Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM(for Radio Receiver Type) › from 2016.01
RM3270E _56 Audio / Visual / Telematics _041699 AUDIO / VIDEO _0249874 AUDIO AND VISUAL SYSTEM(for Radio Receiver Type) J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(for Radio Receiver Type)  Vehicle Speed Signal Circuit between Radio Receiver and Combination Meter  


DESCRIPTION

The radio receiver assembly receives a vehicle speed signal from the combination meter assembly to control the ASL function.

HINT:
·

A voltage of 12 V or 5 V is output from each ECU and then input to the combination meter assembly. The signal is changed to a pulse signal at the transistor in the combination meter assembly. Each ECU controls its respective system based on this pulse signal.

·

If a short occurs in any of the ECUs or in the wire harness connected to an ECU, all systems in the diagram below will not operate normally.



WIRING DIAGRAM

E345564E01
0.99,1.5 1.448,1.698 0.458,0.198 10 false ECM 1.865,1.031 2.479,1.229 0.615,0.198 10 false G142 1.938,0.813 2.25,1.01 0.313,0.198 10 false 23 1.917,1.26 2.229,1.458 0.313,0.198 10 false *1 2.313,1.031 2.927,1.229 0.615,0.198 10 false G49 2.365,0.813 2.677,1.01 0.313,0.198 10 false 10 2.354,1.271 2.667,1.469 0.313,0.198 10 false *2 2.688,1.031 3.302,1.229 0.615,0.198 10 false G140 2.76,0.823 3.073,1.021 0.313,0.198 10 false 17 2.76,1.26 3.073,1.458 0.313,0.198 10 false *3 4.948,1.521 6.833,1.74 1.885,0.219 10 false Combination Meter Assembly 4.958,1.323 5.271,1.521 0.313,0.198 10 false G8 5.125,0.906 5.438,1.104 0.313,0.198 10 false 19 5.406,0.917 5.719,1.115 0.313,0.198 10 false +S 5.531,3.25 6.302,3.458 0.771,0.208 10 false Body ECU 5.521,3.042 5.979,3.24 0.458,0.198 10 false G33 5.021,4.906 5.635,5.104 0.615,0.198 10 false G171 5.083,4.198 5.396,4.396 0.313,0.198 10 false 17 5.385,4.188 5.844,4.385 0.458,0.198 10 false SPD 5.396,2.479 5.854,2.677 0.458,0.198 10 false SPD 5.156,2.49 5.313,2.688 0.156,0.198 10 false 5 0.5,3.031 0.958,3.229 0.458,0.198 10 false G16 0.5,3.208 3.594,3.438 3.094,0.229 10 false Certification ECU (Smart Key ECU Assembly)*4 1.479,2.469 1.938,2.667 0.458,0.198 10 false SPD 1.885,2.479 2.042,2.677 0.156,0.198 10 false 7 2.74,2.719 3.104,2.917 0.365,0.198 10 false *4 0.219,5.198 2.75,5.49 2.531,0.292 10 false *4: w/ Smart Entry and Start System 1.49,0.896 1.948,1.094 0.458,0.198 10 false SPD 5.031,5.135 6.719,5.354 1.688,0.219 10 false Radio Receiver Assembly 0.25,3.906 2.396,4.104 2.146,0.198 10 false *1: for 2TR-FE 0.25,4.313 2.396,4.51 2.146,0.198 10 false *2: for 2GD-FTV 0.24,4.771 2.385,4.969 2.146,0.198 10 false *3: for 2KD-FTV

CAUTION / NOTICE / HINT

NOTICE:

Check that the wire harness is properly installed and does not have any sharp bends, pinching or loose connections.


PROCEDURE

1.CHECK COMBINATION METER ASSEMBLY (OUTPUT WAVEFORM)
a.
E256135C28
1.479,0.438 1.896,0.656 0.417,0.219 0.656,1.802 0.865,1.333 true 0.167,0.198 0.479,0.396 0.313,0.198 10 false *a 1.594,0.458 1.906,0.656 0.313,0.198 10 false G8 0.469,1.833 0.781,2.031 0.313,0.198 10 false +S 2.792,3.583 3.188,3.854 0.396,0.271 10 false GND 1.083,3.896 1.479,4.167 0.396,0.271 10 false (A)
*a Component with harness connected
(Combination Meter Assembly)


Check the output waveform.

i.

Remove the combination meter assembly with the connector still connected.


ii.

Connect an oscilloscope to terminal G8-19 (+S) and body ground.


iii.

Turn the ignition switch to ON.


iv.

Turn a wheel slowly.


v.

Check the signal waveform according to the condition(s) in the table below.

Item Condition
Measurement terminal G8-19 (+S) - Body ground
Tool setting 5 V/DIV, 20 ms./DIV
Vehicle condition Wheel being rotated

OK:

The waveform is similar to that shown in the illustration.


HINT:

When the system is functioning normally, one wheel revolution generates 4 pulses. As the vehicle speed increases, the width indicated by (A) in the illustration narrows.




Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - COMBINATION METER ASSEMBLY)

NG

2.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - COMBINATION METER ASSEMBLY)
a.

Disconnect the G171 radio receiver assembly connector.


b.

Disconnect the G8 combination meter assembly connector.


c.

Disconnect the G33 body ECU connector.


d.

for 2TR-FE:

Disconnect the G142 ECM connector.


e.

for 2GD-FTV:

Disconnect the G49 ECM connector.


f.

for 2KD-FTV:

Disconnect the G140 ECM connector.


g.

w/ Smart Entry and Start System:

Disconnect the G16 certification ECU (smart key ECU assembly) connector.


h.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G171-17 (SPD) - G8-19 (+S) Always Below 1 Ω
G171-17 (SPD) or G8-19 (+S) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR