51441
1.REMOVE NO. 1 ENGINE UNDER COVER
51442
2.REMOVE NO. 2 ENGINE UNDER COVER
3.DRAIN DIFFERENTIAL OIL
37140
4.REMOVE FRONT PROPELLER SHAFT ASSEMBLY
for TSAM Made:
Click hereDrivetrain>DRIVE SHAFT / PROPELLER SHAFT>FRONT PROPELLER SHAFT ASSEMBLY(for TSAM Made)>REMOVAL
except TSAM Made:
Click hereDrivetrain>DRIVE SHAFT / PROPELLER SHAFT>FRONT PROPELLER SHAFT ASSEMBLY(except TSAM Made)>REMOVAL
41204D
5.REMOVE FRONT DRIVE PINION COMPANION FLANGE NUT
Using SST and a hammer, loosen the staked part of the front drive pinion companion flange nut.
| *a | Turn |
| *b | Hold |
Using SST to hold the companion flange, remove the front drive pinion companion flange nut.
41204D
6.REMOVE FRONT DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY WITH DUST DEFLECTOR
Using SST, remove the front drive pinion companion flange sub-assembly with dust deflector.
Before using SST (center bolt), apply hypoid gear oil to its threads and tip.
7.REMOVE FRONT DIFFERENTIAL CARRIER OIL SEAL
| *1 | Front Differential Carrier Oil Seal |
| *2 | Front Differential Drive Pinion Oil Slinger |
Using SST, remove the front differential carrier oil seal.
41214C
8.REMOVE FRONT DIFFERENTIAL DRIVE PINION OIL SLINGER
Remove the front differential drive pinion oil slinger from the differential drive pinion.
41211B
9.REMOVE FRONT DRIVE PINION REAR TAPERED ROLLER BEARING
Using SST, remove the front drive pinion rear tapered roller bearing (inner).
Using SST, tap out the front drive pinion rear tapered roller bearing (outer).
41115F
10.REMOVE FRONT DIFFERENTIAL OIL STORAGE RING
Using a screwdriver and hammer, tap out the front differential oil storage ring.
41231F
11.REMOVE FRONT DIFFERENTIAL DRIVE PINION BEARING SPACER
Remove the front differential drive pinion bearing spacer from the differential drive pinion.
41231F
12.INSTALL FRONT DIFFERENTIAL DRIVE PINION BEARING SPACER
Install a new front differential drive pinion bearing spacer.
Make sure the front differential drive pinion bearing spacer is installed correctly.
41115F
13.INSTALL FRONT DIFFERENTIAL OIL STORAGE RING
Using a brass bar and hammer, tap in a new front differential oil storage ring.
Be careful not to damage the front differential oil storage ring.
41211B
14.INSTALL FRONT DRIVE PINION REAR TAPERED ROLLER BEARING
Using SST and a hammer, install the front drive pinion rear tapered roller bearing (outer).
Install the front drive pinion rear tapered roller bearing (inner).
41214C
15.INSTALL FRONT DIFFERENTIAL DRIVE PINION OIL SLINGER
Install the front differential drive pinion oil slinger to the differential drive pinion.
16.INSTALL FRONT DIFFERENTIAL CARRIER OIL SEAL
Apply MP grease to the lip of a new front differential carrier oil seal.
| *a | Front Differential Carrier Oil Seal Depth |
Using SST and a hammer, tap in the front differential carrier oil seal.
2.7 to 3.3 mm (0.107 to 0.129 in.)
41204D
17.INSTALL FRONT DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY WITH DUST DEFLECTOR
Using SST, install the front drive pinion companion flange sub-assembly with dust deflector.
Before using SST (center bolt), apply hypoid gear oil to its threads and tip.
Apply hypoid gear oil LSD to the drive pinion thread and nut seat face.
| *a | Turn |
| *b | Hold |
Using SST to hold the companion flange, install a new front drive pinion companion flange nut.
370 N*m (3773 kgf*cm, 273 ft.*lbf) or less
18.INSPECT TOTAL PRELOAD
Using a torque wrench, measure the preload with the teeth of the drive pinion and ring gear in contact.
| Item | Specified Condition |
|---|---|
| New bearing | 1.3 to 2.9 N*m (14 to 29 kgf*cm, 12 to 25 in.*lbf) |
| Reused bearing | 1.29 to 2.79 N*m (14 to 28 kgf*cm, 12 to 24 in.*lbf) |
If necessary, disassemble and inspect the differential.
41204D
19.STAKE FRONT DRIVE PINION COMPANION FLANGE NUT
Using a chisel and hammer, stake the front drive pinion companion flange nut.
37140
20.INSTALL FRONT PROPELLER SHAFT ASSEMBLY
for TSAM Made:
Click hereDrivetrain>DRIVE SHAFT / PROPELLER SHAFT>FRONT PROPELLER SHAFT ASSEMBLY(for TSAM Made)>INSTALLATION
except TSAM Made:
21.ADD DIFFERENTIAL OIL
51442
22.INSTALL NO. 2 ENGINE UNDER COVER
51441
23.INSTALL NO. 1 ENGINE UNDER COVER