Home › Vehicle Interior › DOOR LOCK › WIRELESS DOOR LOCK CONTROL SYSTEM(w/ Smart Entry and Start System) › from 2016.01
RM3270E _58 Vehicle Interior _041705 DOOR LOCK _0198096 WIRELESS DOOR LOCK CONTROL SYSTEM(w/ Smart Entry and Start System) U

DOOR LOCK  WIRELESS DOOR LOCK CONTROL SYSTEM(w/ Smart Entry and Start System)  TERMINALS OF ECU  


CHECK INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY AND BODY ECU


E317657C19
0.594,3.865 0.927,4.104 0.333,0.24 1.99,3.865 2.323,4.104 0.333,0.24 3.458,3.865 3.792,4.104 0.333,0.24 4.844,3.865 5.177,4.104 0.333,0.24 6.198,3.865 6.531,4.104 0.333,0.24 1.969,5.063 2.302,5.302 0.333,0.24 3.333,5.063 3.667,5.302 0.333,0.24 4.729,5.063 5.063,5.302 0.333,0.24 6.198,5.063 6.531,5.302 0.333,0.24 0.604,6.448 0.938,6.688 0.333,0.24 1.938,6.448 2.271,6.688 0.333,0.24 3.375,6.448 3.708,6.688 0.333,0.24 4.833,6.448 5.167,6.688 0.333,0.24 6.208,6.438 6.542,6.677 0.333,0.24 3.344,7.708 3.677,7.948 0.333,0.24 0.552,4.854 0.896,5.042 0.344,0.188 0.552,5.104 0.896,5.292 0.344,0.188 0.104,0.052 0.417,0.292 0.313,0.24 12 false *1 0.75,0.938 1.063,1.135 0.313,0.198 10 false 2L 0.729,1.281 1.042,1.479 0.313,0.198 10 false 2M 0.74,1.667 1.052,1.865 0.313,0.198 10 false 2D 0.74,2.031 1.052,2.229 0.313,0.198 10 false 2K 0.729,2.375 1.042,2.573 0.313,0.198 10 false 2C 0.625,3.01 1.115,3.219 0.49,0.208 10 false 2A(*A) 1.281,3.104 1.594,3.302 0.313,0.198 10 false 2B 3.333,0.896 3.49,1.094 0.156,0.198 10 false A 6.375,0.583 6.688,0.781 0.313,0.198 10 false 2Q 6.396,0.927 6.708,1.125 0.313,0.198 10 false 2J 6.385,1.281 6.698,1.479 0.313,0.198 10 false 2P 6.385,1.656 6.698,1.854 0.313,0.198 10 false 2N 6.385,2 6.698,2.198 0.313,0.198 10 false 2G 6.396,2.375 6.708,2.573 0.313,0.198 10 false 2H 5.865,2.927 6.177,3.125 0.313,0.198 10 false 2F 6.375,2.99 6.688,3.188 0.313,0.198 10 false 2E 0.698,3.906 1.01,4.104 0.313,0.198 10 false 2L 2.063,3.906 2.375,4.104 0.313,0.198 10 false 2M 3.552,3.896 3.865,4.094 0.313,0.198 10 false 2D 4.917,3.906 5.229,4.104 0.313,0.198 10 false 2K 6.271,3.906 6.594,4.125 0.323,0.219 10 false 2C 0.635,5.125 0.948,5.323 0.313,0.198 10 false 2R 2.042,5.094 2.354,5.292 0.313,0.198 10 false 2B 3.406,5.104 3.719,5.302 0.313,0.198 10 false 2Q 4.823,5.094 5.135,5.292 0.313,0.198 10 false 2J 6.292,5.104 6.604,5.302 0.313,0.198 10 false 2P 0.688,6.479 1,6.677 0.313,0.198 10 false 2N 2.021,6.479 2.333,6.677 0.313,0.198 10 false 2G 3.458,6.479 3.771,6.677 0.313,0.198 10 false 2H 4.927,6.479 5.24,6.677 0.313,0.198 10 false 2F 6.292,6.469 6.604,6.667 0.313,0.198 10 false 2E 3.469,7.74 3.625,7.938 0.156,0.198 10 false A 0.635,4.875 0.948,5.073 0.313,0.198 10 false 2A 0.958,4.865 1.271,5.063 0.313,0.198 10 false (*A) 0.979,5.115 1.292,5.313 0.313,0.198 10 false (*B) 0.625,3.188 1.135,3.365 0.51,0.177 10 false 2R(*B)
*A for RHD *B for LHD
*1 Instrument Panel Junction Block Assembly - -


E317658C11
2.24,3.344 2.625,3.583 0.385,0.24 4.563,3.344 4.948,3.583 0.385,0.24 0.125,0.073 0.438,0.365 0.313,0.292 12 false *1 5.76,1.531 6.219,1.729 0.458,0.198 10 false G34 5.76,2.021 6.219,2.219 0.458,0.198 10 false G33 2.313,3.385 2.771,3.583 0.458,0.198 10 false G34 4.625,3.385 5.083,3.583 0.458,0.198 10 false G33
*1 Body ECU - -


a.

Remove the body ECU from the instrument panel junction block assembly.

for LHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for LHD)>REMOVAL

for RHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for RHD)>REMOVAL


b.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connectors disconnected.


Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A-1 (GND) - Body ground - Ground Always Below 1 Ω
A-6 (BECU) - Body ground - Battery power supply Always 11 to 14 V
A-7 (IG) - Body ground - Ignition power supply Engine switch on (IG) 11 to 14 V
Engine switch off Below 1 V


c.

Install the body ECU to the instrument panel junction block assembly.

for LHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for LHD)>INSTALLATION

for RHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for RHD)>INSTALLATION


d.

Measure the voltage and check for pulses according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
2N-2 (ACT+) - Body ground LG - Body ground*1
LA-B - Body ground*2
Door lock motor lock drive output (all doors) Door control switch (power window regulator master switch assembly) or driver door key cylinder off Below 1 V
Door control switch (power window regulator master switch assembly) or driver door key cylinder locked 11 to 14 V
2N-3 (ACT-) - Body ground GR - Body ground*1
LA-W - Body ground*2
Door lock motor unlock drive output (all doors) Door control switch (power window regulator master switch assembly) or driver door key cylinder off Below 1 V
Door control switch (power window regulator master switch assembly) or driver door key cylinder unlocked 11 to 14 V
2Q-1 (DCTY) - Body ground B - Body ground Driver door courtesy light switch input Driver door open Below 1 V
Driver door closed Pulse generation
2Q-2 (ACTY) - Body ground Y - Body ground All door courtesy light switches input except driver door Except driver door open Below 1 V
Except driver door closed Pulse generation
2L-4 (DCTY) - Body ground R - Body ground Driver door courtesy light switch input Driver door open Below 1 V
Driver door closed Pulse generation
G33-2 (LSWP) - Body ground Y - Body ground Except driver door unlock detection switch input Except driver door unlocked Below 1 V
Except driver door locked Pulse generation
G33-6 (HAZ) - Body ground SB - Body ground Hazard warning signal output Answer-back off 11 to 14 V
Answer-back on Below 1 V
G33-9 (PRG) - Body ground V - Body ground Signal output to certification ECU (smart key ECU assembly)
Procedure:
1.

Engine switch off

2.

All doors locked

3.

10 seconds elapsed after all doors locked

4.

Electrical key transmitter sub-assembly unlock switch not pressed


11 to 14 V
Procedure:
1.

Engine switch off

2.

All doors locked

3.

10 seconds elapsed after all doors locked

4.

Electrical key transmitter sub-assembly unlock switch pressed


Pulse generation
G33-14 (PCTY) - Body ground LG - Body ground Front passenger door courtesy light switch input Front passenger door open Below 1 V
Front passenger door closed Pulse generation
G33-15 (LSWD) - Body ground R - Body ground Driver door unlock detection switch input Driver door unlocked Below 1 V
Driver door locked Pulse generation
G33-16 (RDA) - Body ground W - Body ground Signal input from certification ECU (smart key ECU assembly)
Procedure:
1.

Engine switch off

2.

All doors locked

3.

10 seconds elapsed after all doors locked

4.

Electrical key transmitter sub-assembly unlock switch not pressed


11 to 14 V
Procedure:
1.

Engine switch off

2.

All doors locked

3.

10 seconds elapsed after all doors locked

4.

Electrical key transmitter sub-assembly unlock switch pressed


Pulse generation

*1: w/ Door Control Battery

*2: w/o Door Control Battery




CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)


B391999N03
2.281,0.583 2.781,0.833 0.5,0.25 4.052,0.583 4.552,0.833 0.5,0.25 2.396,0.635 2.854,0.833 0.458,0.198 10 false G16 4.167,0.635 4.625,0.833 0.458,0.198 10 false G17

a.

Disconnect the G16 and G17 certification ECU (smart key ECU assembly) connectors.


b.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connectors disconnected.


Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G16-1 (+B) - Body ground P - Body ground Battery power supply Always 11 to 14 V
G16-10 (E) - Body ground BR - Body ground Ground Always Below 1 Ω
G17-33 (CUTB) - Body ground W - Body ground Dark current cut fuse pin input signal* Always 11 to 14 V

*: In order to prevent the vehicle battery from being depleted when the vehicle is shipped long distances, a fuse that cuts unnecessary electrical load while the vehicle is being shipped is set in the circuit. If the fuse is removed, the circuit becomes open. If the fuse that is between the vehicle battery and terminal CUTB is removed and the circuit is open, the certification ECU (smart key ECU assembly) changes to a certain control mode.



c.

Reconnect the G16 and G17 certification ECU (smart key ECU assembly) connectors.


d.

Measure the voltage and check for pulses according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G16-2 (BZR) - Body ground SB - Body ground Wireless door lock buzzer signal Wireless door lock buzzer off Below 1 V
Wireless door lock buzzer on Pulse generation
G17-3 (RCO) - G16-10 (E) G - BR Wireless tuner power supply output circuit
Procedure:
1.

Engine switch off

2.

Electrical key transmitter sub-assembly brought outside vehicle

3.

Lock or unlock button of electrical key transmitter sub-assembly not pressed → pressed


Pulse generation (See waveform 1)
G16-9 (LSWP) - G16-10 (E) L - BR Except driver door unlock detection switch input
Procedure:
1.

Engine switch off

2.

All doors closed

3.

All doors unlocked

4.

Lock button of electrical key transmitter sub-assembly not pressed


Below 1 V
Procedure:
1.

Engine switch off

2.

All doors closed

3.

All doors unlocked

4.

Lock button of electrical key transmitter sub-assembly pressed


8.5 V or higher
G16-13 (RDA3) - G16-10 (E) W - BR Signal output to body ECU
Procedure:
1.

Engine switch off

2.

All doors locked

3.

10 seconds elapsed after all doors locked

4.

Electrical key transmitter sub-assembly unlock switch not pressed


11 to 14 V
Procedure:
1.

Engine switch off

2.

All doors locked

3.

10 seconds elapsed after all doors locked

4.

Electrical key transmitter sub-assembly unlock switch pressed


Pulse generation
G17-21 (CSEL) - G16-10 (E) P - BR Communication channel switching circuit
Procedure:
1.

Engine switch off

2.

All doors closed


Pulse generation (See waveform 2)
G17-22 (RDAS) - G16-10 (E) L - BR Door control receiver verifies data received from electrical key transmitter sub-assembly. Door control receiver sends data to ECU and intermittently grounds 12 V signal from certification ECU (smart key ECU assembly).
Procedure:
1.

Engine switch off

2.

All doors locked

3.

Lock or unlock button of electrical key transmitter sub-assembly not pressed → pressed


Pulse generation (See waveform 3)
G17-36 (PRG3) - G16-10 (E) V - BR Signal input from body ECU
Procedure:
1.

Engine switch off

2.

All doors locked

3.

10 seconds elapsed after all doors locked

4.

Electrical key transmitter sub-assembly unlock switch not pressed


11 to 14 V
Procedure:
1.

Engine switch off

2.

All doors locked

3.

10 seconds elapsed after all doors locked

4.

Electrical key transmitter sub-assembly unlock switch pressed


Pulse generation


e.
B251178C19
0.198,1 0.531,1.198 0.333,0.198 10 GND 1.01,1.885 1.198,2.042 0.188,0.156 10 *a 2.021,1.885 2.208,2.042 0.188,0.156 10 *b
*a Before lock or unlock button of electrical key transmitter sub-assembly pressed
*b After lock or unlock button of electrical key transmitter sub-assembly pressed


Using an oscilloscope, check waveform 1.

HINT:

The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


Waveform 1 (Reference)
Item Content
Tester Connection G17-3 (RCO) - G16-10 (E)
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Procedure:
1.

Engine switch off

2.

Electrical key transmitter sub-assembly brought outside vehicle

3.

Lock or unlock button of electrical key transmitter sub-assembly not pressed → pressed




f.
B348666E01
0.177,1 0.635,1.198 0.458,0.198 10 false GND

Using an oscilloscope, check waveform 2.

HINT:

The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


Waveform 2 (Reference)
Item Content
Tester Connection G17-21 (CSEL) - G16-10 (E)
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition
Procedure:
1.

Engine switch off

2.

All doors closed




g.
B251177C18
0.208,1 0.542,1.198 0.333,0.198 10 GND 1.021,1.896 1.208,2.052 0.188,0.156 10 *a 2.188,1.906 2.375,2.063 0.188,0.156 10 *b
*a Before lock or unlock button of electrical key transmitter sub-assembly pressed
*b After lock or unlock button of electrical key transmitter sub-assembly pressed


Using an oscilloscope, check waveform 3.

HINT:

The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


Waveform 3 (Reference)
Item Content
Tester Connection G17-22 (RDAS) - G16-10 (E)
Tool Setting 5 V/DIV., 500 ms./DIV.
Condition
Procedure:
1.

Engine switch off

2.

All doors locked

3.

Lock or unlock button of electrical key transmitter sub-assembly not pressed → pressed