Home › Drivetrain › DRIVE SHAFT / PROPELLER SHAFT › PROPELLER SHAFT ASSEMBLY(for TMEE (AAV) Made) › from 2017.03
RM3270E _52 Drivetrain _041685 DRIVE SHAFT / PROPELLER SHAFT _0313534 PROPELLER SHAFT ASSEMBLY(for TMEE (AAV) Made) A

DRIVE SHAFT / PROPELLER SHAFT  PROPELLER SHAFT ASSEMBLY(for TMEE (AAV) Made)  INSTALLATION  


PROCEDURE

Hide 37100 1.INSTALL PROPELLER SHAFT WITH CENTER BEARING ASSEMBLY (for Pre-Runner)

a.

Completely remove any oil, etc. and clean the contact surfaces of the propeller shaft flange and differential flange.


b.

Align the matchmarks on the propeller shaft flange and differential flange.


c.

Install the propeller shaft to the extension housing.


d.

Temporarily install the center support bearing bracket with the 2 bolts. Tighten the bolts as much as possible by hand.


e.

Install the propeller shaft with center bearing assembly with the 4 nuts and 4 washers.

Torque:
88.2 N*m (899 kgf*cm, 65 ft.*lbf)


f.
C317901C02
1.802,0.323 2.135,0.323 true 2.177,1.917 2.427,1.917 false 1.563,0.229 1.823,0.438 0.26,0.208 10 true *a 2.583,1.844 2.896,2.042 0.313,0.198 10 true *b 2.521,0.354 2.979,0.552 0.458,0.198 10 true (A)
*a Center Bearing Housing Center Line
*b Center Bearing Center Line


Unload the vehicle and then make sure all 4 wheels are touching the ground and the vehicle is supporting all of its own weight. The center lines of the center bearing and center bearing housing (refer to the illustration) must be adjusted so that they are within 0 +/-1 mm (0 +/-0.0394 in.) of each other. Measure the difference along the front/rear axis of the vehicle.

Distance (A):

0 +/-1 mm (0 +/-0.0394 in.)



g.

Tighten the 2 bolts of the center support bearing bracket.

Torque:
36.2 N*m (369 kgf*cm, 27 ft.*lbf)


Hide 37100 2.INSTALL PROPELLER SHAFT WITH CENTER BEARING ASSEMBLY (for 4WD)

a.

Completely remove any oil, etc. and clean the contact surfaces of the propeller shaft flange and transfer flange.


b.

Completely remove any oil, etc. and clean the contact surfaces of the propeller shaft flange and differential flange.


c.

Align the matchmarks on the propeller shaft flange and transfer flange.


d.

Install the propeller shaft with center bearing assembly with the 4 nuts and 4 washers.

Torque:
88.2 N*m (899 kgf*cm, 65 ft.*lbf)


e.

Temporarily install the center support bearing bracket with the 2 bolts. Tighten the bolts as much as possible by hand.


f.

Align the matchmarks on the propeller shaft flange and differential flange.


g.

Install the propeller shaft with center bearing assembly with the 4 nuts and 4 washers.

Torque:
88.2 N*m (899 kgf*cm, 65 ft.*lbf)


h.
C317901C01
1.802,0.323 2.135,0.323 true 2.188,0.281 2.521,0.281 true 1.563,0.229 1.823,0.438 0.26,0.208 10 true *a 2.583,0.219 2.896,0.417 0.313,0.198 10 true *b
*a Center Bearing Housing Center Line
*b Center Bearing Center Line


Unload the vehicle and then make sure all 4 wheels are touching the ground and the vehicle is supporting all of its own weight. The center lines of the center bearing and center bearing housing (refer to the illustration) must be adjusted so that they are within 0 +/-1 mm (0 +/-0.0394 in.) of each other. Measure the difference along the front/rear axis of the vehicle.

Distance (A):

0 +/-1 mm (0 +/-0.0394 in.)



i.

Tighten the 2 bolts of the center support bearing bracket.

Torque:
36.2 N*m (369 kgf*cm, 27 ft.*lbf)


Hide 51569 3.INSTALL PROPELLER SHAFT GUARD

a.

for Pre-Runner:

i.
C317874

for Transmission side:

Attach the guide to install the propeller shaft guard with the 2 bolts.

Torque:
36.2 N*m (369 kgf*cm, 27 ft.*lbf)


ii.
C317875

for Center support bearing side:

Install the propeller shaft guard with the 2 bolts.

Torque:
36.2 N*m (369 kgf*cm, 27 ft.*lbf)



b.

for 4WD:

i.
C317868

for Transfer side:

Attach the guide to install the propeller shaft guard with the 2 bolts.

Torque:
36.2 N*m (369 kgf*cm, 27 ft.*lbf)


ii.
C317870C01
0.417,1.417 0.833,1.417 true 0.104,1.333 0.417,1.531 0.313,0.198 10 true *a 0.656,1.896 0.969,2.094 0.313,0.198 10 true A
*a End Bracket


for Center support bearing side:

Install the propeller shaft guard with the 2 bolts.

Torque:
36.2 N*m (369 kgf*cm, 27 ft.*lbf)

NOTICE:

Do not tighten bolt A with the rotation stopper of the end bracket rotated left.