Home › Vehicle Interior › HEATING / AIR CONDITIONING › COMPRESSOR(for 1KD-FTV, 2KD-FTV) › from 2016.08
RM3270E _58 Vehicle Interior _041713 HEATING / AIR CONDITIONING _0234826 COMPRESSOR(for 1KD-FTV, 2KD-FTV) A

HEATING / AIR CONDITIONING  COMPRESSOR(for 1KD-FTV, 2KD-FTV)  REASSEMBLY  


PROCEDURE

Hide 88410 1.INSTALL MAGNET CLUTCH ASSEMBLY

a.
E320435

Clamp the compressor assembly in a vise between aluminum plates.


b.

Install the magnet clutch stator with the parts aligned as shown in the illustration.


c.
E320436C01
0.76,0.458 1.073,0.615 0.313,0.156 10 false *a 0.26,0.51 0.573,0.667 0.313,0.156 10 false *b 1.188,0.521 1.5,0.677 0.313,0.156 10 false *c
*a Chamfered Side
*b Inside
*c Outside


Using a snap ring expander, install a new snap ring with the chamfered side facing outward.

NOTICE:

When installing the snap ring, do not widen it excessively.



d.
E320437C01
0.729,0.417 1.042,0.573 0.313,0.156 10 false *a 0.271,0.469 0.583,0.625 0.313,0.156 10 false *b 1.167,0.469 1.479,0.625 0.313,0.156 10 false *c
*a Chamfered Side
*b Inside
*c Outside


Using a snap ring expander, install the magnet clutch rotor and a new snap ring with the chamfered side facing outward.

NOTICE:
·

Do not damage the seal cover of the bearing when installing the snap ring.

·

When installing the snap ring, do not widen it excessively.




e.

Install the magnet clutch washer(s) and magnet clutch hub.

NOTICE:

Do not change the combination of the magnet clutch washer(s) used before disassembly.



f.
E320438C01
1.073,0.406 1.313,0.406 false 1.365,0.333 1.677,0.49 0.313,0.156 10 false *a
*a SST


Using SST, hold the magnet clutch hub and install the bolt.

SST
09985-00040  

Torque:
13.2 N*m (135 kgf*cm, 10 ft.*lbf)

NOTICE:

Make sure that there is no foreign matter or oil on the compressor shaft, bolt and magnet clutch hub.



Hide 2.INSPECT MAGNET CLUTCH CLEARANCE

a.
E320439

Set a dial indicator to the magnet clutch hub.


b.

Connect a battery positive lead to terminal 1 of the magnet clutch connector and a negative lead to the ground wire. Turn the magnet clutch on and off and measure the clearance.

Standard Clearance:

0.35 to 0.60 mm (0.0138 to 0.0236 in.)



c.

If the measured value is not within the standard clearance, remove the magnet clutch hub and adjust the clearance using magnet clutch washers to obtain the standard clearance.

Magnet Clutch Washer Thickness:

0.1 mm (0.0039 in.)

0.3 mm (0.0118 in.)

0.5 mm (0.0197 in.)


NOTICE:

Adjustment should be performed with 3 or fewer magnet clutch washers.



d.

Remove the compressor assembly with magnet clutch from the vise.


Hide 88688N 3.INSTALL COOLER BRACKET

a.
E320430

Install the cooler bracket with the screw.