Home › Vehicle Interior › DOOR LOCK › FRONT DOOR LOCK › from 2016.01
RM3270E _58 Vehicle Interior _041705 DOOR LOCK _0205680 FRONT DOOR LOCK G

DOOR LOCK  FRONT DOOR LOCK  INSPECTION  


PROCEDURE

Hide 69310 1.INSPECT FRONT DOOR LOCK ASSEMBLY RH (w/o Double Locking System)

a.
B340409C06
1.24,3.521 0.792,3.521 true 2.167,3.521 2.563,3.521 true 1.938,4.177 1.75,3.823 true 1.594,3.813 1.375,4.167 true 1.115,2.052 1.427,2.25 0.313,0.198 10 false *a 1.698,2.469 2.01,2.667 0.313,0.198 10 false *b 0.844,2.854 1.156,3.052 0.313,0.198 10 false *c 0.688,3.448 0.844,3.646 0.156,0.198 10 false L 2.646,3.448 2.958,3.646 0.313,0.198 10 false UL 1.844,4.229 2.458,4.427 0.615,0.198 10 false LSSR 1.292,4.208 1.448,4.406 0.156,0.198 10 false E
*a Unlock
*b Lock
*c Component without harness connected
(Front Door Lock Assembly RH)


Check the door lock motor operation.

i.

Apply battery voltage to the motor connector and check the operation of the door lock motor.

OK:
Measurement Condition Specified Condition
Battery positive (+) → 4 (L)
Battery negative (-) → 1 (UL)
Lock
Battery positive (+) → 1 (UL)
Battery negative (-) → 4 (L)
Unlock


If the result is not as specified, replace the front door lock assembly RH.



b.

Check the resistance of the door unlock detection switch.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
7 (LSSR) - 8 (E) Lock 10 kΩ or higher
7 (LSSR) - 8 (E) Unlock Below 1 Ω


If the result is not as specified, replace the front door lock assembly RH.



c.
B340408C12
1.969,3.813 2.156,4.219 true 1.604,3.792 1.49,4.198 true 2.177,3.76 2.552,3.76 true 0.604,0.531 0.917,0.729 0.313,0.198 10 false *a 0.406,0.958 0.719,1.156 0.313,0.198 10 false *b 0.635,1.406 0.948,1.604 0.313,0.198 10 false *c 0.792,2.865 1.104,3.063 0.313,0.198 10 false *d 2.604,3.646 2.917,3.844 0.313,0.198 10 false UL 2.146,4.26 2.302,4.458 0.156,0.198 10 false L 1.417,4.25 1.573,4.448 0.156,0.198 10 false E
*a Unlock
*b Neutral
*c Lock
*d Component without harness connected
(Front Door Lock Assembly RH)


Check the resistance of the lock and unlock switch (for RHD).

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
6 (L) - 8 (E) Lock Below 1 Ω
6 (L) - 8 (E)
5 (UL) - 8 (E)
Neutral 10 kΩ or higher
5 (UL) - 8 (E) Unlock Below 1 Ω


If the result is not as specified, replace the front door lock assembly RH.



Hide 69310 2.INSPECT FRONT DOOR LOCK ASSEMBLY RH (w/ Double Locking System)

a.
B438947C01
2.021,3.823 2.271,3.823 true 1.719,3.74 1.719,3.146 1.719,3.146 1.99,3.146 true 1.49,3.74 1.49,3.146 1.49,3.146 1.271,3.146 true 0.938,3.813 1.188,3.813 true 0.635,2.885 0.948,3.083 0.313,0.198 10 false *c 0.75,2.396 1.063,2.594 0.313,0.198 10 false *a 1.115,2.76 1.427,2.958 0.313,0.198 10 false *b 2.052,3.083 2.208,3.281 0.156,0.198 10 false L 2.313,3.75 2.594,3.938 0.281,0.188 10 false UL 0.729,3.698 1.01,3.906 0.281,0.208 10 false DL 0.906,3.073 1.302,3.281 0.396,0.208 10 false UNDL
*a Unlock
*b Lock
*c Component without harness connected
(Front Door Lock Assembly RH)


Check the door lock motor operation.

i.

Apply battery voltage and check the operation of the front door lock motor and double lock motor.

OK:
Measurement Condition Specified Condition
Battery positive (+) → 2 (L)
Battery negative (-) → 1 (UL)
Lock
Battery positive (+) → 1 (UL)
Battery negative (-) → 2 (L)
Unlock
Battery positive (+) → 4 (DL)
Battery negative (-) → 3 (UNDL)
Set
Battery positive (+) → 3 (UNDL)
Battery negative (-) → 4 (DL)
Unset


HINT:
·

Move the door lock motor to the lock position and set the double locking system. Check that the doors cannot be unlocked by operating the control cable.

