Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › TOYOTA PARKING ASSIST-SENSOR SYSTEM › from 2016.08
RM3270E _56 Audio / Visual / Telematics _041701 PARK ASSIST / MONITORING _0197847 TOYOTA PARKING ASSIST-SENSOR SYSTEM J

PARK ASSIST / MONITORING  TOYOTA PARKING ASSIST-SENSOR SYSTEM  Reverse Signal Circuit  


DESCRIPTION

The clearance warning ECU assembly receives the reverse signal from the back-up light switch assembly*1 or park/neutral position switch assembly*2.

*1: for Manual Transmission

*2: for Automatic Transmission

WIRING DIAGRAM

E335839E06
0.063,0.542 1,0.76 0.938,0.219 10 false from IG1 Relay 1.813,0.729 2.417,0.938 0.604,0.208 10 false IG1 NO.1 3.052,0.458 3.167,0.625 0.115,0.167 10 false 2 4.573,0.469 4.719,0.625 0.146,0.156 10 false 1 5.344,0.563 5.552,0.729 0.208,0.167 10 false RL 5.115,0.458 5.292,0.615 0.177,0.156 10 false 21 4.885,1.854 5.188,2.01 0.302,0.156 10 false G88 4.885,2.031 7.063,2.24 2.177,0.208 10 false Clearance Warning ECU Assembly 2.844,0.896 3.146,1.063 0.302,0.167 10 false C11 2.833,1.052 4.865,1.25 2.031,0.198 10 false Back-up Light Switch Assembly 2.833,1.896 3.167,2.063 0.333,0.167 10 false C22 3.021,1.427 3.146,1.583 0.125,0.156 10 false 2 4.594,1.438 4.729,1.594 0.135,0.156 10 false 1 4.292,1.448 4.51,1.604 0.219,0.156 10 false RL 2.854,2.073 4.667,2.427 1.813,0.354 10 false Park/Neutral Position Switch Assembly 2.698,0.438 2.854,0.604 0.156,0.167 10 false *1 2.688,1.427 2.865,1.583 0.177,0.156 10 false *2 0.073,2.469 1.979,2.656 1.906,0.188 10 false *2: for Automatic Transmission 0.073,2.219 1.813,2.375 1.74,0.156 10 false *1: for Manual Transmission 3.219,1.438 3.51,1.594 0.292,0.156 10 false RB

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (CLEARANCE WARNING ECU ASSEMBLY - BATTERY)
a.
B409698C01
0.167,1.063 0.667,1.313 0.5,0.25 0.875,1.906 1.208,1.906 1.208,1.906 1.406,1.292 true 0.271,1.104 0.729,1.302 0.458,0.198 10 false G88 0.063,0.031 0.521,0.229 0.458,0.198 10 false *a 0.656,1.823 1.115,2.021 0.458,0.198 10 false RL
*a Rear view of wire harness connector
(to Clearance Warning ECU Assembly)


Disconnect the clearance warning ECU assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G88-21 (RL) - Body ground
·

Ignition switch ON

·

Shift lever in R


11 to 14 V
G88-21 (RL) - Body ground
·

Ignition switch ON

·

Shift lever in any position other than R


Below 1 V



Result:
Proceed to
OK
NG (for Manual Transmission)
NG (for Automatic Transmission)



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG (for Manual Transmission)

2.INSPECT BACK-UP LIGHT SWITCH ASSEMBLY

NG (for Automatic Transmission)

4.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY
2.INSPECT BACK-UP LIGHT SWITCH ASSEMBLY

OK

3.CHECK HARNESS AND CONNECTOR (BACK-UP LIGHT SWITCH ASSEMBLY - CLEARANCE WARNING ECU ASSEMBLY AND BATTERY)

NG

3.CHECK HARNESS AND CONNECTOR (BACK-UP LIGHT SWITCH ASSEMBLY - CLEARANCE WARNING ECU ASSEMBLY AND BATTERY)
a.

Disconnect the G88 clearance warning ECU assembly connector.


b.

Disconnect the C11 back-up light switch assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G88-21 (RL) - C11-1 Always Below 1 Ω
G88-21 (RL) or C11-1 - Body ground Always 10 kΩ or higher



d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C11-2 - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY

OK

5.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - CLEARANCE WARNING ECU ASSEMBLY AND BATTERY)

NG

5.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - CLEARANCE WARNING ECU ASSEMBLY AND BATTERY)
a.

Disconnect the G88 clearance warning ECU assembly connector.


b.

Disconnect the C22 park/neutral position switch assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G88-21 (RL) - C22-1 (RL) Always Below 1 Ω
G88-21 (RL) or C22-1 (RL) - Body ground Always 10 kΩ or higher



d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C22-2 (RB) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR