Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System) › from 2016.01
RM3270E _58 Vehicle Interior _041713 HEATING / AIR CONDITIONING _0205064 AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System) J

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System)  IG Power Source Circuit  


DESCRIPTION

The main power source is supplied to the air conditioning amplifier assembly when the ignition switch is ON.

The power is used for operating the air conditioning amplifier assembly, servo motors, etc.

WIRING DIAGRAM

E315724E12
5.083,1.74 5.542,1.938 0.458,0.198 10 false G37 5.083,1.906 6.646,2.354 1.563,0.448 10 false Air Conditioning Amplifier Assembly 5.563,0.563 6.021,0.76 0.458,0.198 10 false IG+ 5.563,1.281 6.021,1.479 0.458,0.198 10 false GND 5.229,1.167 5.688,1.365 0.458,0.198 10 false 14 5.292,0.469 5.75,0.667 0.458,0.198 10 false 1 3.99,0.74 4.948,1.021 0.958,0.281 10 false IG1 NO.4 0.156,0.563 2.833,0.792 2.677,0.229 10 false from Ignition Switch*1, IG1 NO.1 Relay*2 0.198,2.104 2.875,2.333 2.677,0.229 10 false *1: w/o Smart Entry and Start System 0.198,2.417 2.875,2.646 2.677,0.229 10 false *2: w/ Smart Entry and Start System

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER ASSEMBLY - BATTERY AND BODY GROUND)
a.
E269948C22
1.448,0.333 1.958,0.583 0.51,0.25 3.01,0.823 2.76,0.823 2.76,0.823 2.656,1.25 true 0.927,0.479 1.177,0.479 1.177,0.479 1.375,1.26 true 0.042,0.052 0.354,0.25 0.313,0.198 10 false *a 1.573,0.375 1.885,0.573 0.313,0.198 10 false G37 3.073,0.75 3.406,0.948 0.333,0.198 10 false IG+ 0.594,0.417 1.104,0.604 0.51,0.188 10 false GND
*a Rear view of wire harness connector
(to Air Conditioning Amplifier Assembly)


Disconnect the air conditioning amplifier assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G37-14 (GND) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G37-1 (IG+) - Body ground Ignition switch off Below 1 V
G37-1 (IG+) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR