Home › Suspension › TIRE PRESSURE MONITORING › TIRE PRESSURE WARNING SYSTEM › from 2016.08
RM3270E _53 Suspension _057740 TIRE PRESSURE MONITORING _0287816 TIRE PRESSURE WARNING SYSTEM C

TIRE PRESSURE MONITORING  TIRE PRESSURE WARNING SYSTEM  C2198/98  Initialization Switch (for Test Mode DTC)  


DESCRIPTION

During test mode, when the tire pressure warning reset switch is on, the tire pressure warning light comes on and when the tire pressure warning reset switch is off, the tire pressure warning light blinks at 0.125 second intervals.

DTC No. Detection Item DTC Detection Condition Trouble Area
C2198/98 Initialization Switch (for Test Mode DTC) Test mode procedure is performed.
·

Tire pressure warning reset switch

·

Wire harness or connector

·

Tire pressure warning ECU and receiver



WIRING DIAGRAM

C249283E41
5.063,2.969 6.823,3.375 1.76,0.406 10 false Tire Pressure Warning ECU and Receiver 1.885,1.563 4.271,1.844 2.385,0.281 10 false Tire Pressure Warning Reset Switch 1.885,1.354 2.365,1.521 0.479,0.167 10 false G150 2.292,0.875 2.396,1.052 0.104,0.177 10 false 1 3.427,0.875 3.531,1.052 0.104,0.177 10 false 4 5.073,2.771 6.115,2.927 1.042,0.156 10 false N54 5.229,0.844 5.344,1 0.115,0.156 10 false 7 5.448,1.021 5.885,1.177 0.438,0.156 10 false CLSW 2.51,0.865 2.708,1.083 0.198,0.219 10 false E 3.104,0.865 3.375,1.125 0.271,0.26 10 false INT

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the tire pressure warning ECU and receiver, read the transmitter IDs stored in the old ECU using the GTS and write them down before removal.

·

It is necessary to perform initialization Suspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>INITIALIZATION after registration Suspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>REGISTRATION of the transmitter IDs into the tire pressure warning ECU and receiver if the ECU has been replaced.



PROCEDURE

1.INSPECT TIRE PRESSURE WARNING RESET SWITCH
a.

Turn the ignition switch off.


b.

Remove the tire pressure warning reset switch.

Click hereSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING RESET SWITCH>REMOVAL


c.

Inspect the tire pressure warning reset switch.

Click hereSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING RESET SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (TIRE PRESSURE WARNING RESET SWITCH - TIRE PRESSURE WARNING ECU AND RECEIVER)

NG

REPLACE TIRE PRESSURE WARNING RESET SWITCH

2.CHECK HARNESS AND CONNECTOR (TIRE PRESSURE WARNING RESET SWITCH - TIRE PRESSURE WARNING ECU AND RECEIVER)
a.

Disconnect the G150 tire pressure warning reset switch connector.


b.

Disconnect the N54 tire pressure warning ECU and receiver connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N54-7 (CLSW) - G150-4 (INT) Always Below 1 Ω
N54-7 (CLSW) or G150-4 (INT) - Body ground Always 10 kΩ or higher
G150-1 (E) - Body ground Always Below 1 Ω


Result:
Proceed to
OK
NG




OK

REPLACE TIRE PRESSURE WARNING ECU AND RECEIVER

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR