| Part Tightened | N*m | kgf*cm | ft.*lbf | in.*lbf | |||
|---|---|---|---|---|---|---|---|
| Camshaft bearing cap (for Bank 1) x Cylinder head LH | for bolt A | 9.0 | 92 | 80 | |||
| for bolt B | 24 | 245 | 18 | ||||
| Camshaft timing gear assembly x No. 3 camshaft sub-assembly | 100 | 1020 | 74 | ||||
| No. 3 chain tensioner assembly x Cylinder head LH | 21 | 214 | 15 | ||||
| No. 4 camshaft sub-assembly x Camshaft timing sprocket | 100 | 1020 | 74 | ||||
| Camshaft bearing cap (for Bank 2) x Cylinder head sub-assembly | for bolt A | 9.0 | 92 | 80 | |||
| for bolt B | 24 | 245 | 18 | ||||
| Camshaft timing gear assembly x Camshaft | 100 | 1020 | 74 | ||||
| No. 2 chain tensioner x Cylinder head sub-assembly | 21 | 214 | 15 | ||||
| No. 2 camshaft x Camshaft timing sprocket | 100 | 1020 | 74 | ||||
| Timing chain cover plate x Timing chain cover sub-assembly | 9.1 | 93 | 81 | ||||
| Part Tightened | N*m | kgf*cm | ft.*lbf | in.*lbf | |||
|---|---|---|---|---|---|---|---|
| Cylinder head sub-assembly x Cylinder block | 1st | 36 | 367 | 27 | |||
| 2nd | Turn 180° | ||||||
| Cylinder head LH x Cylinder block (for cylinder head set bolt) | 1st | 36 | 367 | 27 | |||
| 2nd | Turn 180° | ||||||
| Cylinder head LH x Cylinder block (except cylinder head set bolt) | 30 | 306 | 22 | ||||
| Part Tightened | N*m | kgf*cm | ft.*lbf | |||
|---|---|---|---|---|---|---|
| Drive plate and ring gear sub-assembly x Crankshaft | 83 | 846 | 61 | |||
| Part Tightened | N*m | kgf*cm | ft.*lbf | in.*lbf | |||
|---|---|---|---|---|---|---|---|
| Engine hanger x Cylinder head | 33 | 337 | 24 | ||||
| Engine assembly x Body | 42 | 428 | 31 | ||||
| Water hose sub-assembly x Cylinder head cover sub-assembly LH | 5.4 | 55 | 48 | ||||
| Engine wire x Engine room relay block | 12.5 | 127 | 9 | ||||
| No. 2 engine wire x Body | 14 | 143 | 10 | ||||
| Battery hold down clamp | 5.4 | 55 | 48 | ||||
| Positive (+) battery terminal | 5.35 | 55 | 47 | ||||
| Engine room main wire x Battery positive cable | 7.55 | 77 | 67 | ||||
| Engine wire x Body | 7.55 | 77 | 67 | ||||
| Vane pump assembly x Timing chain cover sub-assembly | 21 | 214 | 15 | ||||
| Air cleaner case sub-assembly x Body | 6.0 | 61 | 53 | ||||
| No. 3 engine under cover sub-assembly | 28 | 286 | 21 | ||||
| No. 2 engine under cover sub-assembly | 28 | 286 | 21 | ||||
| No. 1 engine under cover sub-assembly | for M6 bolt | 11.5 | 117 | 8 | |||
| for M8 bolt | 28 | 286 | 21 | ||||
| Hood sub-assembly x Hood hinge assembly | 13 | 133 | 10 | ||||
| Part Tightened | N*m | kgf*cm | ft.*lbf | in.*lbf | |||
|---|---|---|---|---|---|---|---|
| Stud bolt x Oil pan sub-assembly | 4.0 | 41 | 35 | ||||
| Stud bolt x Timing chain cover sub-assembly | 10 | 102 | 7 | ||||
| Stud bolt x Cylinder head cover sub-assembly | 6.0 | 61 | 53 | ||||
| Taper screw plug x Cylinder block | 25 | 255 | 18 | ||||
| V-bank cover bracket sub-assembly x Cylinder head cover sub-assembly | 10 | 102 | 7 | ||||
| No. 1 water outlet pipe x Cylinder block | 10 | 102 | 7 | ||||
| Camshaft bearing cap (for Bank 2) x Cylinder head sub-assembly | for bolt A | 9.0 | 92 | 80 | |||
| for bolt B | 24 | 245 | 18 | ||||
| Camshaft bearing cap (for Bank 1) x Cylinder head LH | for bolt A | 9.0 | 92 | 80 | |||
| for bolt B | 24 | 245 | 18 | ||||
| No. 3 chain tensioner assembly x Cylinder head LH | 21 | 214 | 15 | ||||
| Camshaft timing gear assembly x No. 3 camshaft sub-assembly | 100 | 1020 | 74 | ||||
| Camshaft timing sprocket x No. 4 camshaft sub-assembly | 100 | 1020 | 74 | ||||
| No. 2 chain tensioner x Cylinder head sub-assembly | 21 | 214 | 15 | ||||
| Camshaft timing gear assembly x Camshaft | 100 | 1020 | 74 | ||||
| Camshaft timing sprocket x No. 2 camshaft | 100 | 1020 | 74 | ||||
| No. 1 chain vibration damper x Cylinder head LH and cylinder block | 19 | 194 | 14 | ||||
| No. 1 chain tensioner assembly x Cylinder head sub-assembly | 10 | 102 | 7 | ||||
| No. 2 idle gear shaft x Cylinder block | 60 | 612 | 44 | ||||
| Engine water pump assembly x Timing chain cover sub-assembly | 11 | 112 | 8 | ||||
| Engine rear oil seal retainer x Cylinder block | for nut | 9.0 | 92 | 80 | |||
| for bolt | 10 | 102 | 7 | ||||
| Oil pan drain plug x No. 2 oil pan sub-assembly | 40 | 408 | 30 | ||||
| Cylinder head cover sub-assembly LH x Oil filler cap housing | 9.0 | 92 | 80 | ||||
| Rear water by-pass joint x Cylinder head LH and cylinder head sub-assembly | for bolt | 10 | 102 | 7 | |||
| for nut | 9.0 | 92 | 80 | ||||
| Union x Cylinder head LH and cylinder head sub-assembly | 62 | 632 | 46 | ||||
| Cylinder block water drain cock sub-assembly x Cylinder block | 25 | 255 | 18 | ||||
| Cylinder block water drain cock plug x Cylinder block water drain cock sub-assembly | 12.7 | 130 | 9 | ||||
| No. 1 idler pulley sub-assembly x Timing chain cover sub-assembly | 54 | 551 | 40 | ||||
| Engine oil level dipstick guide x Oil pan sub-assembly | 9.0 | 92 | 80 | ||||
| V-ribbed belt tensioner assembly x Timing chain cover sub-assembly | 36 | 367 | 27 | ||||
| Front No. 1 engine mounting bracket LH x Cylinder block | 43 | 438 | 32 | ||||
| Front No. 1 engine mounting bracket RH x Cylinder block | 43 | 438 | 32 | ||||
| No. 1 fuel pipe sub-assembly and No. 2 fuel pipe sub-assembly x Cylinder head cover sub-assembly LH | 9.0 | 92 | 80 | ||||
| Part Tightened | N*m | kgf*cm | ft.*lbf | |||
|---|---|---|---|---|---|---|
| Union x Cylinder head sub-assembly and cylinder head LH | 14.7 | 150 | 11 | |||
| No. 1 straight screw plug x Cylinder head sub-assembly and cylinder head LH | 80 | 816 | 59 | |||
| No. 2 straight screw plug x Cylinder head sub-assembly and cylinder head LH | 85 | 867 | 63 | |||
| Part Tightened | N*m | kgf*cm | ft.*lbf | in.*lbf | |||
|---|---|---|---|---|---|---|---|
| No. 1 oil nozzle sub-assembly x Cylinder block | 9.0 | 92 | 80 | ||||
| Crankshaft bearing cap x Cylinder block | Quantity: 16 | 1st | 61 | 622 | 45 | ||
| 2nd | Turn 90° | ||||||
| Crankshaft bearing cap x Cylinder block | Quantity: 8 | 25.7 | 262 | 19 | |||
| Connecting rod cap x Connecting rod | 1st | 24.5 | 250 | 18 | |||
| 2nd | Turn 90° | ||||||