Home › Engine / Hybrid System › 1GD-FTV EMISSION CONTROL › EGR VALVE › from 2016.08
RM3270E _51 Engine / Hybrid System _041674 1GD-FTV EMISSION CONTROL _0206563 EGR VALVE A

1GD-FTV EMISSION CONTROL  EGR VALVE  INSTALLATION  


PROCEDURE

Hide 25630 1.INSTALL NO. 2 EGR VALVE ASSEMBLY

a.

Using an E8 "TORX" socket wrench, install the 4 stud bolts to the No. 2 EGR valve assembly.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


b.

Install a new gasket and the No. 2 EGR valve assembly to the No. 1 EGR cooler with the 4 bolts.

Torque:
25 N*m (255 kgf*cm, 18 ft.*lbf)


Hide 25624 2.INSTALL EGR VALVE ADAPTER

a.

Install a new gasket and the EGR valve adapter to the No. 2 EGR valve assembly with the 2 bolts.

Torque:
25 N*m (255 kgf*cm, 18 ft.*lbf)


Hide 3.INSTALL NO. 1 EGR COOLER AND NO. 2 EGR VALVE ASSEMBLY

a.

Temporarily install the No. 1 EGR cooler and No. 2 EGR valve assembly to the intake manifold with the 4 bolts.


b.
A343906N01
0.844,1.875 0.99,2.063 0.146,0.188 10 true 1 2.167,1.76 2.313,1.948 0.146,0.188 10 true 2 3.083,0.667 3.229,0.854 0.146,0.188 10 true 3 0.5,0.115 0.646,0.302 0.146,0.188 10 true 4

Tighten the 4 bolts in the order shown in the illustration.

NOTICE:

Make sure to tighten the bolts in the order.


Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


Hide 25601 5.INSTALL NO. 1 EGR PIPE SUB-ASSEMBLY

a.

Using an E8 "TORX" socket wrench, install 2 new stud bolts to the exhaust manifold.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


b.

Install 2 new gaskets and the No. 1 EGR pipe sub-assembly to the exhaust manifold and EGR valve adapter with 4 new nuts.

Torque:
29 N*m (296 kgf*cm, 21 ft.*lbf)


c.

Connect the No. 1 EGR pipe sub-assembly to the vacuum transmitting pipe sub-assembly with the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 16209 6.CONNECT NO. 4 WATER BY-PASS PIPE SUB-ASSEMBLY

a.

Connect the No. 4 water by-pass pipe sub-assembly to the intake manifold with the 2 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


b.

Connect the water hose to the No. 2 EGR valve assembly, and slide the clamp to secure the hose.


c.

Connect the No. 7 water by-pass hose to the No. 1 EGR cooler, and slide the clamp to secure the hose.


Hide 16206B 7.INSTALL NO. 3 WATER BY-PASS PIPE SUB-ASSEMBLY

a.

Install the No. 3 water by-pass pipe sub-assembly to the No. 1 EGR cooler with the 2 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


b.

Connect the No. 8 water by-pass hose to the No. 3 water by-pass pipe sub-assembly, and slide the clamp to secure the hose.


c.

Connect the No. 4 fuel hose to the No. 3 water by-pass pipe sub-assembly.


Hide 25800 8.INSTALL ELECTRIC EGR CONTROL VALVE ASSEMBLY

a.

Install a new gasket and the electric EGR control valve assembly to the No. 2 EGR valve assembly with the 2 bolts.

Torque:
25 N*m (255 kgf*cm, 18 ft.*lbf)


b.

Connect the No. 9 water by-pass hose to the electric EGR control valve assembly, and slide the clamp to secure the hose.


c.

Attach the clamp and connect the connector to the common rail assembly.


Hide 25612 9.INSTALL NO. 2 EGR PIPE

a.

Install 2 new gaskets and No. 2 EGR pipe to the electric EGR control valve assembly and the intake manifold with the 4 nuts.

Torque:
29 N*m (296 kgf*cm, 21 ft.*lbf)


Hide 25625 10.INSTALL EGR VALVE BRACKET

a.

Install the EGR valve bracket to the electric EGR control valve assembly and intake manifold with the bolt and nut.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


Hide 82121 11.CONNECT ENGINE WIRE

a.

Connect the connector to the vacuum control valve set.


b.

Attach the clamp and install the bolt.

Torque:
18.5 N*m (189 kgf*cm, 14 ft.*lbf)


c.

Attach the clamp and connect the connector to the power steering oil pressure switch.


d.

Attach the 2 clamps and install the bolt.

Torque:
12.5 N*m (127 kgf*cm, 9 ft.*lbf)


e.

Connect the connector to the sensor wire of the common rail assembly.


f.

Connect the connector to the glow plug connector.


g.

Connect the connector to the electric EGR control valve assembly.


h.

Connect the 4 connectors to the 4 injector assemblies.


i.

Connect the connector to the camshaft position sensor.


j.

Connect the connector to the exhaust fuel addition injector assembly.


k.

Connect the 3 connectors to the 3 exhaust gas temperature sensors.


l.

Connect the connector to the differential pressure sensor.


m.

Attach the 2 clamps and connect the 2 connectors to the turbocharger sub-assembly.


Hide 23300 12.CONNECT FUEL FILTER ASSEMBLY

a.

Connect the fuel filter assembly to the fuel filter support.


b.
A339641N01
2.792,1.646 3.01,1.823 0.219,0.177 10 true 1 3.083,0.969 3.302,1.146 0.219,0.177 10 true 2

Attach the clamp and slide the lead wire as shown in the illustration to install it.


Hide 12632 13.INSTALL NO. 2 ENGINE COVER BRACKET

a.

Install the No. 2 engine cover bracket to the No. 3 water by-pass pipe sub-assembly and No. 2 EGR valve assembly with the 2 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 44763C 14.INSTALL NO. 2 HOSE TO HOSE TUBE

a.

Install the No. 2 hose to hose tube to the cylinder head cover sub-assembly and hose bracket with the 2 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


b.

Connect the union to check valve hose to the vacuum pump assembly, and slide the clamp to secure the hose.


c.

Connect the union to connector tube hose to the No. 1 hose to hose tube, and slide the clamp to secure the hose.


Hide 89421C 15.INSTALL TURBO PRESSURE SENSOR

a.

Install the turbo pressure sensor to the No. 3 water by-pass pipe sub-assembly with the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


b.

Connect the connector to the turbo pressure sensor.


Hide 23265C 16.INSTALL GAS FILTER

a.

Install the gas filter to the gas filter bracket.


b.

Connect the 2 vacuum hoses to the turbo pressure sensor and intake manifold.


Hide 16278 17.INSTALL NO. 2 WATER BY-PASS PIPE

a.

Install the No. 2 water by-pass pipe to the cylinder head cover sub-assembly, No. 3 water by-pass pipe sub-assembly and No. 2 engine cover bracket with the 4 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


b.

Connect the No. 16 water by-pass hose to the No. 1 EGR cooler, and slide the clamp to secure the hose.


c.

Connect the 2 heater hoses to the No. 2 water by-pass pipe, and slide the 2 clamps to secure the 2 hoses.


d.

Connect the No. 15 water by-pass hose to the water by-pass pipe, and slide the clamp to secure the hose.


e.

Connect the No. 2 water by-pass pipe to the No. 13 water by-pass hose, and slide the clamp to secure the hose.


Hide 26100G 18.INSTALL DIESEL THROTTLE BODY ASSEMBLY