·

Move the door lock motor to the lock position and unset the double locking system. Check that the doors can be unlocked by operating the control cable.



If the result is not as specified, replace the front door lock assembly RH.



b.
B438947C05
1.656,4.458 1.531,4.458 1.531,4.458 1.531,4.031 true 1.99,4.333 1.688,4.333 1.688,4.333 1.688,4.031 true 1.208,4.469 1.385,4.469 1.385,4.469 1.385,4.042 true 0.885,3.99 1.177,3.99 true 0.635,2.885 0.948,3.083 0.313,0.198 10 false *c 0.75,2.396 1.063,2.594 0.313,0.198 10 false *a 1.115,2.76 1.427,2.958 0.313,0.198 10 false *b 2.042,4.271 2.656,4.469 0.615,0.198 10 false LSSR 1.719,4.406 1.885,4.604 0.167,0.198 10 false E 0.76,3.927 0.917,4.125 0.156,0.198 10 false E 0.813,4.396 1.427,4.594 0.615,0.198 10 false DLSR
*a Unlock
*b Lock
*c Component without harness connected
(Front Door Lock Assembly RH)


Check the operation of the door unlock detection switch and double lock position switch.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
7 (LSSR) - 8 (E) Lock 10 kΩ or higher
7 (LSSR) - 8 (E) Unlock Below 1 Ω
9 (DLSR) - 10 (E) Unset 10 kΩ or higher
9 (DLSR) - 10 (E) Set Below 1 Ω


If the result is not as specified, replace the front door lock assembly RH.



c.
B438948C01
2.031,3.99 2.396,3.99 true 1.844,4.052 1.844,4.438 1.844,4.438 2.125,4.438 true 1.531,4.042 1.531,4.427 1.531,4.427 1.323,4.427 true 1.135,0.427 1.448,0.625 0.313,0.198 10 false *a 1.313,1.24 1.625,1.438 0.313,0.198 10 false *b 0.854,1.688 1.167,1.885 0.313,0.198 10 false *c 1.167,4.344 1.323,4.542 0.156,0.198 10 false E 2.438,3.917 2.688,4.167 0.25,0.25 10 false UL 0.719,3.115 1.031,3.313 0.313,0.198 10 false *d 2.167,4.354 2.417,4.604 0.25,0.25 10 false L
*a Unlock
*b Neutral
*c Lock
*d Component without harness connected
(Front Door Lock Assembly RH)


Check the resistance of the door key lock and unlock switch.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
6 (L) - 8 (E) Lock Below 1 Ω
6 (L) - 8 (E)
5 (UL) - 8 (E)
Neutral 10 kΩ or higher
5 (UL) - 8 (E) Unlock Below 1 Ω


If the result is not as specified, replace the front door lock assembly RH.



Hide 69320 3.INSPECT FRONT DOOR LOCK ASSEMBLY LH (w/o Double Locking System)

a.
B380493C01
1.24,3.521 0.823,3.521 true 2.156,3.521 2.604,3.521 true 1.802,3.823 1.927,4.125 true 1.615,3.813 1.427,4.156 true 2.208,2.083 2.521,2.24 0.313,0.156 10 false *a 1.635,2.49 1.948,2.646 0.313,0.156 10 false *b 0.813,2.813 1.125,2.969 0.313,0.156 10 false *c 0.698,3.438 0.854,3.635 0.156,0.198 10 false L 2.677,3.448 2.99,3.646 0.313,0.198 10 false UL 1.927,4.177 2.083,4.375 0.156,0.198 10 false E 1.25,4.198 1.865,4.396 0.615,0.198 10 false LSSR
*a Unlock
*b Lock
*c Component without harness connected
(Front Door Lock Assembly LH)


Check the door lock motor operation.

i.

Apply battery voltage to the motor connector and check the operation of the door lock motor.

OK:
Measurement Condition Specified Condition
Battery positive (+) → Terminal 4 (L)
Battery negative (-) → Terminal 1 (UL)
Lock
Battery positive (+) → Terminal 1 (UL)
Battery negative (-) → Terminal 4 (L)
Unlock


If the result is not as specified, replace the front door lock assembly LH.



b.

