Home › Drivetrain › AC60E AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSMISSION SYSTEM(for 2GD-FTV) › from 2016.01
RM3270E _52 Drivetrain _048959 AC60E AUTOMATIC TRANSMISSION / TRANSAXLE _0245466 AUTOMATIC TRANSMISSION SYSTEM(for 2GD-FTV) C

AC60E AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM(for 2GD-FTV)  P0720  Output Speed Sensor Circuit  P0722  Output Speed Sensor Circuit No Signal  


DESCRIPTION

This sensor detects the rotation speed of the transmission output shaft and sends signals to the ECM. By comparing the input turbine speed signal (NT) with the output shaft speed sensor signal (SP2), the ECM detects the shift timing of the gears and appropriately controls the engine torque and hydraulic pressure according to various conditions. As a result, the gears shift smoothly.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0720 Output Speed Sensor Circuit When the transmission revolution sensor (SP2) input voltage is either higher than 1.9 V or below 0.1 V for 4.5 seconds or more (2 trip detection logic).
·

Open or short in transmission revolution sensor (SP2) circuit

·

Transmission revolution sensor (SP2)

·

ECM


Comes on DTC stored
P0722 Output Speed Sensor Circuit No Signal All conditions are met for 5 seconds or more (2 trip detection logic):
(a) Park/neutral position switch D input signal is ON.
(b) Either condition is met.
·

Gear position is 1st:

Transmission revolution sensor (NT) value is more than 1240 rpm.

·

Gear position is 2nd, 3rd, 4th, 5th or 6th:

Transmission revolution sensor (NT) value is more than 720 rpm.


(c) The vehicle speed is 9 km/h (5.6 mph) or more.
(d) No signal from transmission revolution sensor (SP2) is input to the ECM.
·

Open or short in transmission revolution sensor (SP2) circuit

·

Transmission revolution sensor (SP2)

·

ECM


Comes on DTC stored

MONITOR DESCRIPTION

The transmission revolution sensor (SP2) detects the transmission output shaft speed. The ECM calculates gear shifts comparing the transmission revolution sensor (NT) with the transmission revolution sensor (SP2).

If the ECM detects no signal from the transmission revolution sensor (SP2) even while the vehicle is moving, it will conclude that there is a malfunction in the transmission revolution sensor (SP2). The ECM will illuminate the MIL and store the DTC.

WIRING DIAGRAM

C311983E18
0.521,3.146 3.021,3.375 2.5,0.229 10 false Transmission Revolution Sensor (SP2) 5.427,3.354 5.885,3.552 0.458,0.198 10 false ECM 2.656,1.167 3.271,1.365 0.615,0.198 10 false SP2B 2.635,2.292 3.25,2.49 0.615,0.198 10 false SP2O 0.552,2.958 1.01,3.156 0.458,0.198 10 false C2 5.427,3.208 5.885,3.406 0.458,0.198 10 false C40 4.875,2.292 5.188,2.49 0.313,0.198 10 false 11 4.875,1.167 5.188,1.365 0.313,0.198 10 false 10 3.125,2.302 3.438,2.5 0.313,0.198 10 false 1 3.115,1.167 3.427,1.365 0.313,0.198 10 false 2 5.75,0.99 6.219,1.188 0.469,0.198 10 false 12 V 5.115,1.177 5.729,1.375 0.615,0.198 10 false SP2B 5.125,2.292 5.74,2.49 0.615,0.198 10 false SP2O

CAUTION / NOTICE / HINT

HINT:

After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.

2.

Turn the ignition switch off.

3.

Perform step (*1) again.



DATA LIST


HINT:

Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed.

Reading the Data List information early in troubleshooting is one way to save diagnostic time.


NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


a.

Warm up the engine.


b.

Turn the ignition switch off.


c.

Connect the GTS to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the GTS on.


f.

Enter the following menus: Powertrain / Engine and ECT / Data List.


g.

According to the display on the GTS, read the Data List.

Powertrain > Engine > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
SPD (SP2) Output shaft speed Min.: 0 km/h (0 mph)
Max.: 255 km/h (158 mph)
0 km/h (0 mph): Vehicle stopped (equal to vehicle speed) -
Powertrain > Engine > Data List
Tester Display
SPD (SP2)
50003 234 404
HINT:
·

SPD (SP2) is always 0 while driving: Open or short in the sensor or circuit.

·

SPD (SP2) value displayed on the GTS is much lower than the actual vehicle speed: Sensor trouble, improper installation, or intermittent connection trouble of the circuit.





PROCEDURE

1.READ VALUE USING GTS (SPD (SP2) AND SP2 SENSOR VOLTAGE)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List.


e.

In accordance with the display on the GTS, read the Data List.

Powertrain > Engine > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
SPD (SP2) Output shaft speed Min.: 0 km/h (0 mph)
Max.: 255 km/h (158 mph)
0 km/h (0 mph): Vehicle stopped (equal to vehicle speed) -
SP2 Sensor Voltage Transmission revolution sensor (SP2) output voltage Min.: 0.000 V
Max.: 4.999 V
0.1 to 1.9 V: Engine idling -
Powertrain > Engine > Data List
Tester Display
SPD (SP2)
SP2 Sensor Voltage
50003 234 404,405

Result:
Result Proceed to
Data display is not within Normal Condition range A
Data display is within Normal Condition range B



A

2.INSPECT TRANSMISSION REVOLUTION SENSOR (SP2)

B

2.INSPECT TRANSMISSION REVOLUTION SENSOR (SP2)
a.

Remove the transmission revolution sensor (SP2).

Click hereDrivetrain>AC60E AUTOMATIC TRANSMISSION / TRANSAXLE>SPEED SENSOR>REMOVAL


b.

Connect the battery to the sensor as shown in the illustration.

C297974C11
3.688,0.646 3.917,0.646 true 4.854,0.385 4.99,0.5 true 5.74,0.823 6.031,0.823 true 5.333,2.25 5.625,1.844 true 4.51,2.573 4.823,2.385 true 4.271,0.792 4.5,0.792 true 1.26,1.844 1.542,1.448 true 2.115,1.896 1.833,1.448 true 0.833,0.885 1.146,1.042 0.313,0.156 10 false *1 5.021,0.5 5.333,0.656 0.313,0.156 10 false *2 6.073,0.76 6.385,0.917 0.313,0.156 10 false *3 5.635,1.708 5.948,1.865 0.313,0.156 10 false *4 4.354,2.552 4.667,2.708 0.313,0.156 10 false *a 3.031,0.563 3.74,0.781 0.708,0.219 10 false 2 (SP2B) 4.542,0.708 5.25,0.927 0.708,0.219 10 false 1 (SP2O) 1.979,1.938 2.688,2.156 0.708,0.219 10 false SP2O 1.094,1.927 1.802,2.146 0.708,0.219 10 false SP2B
*1 Transmission Revolution Sensor (SP2) *2 Ammeter
*3 Battery *4 Magnet
*a 5 mm (0.197 in.) or less - -



c.

Wave a magnetic object left and right in front of the transmission revolution sensor (SP2) tip (5 mm (0.197 in.) or less) to change the high/low signals while measuring the current.

NOTICE:

Make sure to wave the magnetic object during the inspection. The current will not change without waving the magnetic object as indicated by the arrow in the illustration.



d.

Measure the current according to the value(s) in the table below.

Standard Current:
Tester Connection Condition Specified Condition
1 (SP2O) - 2 (SP2B) Low signal 4 to 8 mA
1 (SP2O) - 2 (SP2B) High signal 12 to 16 mA



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (TRANSMISSION REVOLUTION SENSOR (SP2) - ECM)

NG

REPLACE TRANSMISSION REVOLUTION SENSOR (SP2)

3.CHECK HARNESS AND CONNECTOR (TRANSMISSION REVOLUTION SENSOR (SP2) - ECM)
a.

Disconnect the C2 transmission revolution sensor (SP2) connector.


b.

Disconnect the C40 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C2-2 (SP2B) - C40-10 (SP2B) Always Below 1 Ω
C2-1 (SP2O) - C40-11 (SP2O) Always Below 1 Ω
C2-2 (SP2B) - Body ground Always 10 kΩ or higher
C2-1 (SP2O) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR