Home › Drivetrain › AC60E AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSMISSION SYSTEM(for 1GD-FTV) › from 2016.01
RM3270E _52 Drivetrain _048959 AC60E AUTOMATIC TRANSMISSION / TRANSAXLE _0245465 AUTOMATIC TRANSMISSION SYSTEM(for 1GD-FTV) C

AC60E AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM(for 1GD-FTV)  P2769  Short in Torque Converter Clutch Solenoid Circuit (Shift Solenoid Valve SL)  P2770  Open in Torque Converter Clutch Solenoid Circuit (Shift Solenoid Valve SL)  


DESCRIPTION

Shift solenoid valve SL is turned on and off by signals from the ECM to control the hydraulic pressure acting on the lock-up relay valve, which then controls operation of the lock-up clutch.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P2769 Short in Torque Converter Clutch Solenoid Circuit (Shift Solenoid Valve SL) ECM detects a short in the shift solenoid valve SL circuit when the shift solenoid valve SL is operated (1 trip detection logic).
·

Short in shift solenoid valve SL circuit

·

Shift solenoid valve SL

·

ECM


- DTC stored
P2770 Open in Torque Converter Clutch Solenoid Circuit (Shift Solenoid Valve SL) ECM detects an open in the shift solenoid valve SL circuit when the shift solenoid valve SL is not operated (1 trip detection logic).
·

Open in shift solenoid valve SL circuit

·

Shift solenoid valve SL

·

ECM


- DTC stored

Fail-safe function:

If the ECM detects a malfunction, it turns shift solenoid valve SL off.

MONITOR DESCRIPTION

Based on the signals from the throttle position sensor, the air flow meter and the crankshaft position sensor, the ECM sends a signal to shift solenoid valve SL to regulate the hydraulic pressure and provide smoother torque converter engagement. Shift solenoid valve SL responds to commands from the ECM.

The valve controls the lock-up relay valve to perform the torque-converter lock-up function. If the ECM detects an open or short in the shift solenoid valve SL circuit, it will store the DTC.

WIRING DIAGRAM

C311454E16
1.49,1.719 5.01,1.917 3.521,0.198 10 false Shift Solenoid Valve SL 1.521,2.719 2.292,2.958 0.771,0.24 10 false C31 1.521,2.875 5.042,3.073 3.521,0.198 10 false Transmission Wire 5.563,2.927 5.875,3.125 0.313,0.198 10 false C41 5.573,3.094 6.031,3.292 0.458,0.198 10 false ECM 3.333,1.146 3.646,1.344 0.313,0.198 10 false SL 5.156,1.146 5.469,1.344 0.313,0.198 10 false SL 3.604,1.146 3.917,1.344 0.313,0.198 10 false 1 4.927,1.146 5.24,1.344 0.313,0.198 10 false 13 5.771,0.854 6.25,1.073 0.479,0.219 10 false 12 V

CAUTION / NOTICE / HINT

NOTICE:

Perform registration and/or initialization when parts related to the automatic transmission are replaced.

Click hereDrivetrain>AC60E AUTOMATIC TRANSMISSION / TRANSAXLE>AUTOMATIC TRANSMISSION SYSTEM(for 1GD-FTV)>INITIALIZATION


HINT:

After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.



PROCEDURE

1.INSPECT TRANSMISSION WIRE (SHIFT SOLENOID VALVE SL)
a.
C319326C09
2.708,1.771 2.469,1 true 0.156,0.104 0.469,0.302 0.313,0.198 10 false *a 2.688,1.823 3.156,2.083 0.469,0.26 10 false SL
*a Component without harness connected
(Transmission Wire)


Disconnect the transmission wire connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (SL) - Body ground 20°C (68°F) 11 to 15 Ω



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - ECM)

NG

3.INSPECT SHIFT SOLENOID VALVE SL
2.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - ECM)
a.
C318003C05
1.781,0.281 2.135,0.5 0.354,0.219 2.479,2.698 1.865,1.896 true 1.844,0.323 2.156,0.521 0.313,0.198 10 false C41 0.094,0.104 0.406,0.302 0.313,0.198 10 false *a 2.344,2.771 3.01,2.948 0.667,0.177 10 false 13 (SL)
*a Rear view of wire harness connector
(to ECM)


Disconnect the ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C41-13 (SL) - Body ground 20°C (68°F) 11 to 15 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT SHIFT SOLENOID VALVE SL
a.
C320237C01
0.177,0.177 0.49,0.375 0.313,0.198 10 false *1 2.583,1.469 2.896,1.667 0.313,0.198 10 false (+) 3.177,1.458 3.427,1.667 0.25,0.208 10 false (-)
*1 Shift Solenoid Valve SL


Remove shift solenoid valve SL.

Click hereDrivetrain>AC60E AUTOMATIC TRANSMISSION / TRANSAXLE>VALVE BODY ASSEMBLY>DISASSEMBLY


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Shift solenoid valve SL connector terminal - Shift solenoid valve SL body 20°C (68°F) 11 to 15 Ω



c.

Apply 12 V battery voltage to the shift solenoid valve and check that the valve moves and makes an operating noise.

OK:
Measurement Condition Specified Condition
·

Battery positive (+) → Shift solenoid valve SL connector

·

Battery negative (-) → Shift solenoid valve SL body


Valve moves and makes an operating noise



Result:
Proceed to
OK
NG



OK

NG