Home › Vehicle Exterior › LIGHTING (EXT) › STOP LIGHT SWITCH › from 2016.01
RM3270E _59 Vehicle Exterior _041720 LIGHTING (EXT) _0199683 STOP LIGHT SWITCH G

LIGHTING (EXT)  STOP LIGHT SWITCH  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 84340 1.INSPECT STOP LIGHT SWITCH ASSEMBLY

a.
E233306C35
1.49,0.271 1.865,0.479 0.375,0.208 1.292,1.167 1.042,1.854 true 2.281,1.115 2.656,0.958 true 2.063,1.188 2.146,1.865 true 0.115,0.104 0.344,0.271 0.229,0.167 10 false *a 1.563,0.292 1.99,0.51 0.427,0.219 10 false A64 2.708,0.875 2.875,1.042 0.167,0.167 10 false B 0.906,1.896 1.417,2.135 0.51,0.24 10 false GND 2.115,1.896 2.281,2.063 0.167,0.167 10 false B
*a Front view of wire harness connector
(to Stop Light Switch Assembly)


Disconnect the stop light switch assembly connector.


b.

Measure the voltage and resistance on the wire harness side connector according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A64-7 (B) - A64-2 (GND) Always 11 to 14 V
A64-6 (B) - A64-2 (GND) Engine switch on (IG) 11 to 14 V


Standard Resistance:
Tester Connection Condition Specified Condition
A64-2 (GND) - Body ground Always Below 1 Ω


If the result is not as specified, repair or replace the wire harness or connector.


c.

Reconnect the stop light switch assembly connector.


d.
E233300C21
1.521,0.271 1.854,0.51 0.333,0.24 1.927,1.115 2.406,1.677 true 2.073,1.063 2.531,0.76 true 1.813,1.115 1.99,1.677 true 1.688,1.115 1.167,1.677 true 1.323,0.604 1.552,1.073 true 0.188,0.115 0.417,0.281 0.229,0.167 10 false *a 1.573,0.302 2.021,0.563 0.448,0.26 10 false A64 2.583,0.677 3.031,0.896 0.448,0.219 10 false OUT 2,1.708 2.313,1.917 0.313,0.208 10 false L 2.302,1.698 2.802,1.917 0.5,0.219 10 false GND 1,1.698 1.448,1.958 0.448,0.26 10 false ACC 1.271,0.448 1.583,0.656 0.313,0.208 10 false L
*a Component with harness connected
(Stop Light Switch Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A64- 1 (OUT) - A64-2 (GND) Brake pedal not depressed 0 to 1.5 V
A64-1 (OUT) - A64-2 (GND) Brake pedal depressed 7.5 to 14 V
A64-3 (L) - A64-2 (GND) Brake pedal not depressed 7.5 to 14 V
A64-3 (L) - A64-2 (GND) Brake pedal depressed 0 to 1.5 V
A64-4 (ACC) - A64-2 (GND) Engine switch on (IG) 11 to 14 V
A64-5 (L) - A64-2 (GND) Engine switch on (IG), brake pedal depressed 0 to 1.5 V
A64-5 (L) - A64-2 (GND) Engine switch on (IG), brake pedal not depressed 7.5 to 14 V


If the result is not as specified, replace the stop light switch assembly.