,1.75 2.281,1.375 true 2.635,1.781 2.438,1.375 true 0.156,0.104 0.469,0.302 0.313,0.198 10 false *a 1.958,1.792 2.427,1.99 0.469,0.198 10 false SLU- 2.531,1.823 3,2.083 0.469,0.26 10 false SLU+
*a Component without harness connected
(Transmission Wire)


Disconnect the transmission wire connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
21 (SLU+) - 22 (SLU-) 20°C (68°F) 5.0 to 5.6 Ω
21 (SLU+) - Body ground Always 10 kΩ or higher
22 (SLU-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - ECM)

NG

3.INSPECT SHIFT SOLENOID VALVE SLU
2.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - ECM)
a.
C325304C03
0.875,0.333 1.271,0.573 0.396,0.24 1.417,1.896 2.01,2.875 true 1.354,1.896 0.677,2.854 true 0.083,0.104 0.396,0.26 0.313,0.156 10 false *a 1.76,2.938 2.49,3.156 0.729,0.219 10 false 8 (SLU+) 0.948,0.375 1.677,0.594 0.729,0.219 10 false C39 0.406,2.906 1.135,3.125 0.729,0.219 10 false 9 (SLU-)
*a Rear view of wire harness connector
(to ECM)


Disconnect the ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C39-8 (SLU+) - C39-9 (SLU-) 20°C (68°F) 5.0 to 5.6 Ω
C39-8 (SLU+) - Body ground Always 10 kΩ or higher
C39-9 (SLU-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT SHIFT SOLENOID VALVE SLU
a.
C201747C15
1.49,0.875 0.635,0.646 false 1.781,0.865 2.479,0.625 false 1.49,3.125 0.635,2.896 false 1.781,3.125 2.479,2.885 false 2.542,0.552 2.719,0.75 0.177,0.198 10 false 1 0.51,0.563 0.688,0.76 0.177,0.198 10 false 2 1.177,4.198 1.385,4.406 0.208,0.208 10 false (-) 1.917,4.208 2.146,4.406 0.229,0.198 10 false (+) 2.563,2.792 2.74,2.99 0.177,0.198 10 false 1 0.49,2.813 0.667,3.01 0.177,0.198 10 false 2 0.135,0.135 0.354,0.344 0.219,0.208 10 false *1
*1 Shift Solenoid Valve SLU


Remove shift solenoid valve SLU.

Click hereDrivetrain>AC60E AUTOMATIC TRANSMISSION / TRANSAXLE>VALVE BODY ASSEMBLY>DISASSEMBLY


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 20°C (68°F) 5.0 to 5.6 Ω



c.

Apply 12 V battery voltage to the shift solenoid valve and check that the valve moves and makes an operating noise.

OK:
Measurement Condition Specified Condition
·

Battery positive (+) with a 21 W bulb → Terminal 1

·

Battery negative (-) → Terminal 2


Valve moves and makes an operating noise



Result:
Proceed to
OK
NG



OK

NG