Check the resistance of the door unlock detection switch.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
7 (E) - 8 (LSSR) Lock 10 kΩ or higher
Unlock Below 1 Ω


If the result is not as specified, replace the front door lock assembly LH.



c.
B380175C02
1.302,4.25 1.417,3.896 true 1.823,3.885 1.938,4.229 true 1.26,3.885 0.906,4.073 true 2.656,0.49 2.969,0.688 0.313,0.198 10 false *a 2.896,0.938 3.208,1.135 0.313,0.198 10 false *b 2.708,1.417 3.021,1.615 0.313,0.198 10 false *c 0.719,2.927 1.031,3.125 0.313,0.198 10 false *d 1.25,4.292 1.406,4.49 0.156,0.198 10 false L 1.906,4.302 2.063,4.5 0.156,0.198 10 false E 0.698,4.031 1.01,4.229 0.313,0.198 10 false UL
*a Unlock
*b Neutral
*c Lock
*d Component without harness connected
(Front Door Lock Assembly LH)


Check the resistance of the lock and unlock switch (for LHD).

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
9 (L) - 7 (E) Lock Below 1 Ω
9 (L) - 7 (E)
10 (UL) - 7 (E)
Neutral 10 kΩ or higher
10 (UL) - 7 (E) Unlock Below 1 Ω


If the result is not as specified, replace the front door lock assembly LH.



Hide 69320 4.INSPECT FRONT DOOR LOCK ASSEMBLY LH (w/ Double Locking System)

a.
B438946C01
2.01,3.813 2.375,3.813 true 1.719,3.75 1.719,3.094 1.719,3.094 1.917,3.094 true 1.49,3.75 1.49,3.094 1.49,3.094 1.313,3.094 true 0.833,3.823 1.198,3.823 true 0.771,2.833 1.083,3.031 0.313,0.198 10 false *c 2.531,2.448 2.844,2.646 0.313,0.198 10 false *a 2.167,2.771 2.479,2.969 0.313,0.198 10 false *b 2.438,3.729 3.052,3.927 0.615,0.198 10 false UNDL 1.969,3.021 2.583,3.219 0.615,0.198 10 false DL 1.104,3 1.417,3.198 0.313,0.198 10 false UL 0.719,3.74 1.031,3.938 0.313,0.198 10 false L
*a Unlock
*b Lock
*c Component without harness connected
(Front Door Lock Assembly LH)


Check the door lock motor operation.

i.

Apply battery voltage and check the operation of the front door lock motor and double lock motor.

OK:
Measurement Condition Specified Condition
Battery positive (+) → 4 (L)
Battery negative (-) → 3 (UL)
Lock
Battery positive (+) → 3 (UL)
Battery negative (-) → 4 (L)
Unlock
Battery positive (+) → 2 (DL)
Battery negative (-) → 1 (UNDL)
Set
Battery positive (+) → 1 (UNDL)
Battery negative (-) → 2 (DL)
Unset


HINT:
·

Move the door lock motor to the lock position and set the double locking system. Check that the doors cannot be unlocked by operating the control cable.

·

Move the door lock motor to the lock position and unset the double locking system. Check that the doors can be unlocked by operating the control cable.



If the result is not as specified, replace the front door lock assembly LH.



b.
B438946C02
1.833,4.042 1.833,4.313 1.833,4.313 2.302,4.313 true 1.688,4.052 1.688,4.469 1.688,4.469 1.844,4.469 true 2.021,4 2.365,4 true 1.531,4.021 1.531,4.438 1.531,4.438 1.344,4.438 true 0.563,3.042 0.875,3.24 0.313,0.198 10 false *c 2.469,2.448 2.781,2.646 0.313,0.198 10 false *a 2.146,2.75 2.458,2.948 0.313,0.198 10 false *b 2.417,3.938 2.573,4.135 0.156,0.198 10 false E 2.375,4.25 2.844,4.438 0.469,0.188 10 false DLSR 0.938,4.365 1.406,4.552 0.469,0.188 10 false LSSR 1.885,4.396 2.042,4.594 0.156,0.198 10 false E
*a Unlock
*b Lock
*c Component without harness connected
(Front Door Lock Assembly LH)


Check the operation of the door unlock detection switch and double lock position switch.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
8 (LSSR) - 7 (E) Lock 10 kΩ or higher
8 (LSSR) - 7 (E) Unlock Below 1 Ω
6 (DLSR) - 5 (E) Unset 10 kΩ or higher
6 (DLSR) - 5 (E) Set Below 1 Ω


If the result is not as specified, replace the front door lock assembly LH.