Before performing pre-disposal deployment of any SRS part, review and closely follow all applicable environmental and hazardous material regulations. Pre-disposal deployment may be considered hazardous material treatment.
Use the same procedure for RHD and LHD vehicles.
The procedures listed below are for RHD vehicles.
1. PRECAUTION
Do not perform this procedure indoors or on rough roads where safety cannot be ensured. Also, do not deploy SRS parts near residential areas.
If this procedure is performed indoors or on rough roads where safety cannot be ensured, unforeseen injuries may occur. Also, the deployment noise creates a nuisance to nearby residents.
When scrapping a vehicle equipped with an SRS or disposing of the instrument panel passenger airbag assembly, be sure to deploy the airbag first in accordance with the procedure described below. If any abnormality occurs with the airbag deployment, contact the Service Dept. of the distributor.
73960A
2.DISPOSE OF INSTRUMENT PANEL PASSENGER AIRBAG ASSEMBLY (When Installed in Vehicle)
When disposing of the instrument panel passenger airbag assembly, use an unneeded vehicle to deploy the airbag.
Be sure to observe the following procedure when deploying the airbag.
Prepare a battery as the power source to deploy the airbag.
Check the function of SST.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>STEERING PAD>DISPOSAL
Refer to Precaution.
for Type A:
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(for Type A)>PRECAUTION
for Type B:
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(for Type B)>PRECAUTION
Disconnect the cable from the negative (-) battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
If the airbag deploys for any reason, it may cause a serious accident.
Remove the combination meter assembly.
Click hereVehicle Interior>METER / GAUGE / DISPLAY>COMBINATION METER>REMOVAL
Disconnect the No. 2 instrument panel wire.
|
Slide in this Direction |
Pull and slide the lock slider in the direction indicated by the arrow to release the connector lock and disconnect the airbag connector.
When disconnecting any airbag connector, take care not to damage the airbag wire harness.
Install SST.
Connect the SST connector to the No. 2 instrument panel wire.
To avoid damaging the SST connector or wire harness, do not lock the secondary lock of the twin lock.
Do not place objects on top of the airbag door.
If deployed with an object on top of the airbag door, the door glass and windshield may break and fly off, causing serious injuries.
Do not deploy if the instrument panel passenger airbag assembly is loose.
If deployed while the instrument panel passenger airbag assembly is loose, the instrument panel passenger airbag assembly may fly off and cause serious injuries.
| *a | 10 m or more |
Move SST at least 10 m (32.8 ft.) away from the front side window of the vehicle.
While maintaining sufficient clearance for the SST wire harness in the front side window, close all doors and windows of the vehicle.
Do not deploy with all the doors and door windows open.
If deployed with all the doors and door windows open, dust and gas may enter the eyes or be breathed in.
Take care not to damage the SST wire harness.
Connect the red clip of SST to the positive (+) battery terminal and the black clip of SST to the negative (-) battery terminal.
Deploy the airbag.
Check that no one is inside the vehicle or within a 10 m (32.8 ft.) radius of the vehicle.
Press the SST activation switch and deploy the airbag.
Do not deploy with people inside or around the vehicle.
If deployed with people inside or around the vehicle, serious injuries may occur.
The airbag is deployed as the LED of the SST activation switch comes on.
Remove the instrument panel passenger airbag assembly.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>FRONT PASSENGER AIRBAG ASSEMBLY>REMOVAL
The instrument panel passenger airbag assembly becomes extremely hot when the airbag is deployed, so do not touch it for at least 30 minutes after deployment.
If not left alone for 30 minutes or more, burns may occur when touched.
Do not apply water etc. to an instrument panel passenger airbag assembly with a deployed airbag.
If water is applied to the instrument panel passenger airbag assembly immediately after deployment, burns may occur from the resulting steam.
Always wear safety glasses and gloves when handling a deployed instrument panel passenger airbag assembly.
If the instrument panel passenger airbag assembly is touched without wearing safety glasses and gloves, hot parts may cause burns and dust may enter the eyes.
After removal, quickly seal the instrument panel passenger airbag assembly in a plastic bag.
Dispose of the instrument panel passenger airbag assembly.
Place the instrument panel passenger airbag assembly in a plastic bag, tie it tightly and dispose of it according to local regulations.
The instrument panel passenger airbag assembly becomes extremely hot when the airbag is deployed, so do not touch it for at least 30 minutes after deployment.
If not left alone for 30 minutes or more, burns may occur when touched.
Do not apply water etc. to an instrument panel passenger airbag assembly with a deployed airbag.
If water is applied to the instrument panel passenger airbag assembly immediately after deployment, burns may occur from the resulting steam.
Always wear safety glasses and gloves when handling a deployed instrument panel passenger airbag assembly.
If the instrument panel passenger airbag assembly is touched without wearing safety glasses and gloves, hot parts may cause burns and dust may enter the eyes.
Never dispose of an instrument panel passenger airbag assembly with an undeployed airbag.
If an undeployed instrument panel passenger airbag assembly is disposed of, and then deploys for any reason, unforeseen injuries may occur.
Always wash your hands with water after completing the operation.
73960A
3.DISPOSE OF INSTRUMENT PANEL PASSENGER AIRBAG ASSEMBLY (When not Installed in Vehicle)
Be sure to observe the following procedure when deploying the airbag.
Prepare a battery as the power source to deploy the airbag.
Check the function of SST.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>STEERING PAD>DISPOSAL
Remove the instrument panel passenger airbag assembly.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>FRONT PASSENGER AIRBAG ASSEMBLY>REMOVAL
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
If the airbag deploys for any reason, it may cause a serious accident.
Install SST.
After connecting the following SST to each other, connect them to the instrument panel passenger airbag assembly.
| *a | Wire Diameter |
| *b | Stripped Wire |
Using braided wire, tie down the instrument panel passenger airbag assembly to an unneeded tire.
1.25 mm2 (0.0019 in.2) or more
If the wire harness is too thin or an alternative object is used to tie down the instrument panel passenger airbag assembly, it may snap when the airbag is deployed. Always use a wire for vehicle use with a cross-sectional area of at least 1.25 mm2 (0.0019 in.2).
To calculate the area of the cross-sectional area of stripped wire:
Area = 3.14 x (Diameter)2 / 4
Position the instrument panel passenger airbag assembly inside the tire with the airbag deployment side facing inside.
Must exceed the following dimensions
185 mm (7.28 in.)
360 mm (1.18 ft.)
| *a | Width | *b | Inner Diameter |
| *c | Deployment Side | - | - |
| *a | Remove looseness |
|
Deployment Side |
Do not install the instrument panel passenger airbag assembly with the deployment side facing outside.
When securing the instrument panel passenger airbag assembly, make sure there is no looseness in the wire harness.
If the deployment side is facing outside or the wire harness is loosely wrapped, the deployed instrument panel passenger airbag assembly and tire may fly off and cause serious injuries.
The tires may be damaged by the airbag deployment, so use unneeded tires.
Place the tires.
| *a | Tires (2 or more) |
Place at least 2 tires under the tire to which the instrument panel passenger airbag assembly is tied.
Place at least 2 tires onto the tire to which the instrument panel passenger airbag assembly is tied. The top tire should have a wheel installed.
Do not place the SST connector under the tire because it could be damaged.
The tires and wheel may be damaged by the airbag deployment, so use unneeded tires and wheels.
Tie the tires together with the 2 wires.
Install SST.
| *a | 10 m or more |
Connect the SST connector.
To avoid damaging the SST connector or wire harness, do not lock the secondary lock of the twin lock. Also, secure some slack for the SST wire harness inside the tire.
Move SST at least 10 m (32.8 ft.) away from the airbag tied down to the tire.
Deploy the airbag.
Connect the red clip of SST to the positive (+) battery terminal and the black clip of SST to the negative (-) battery terminal.
Check that no one is within a 10 m (32.8 ft.) radius of the wheel to which the instrument panel passenger airbag assembly is tied.
Press the SST activation switch and deploy the airbag.
Do not deploy with people around the tire.
If deployed with people around the tire, serious injuries may occur.
The airbag is deployed as the LED of the SST activation switch comes on.
Dispose of the instrument panel passenger airbag assembly.
The instrument panel passenger airbag assembly becomes extremely hot when the airbag is deployed, so do not touch it for at least 30 minutes after deployment.
If not left alone for 30 minutes or more, burns may occur when touched.
Do not apply water etc. to an instrument panel passenger airbag assembly with a deployed airbag.
If water is applied to the instrument panel passenger airbag assembly immediately after deployment, burns may occur from the resulting steam.
Always wear safety glasses and gloves when handling a deployed instrument panel passenger airbag assembly.
If the instrument panel passenger airbag assembly is touched without wearing safety glasses and gloves, hot parts may cause burns and dust may enter the eyes.
Never dispose of an instrument panel passenger airbag assembly with an undeployed airbag.
If an undeployed instrument panel passenger airbag assembly is disposed of, and then deploys for any reason, unforeseen injuries may occur.
Always wash your hands with water after completing the operation.
Remove the instrument panel passenger airbag assembly from the wheel.
Place the instrument panel passenger airbag assembly in a plastic bag, tie it tightly and dispose of it according to local regulations.