Home › Vehicle Interior › DOOR LOCK › REAR DOOR LOCK › from 2016.01
RM3270E _58 Vehicle Interior _041705 DOOR LOCK _0205681 REAR DOOR LOCK G

DOOR LOCK  REAR DOOR LOCK  INSPECTION  


PROCEDURE

Hide 69330 1.INSPECT REAR DOOR LOCK ASSEMBLY RH (w/o Double Locking System)

a.
B340416C06
1.271,3.594 0.917,3.594 true 2.177,3.594 2.5,3.594 true 2.021,3.885 2.104,4.198 true 1.438,3.875 1.323,4.208 true 1.063,2.104 1.375,2.302 0.313,0.198 10 false *a 1.615,2.323 1.927,2.521 0.313,0.198 10 false *b 0.75,2.865 1.063,3.063 0.313,0.198 10 false *c 0.802,3.531 0.958,3.729 0.156,0.198 10 false L 2.563,3.521 2.875,3.719 0.313,0.198 10 false UL 1.979,4.24 2.594,4.438 0.615,0.198 10 false LSSR 1.281,4.24 1.438,4.438 0.156,0.198 10 false E
*a Unlock
*b Lock
*c Component without harness connected
(Rear Door Lock Assembly RH)


Check the door lock motor operation.

i.

Apply battery voltage to the motor connector and check the operation of the door lock motor.

OK:
Measurement Condition Specified Condition
Battery positive (+) → Terminal 4 (L)
Battery negative (-) → Terminal 1 (UL)
Lock
Battery positive (+) → Terminal 1 (UL)
Battery negative (-) → Terminal 4 (L)
Unlock


If the result is not as specified, replace the rear door lock assembly RH.



b.

Check the resistance of the unlock detection switch.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
6 (LSSR) - 9 (E) Lock 10 kΩ or higher
6 (LSSR) - 9 (E) Unlock Below 1 Ω


If the result is not as specified, replace the rear door lock assembly RH.



Hide 69330 2.INSPECT REAR DOOR LOCK ASSEMBLY RH (w/ Double Locking System)

a.
B438950C01
2.021,3.813 2.354,3.813 true 1.729,3.75 1.729,3.208 1.729,3.208 2.135,3.208 true 1.5,3.75 1.5,3.208 1.5,3.208 1.01,3.208 true 0.865,3.813 1.198,3.813 true 1.323,2.927 1.635,3.125 0.313,0.198 10 false *a 1.979,2.906 2.292,3.104 0.313,0.198 10 false *b 0.208,3.271 0.521,3.469 0.313,0.198 10 false *c 0.802,3.146 1.115,3.344 0.313,0.198 10 false UL 0.76,3.75 1.073,3.948 0.313,0.198 10 false L 2.198,3.146 2.51,3.344 0.313,0.198 10 false DL 2.396,3.75 2.854,3.948 0.458,0.198 10 false UNDL
*a Unlock
*b Lock
*c Component without harness connected
(Rear Door Lock Assembly RH)


Check the operation of the door lock motor and double lock motor.

i.

Apply battery voltage and check the operation of the rear door lock motor and double lock motor.

OK:
Measurement Condition Specified Condition
Battery positive (+) → 4 (L)
Battery negative (-) → 3 (UL)
Lock
Battery positive (+) → 3 (UL)
Battery negative (-) → 4 (L)
Unlock
Battery positive (+) → 2 (DL)
Battery negative (-) → 1 (UNDL)
Set
Battery positive (+) → 1 (UNDL)
Battery negative (-) → 2 (DL)
Unset


HINT:
·

Move the door lock motor to the lock position and set the double locking system. Check that the doors cannot be unlocked by operating the control cable.

·

Move the door lock motor to the lock position and unset the double locking system. Check that the doors can be unlocked by operating the control cable.



If the result is not as specified, replace the rear door lock assembly RH.



b.
B438950C02
2.021,3.99 2.354,3.99 true 1.833,4.031 1.833,4.396 1.833,4.396 2.219,4.396 true 1.385,4.031 1.385,4.417 1.385,4.417 1.052,4.417 true 0.865,3.99 1.198,3.99 true 1.323,2.927 1.635,3.125 0.313,0.198 10 false *a 1.979,2.906 2.292,3.104 0.313,0.198 10 false *b 0.208,3.271 0.521,3.469 0.313,0.198 10 false *c 0.667,4.333 1.125,4.49 0.458,0.156 10 false LSSR 0.74,3.906 1.052,4.104 0.313,0.198 10 false E 2.396,3.917 2.854,4.115 0.458,0.198 10 false DLSR 2.271,4.333 2.427,4.531 0.156,0.198 10 false E
*a Unlock
*b Lock
*c Component without harness connected
(Rear Door Lock Assembly RH)


Check the operation of the unlock detection switch and double lock position switch.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
9 (LSSR) - 10 (E) Lock 10 kΩ or higher
9 (LSSR) - 10 (E) Unlock Below 1 Ω
5 (DLSR) - 6 (E) Unset 10 kΩ or higher
5 (DLSR) - 6 (E) Set Below 1 Ω


If the result is not as specified, replace the rear door lock assembly RH.



Hide 69340 3.INSPECT REAR DOOR LOCK ASSEMBLY LH (w/o Double Locking System)

a.
B340417C06
1.292,3.594 0.917,3.594 true 2.156,3.615 2.521,3.615 true 1.479,3.865 1.479,4.177 true 1.979,3.875 1.979,4.198 true 2.083,2.094 2.396,2.292 0.313,0.198 10 false *a 1.615,2.292 2,2.49 0.385,0.198 10 false *b 0.833,2.917 1.146,3.115 0.313,0.198 10 false *c 0.802,3.51 0.958,3.708 0.156,0.198 10 false L 2.583,3.531 2.896,3.729 0.313,0.198 10 false UL 1.438,4.229 1.594,4.427 0.156,0.198 10 false E 1.823,4.219 2.438,4.417 0.615,0.198 10 false LSSR
*a Unlock
*b Lock
*c Component without harness connected
(Rear Door Lock Assembly LH)


Check the door lock motor operation.

i.

Apply battery voltage to the motor connector and check the operation of the door lock motor.

OK:
Measurement Condition Specified Condition
Battery positive (+) → Terminal 4 (L)
Battery negative (-) → Terminal 1 (UL)
Lock
Battery positive (+) → Terminal 1 (UL)
Battery negative (-) → Terminal 4 (L)
Unlock


If the result is not as specified, replace the rear door lock assembly LH.



b.

Check the resistance of the door unlock detection switch.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
6 (LSSR) - 9 (E) Lock 10 kΩ or higher
6 (LSSR) - 9 (E) Unlock Below 1 Ω


If the result is not as specified, replace the rear door lock assembly LH.



Hide 69340 4.INSPECT REAR DOOR LOCK ASSEMBLY LH (w/ Double Locking System)

a.
B438949C03
0.917,3.823 1.208,3.823 true 2.021,3.823 2.313,3.823 true 1.729,3.75 1.729,3.208 1.729,3.208 2.25,3.208 true 1.5,3.75 1.5,3.208 1.5,3.208 0.958,3.208 true 1.875,2.896 2.188,3.094 0.313,0.198 10 false *a 1.219,2.875 1.531,3.073 0.313,0.198 10 false *b 0.323,3.042 0.635,3.24 0.313,0.198 10 false *c 0.563,3.146 1.021,3.354 0.458,0.208 10 false UNDL 2.375,3.75 2.802,3.948 0.427,0.198 10 false UL 0.698,3.75 1.01,3.948 0.313,0.198 10 false DL 2.302,3.146 2.531,3.323 0.229,0.177 10 false L
*a Unlock
*b Lock
*c Component without harness connected
(Rear Door Lock Assembly LH)


Check the operation of the door lock motor and double lock motor.

i.

Apply battery voltage and check the operation of the rear door lock motor and double lock motor.

OK:
Measurement Condition Specified Condition
Battery positive (+) → 2 (L)
Battery negative (-) → 1 (UL)
Lock
Battery positive (+) → 1 (UL)
Battery negative (-) → 2 (L)
Unlock
Battery positive (+) → 4 (DL)
Battery negative (-) → 3 (UNDL)
Set
Battery positive (+) → 3 (UNDL)
Battery negative (-) → 4 (DL)
Unset


HINT:
·

Move the door lock motor to the lock position and set the double locking system. Check that the doors cannot be unlocked by operating the control cable.

·

Move the door lock motor to the lock position and unset the double locking system. Check that the doors can be unlocked by operating the control cable.



If the result is not as specified, replace the rear door lock assembly LH.



b.
B438949C04
0.896,4 1.188,4 true 2.021,4 2.313,4 true 1.844,4.021 1.844,4.365 1.844,4.365 2.219,4.365 true 1.385,4.021 1.385,4.365 1.385,4.365 1.042,4.365 true 1.875,2.896 2.188,3.094 0.313,0.198 10 false *a 1.219,2.875 1.531,3.073 0.313,0.198 10 false *b 0.323,3.042 0.635,3.24 0.313,0.198 10 false *c 0.646,4.292 1.063,4.563 0.417,0.271 10 false DLSR 2.365,3.917 2.792,4.115 0.427,0.198 10 false LSSR 0.792,3.917 1.104,4.115 0.313,0.198 10 false E 2.25,4.281 2.677,4.479 0.427,0.198 10 false E
*a Unlock
*b Lock
*c Component without harness connected
(Rear Door Lock Assembly LH)


Check the operation of the unlock detection switch and double lock position switch.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
5 (LSSR) - 6 (E) Lock 10 kΩ or higher
5 (LSSR) - 6 (E) Unlock Below 1 Ω
9 (DLSR) - 10 (E) Unset 10 kΩ or higher
9 (DLSR) - 10 (E) Set Below 1 Ω


If the result is not as specified, replace the rear door lock assembly LH.