Home › Engine / Hybrid System › 2TR-FE ENGINE CONTROL › SFI SYSTEM
NM1880E _51 Engine / Hybrid System _015470 2TR-FE ENGINE CONTROL _0076894 SFI SYSTEM DE DETAILS F

2TR-FE ENGINE CONTROL  SFI SYSTEM  DETAILS  KNOCK CONTROL SENSOR  


CONSTRUCTION


a.

In a conventional type knock control sensor (resonant type), a vibration plate is built into the sensor. This plate has the same resonance point as the knocking* frequency of the engine block. This sensor can only detect vibration in this frequency band.

*: The term "knock" or "knocking" is used in this case to describe either preignition or detonation of the air fuel mixture in the combustion chamber. This preignition or detonation refers to the air fuel mixture being ignited earlier than is advantageous. This use of "knock" or "knocking" is not primarily used to refer to a loud mechanical noise that may be produced by an engine.



b.

A flat type knock control sensor (non-resonant type) has the ability to detect vibration in a wider frequency band (from approximately 6 kHz to 15 kHz). It has the following features:

i.

The engine knocking frequency will vary slightly depending on the engine speed. The flat type knock control sensor can detect vibration even when the engine knocking frequency changes. Due to the use of the flat type knock control sensor, the vibration detection ability has been increased compared to a conventional type knock control sensor, and more precise ignition timing control is possible.

W100047
3.854,1.281 3.729,1.281 3.729,1.281 3.583,1.521 true 5.5,2.208 5.24,2.208 5.24,2.208 5.125,2.094 true 4,1.656 3.917,1.656 3.917,1.656 3.875,1.979 true 4,0.792 6.385,1.188 2.385,0.396 10 false Detection Band of Conventional Type 4.052,1.552 5.865,1.823 1.813,0.271 10 false Detection Band of Flat Type 3.115,2.354 3.896,2.625 0.781,0.271 10 false Frequency 1.177,1.302 1.75,1.604 0.573,0.302 10 false Voltage 1.583,0.375 1.823,0.563 0.24,0.188 10 false (V) 5.094,2.354 5.417,2.646 0.323,0.292 10 false (Hz) 3.885,1.188 4.073,1.375 0.188,0.188 10 false *1 5.531,2.115 5.719,2.302 0.188,0.188 10 false *2 0.219,2.833 4.344,3.146 4.125,0.313 10 false *1: Resonance characteristic of conventional type (resonant type) 0.229,3.198 4.052,3.531 3.823,0.333 10 false *2: Resonance characteristic of flat type (non-resonant type) 0.083,0.052 2.833,0.354 2.75,0.302 10 false - Characteristics of Knock Control Sensor -



c.

A flat type knock control sensor is installed in an engine by placing it over the stud bolt installed on the cylinder block. For this reason, a hole for the stud bolt exists in the center of the sensor.


d.

In the sensor, a steel weight is located in the upper portion. An insulator is located between the weight and the piezoelectric element.


e.

An open/short circuit detection resistor is integrated in the sensor. When the ignition switch is ON, the open/short circuit detection resistor in the knock control sensor and the resistor in the ECM keep the voltage at terminal KNK1 constant. An Integrated Circuit (IC) in the ECM constantly monitors the voltage of terminal KNK1. If the open/short circuit occurs between the knock control sensor and the ECM, the voltage of terminal KNK1 will change and the ECM will detect the open/short circuit and store a Diagnostic Trouble Code (DTC).

W100048
1.469,0.813 1.271,0.813 1.271,0.813 0.969,1.51 true 1.021,1.625 1.438,2.25 1.438,2.25 1.604,2.25 true 0.948,1.729 1.427,2.74 1.427,2.74 1.646,2.74 true 2.302,3.948 2.042,3.948 2.042,3.948 1.177,5.354 true 1.906,5.292 2.5,4.448 2.5,4.448 2.771,4.448 true 2.135,1.698 2.542,2.146 2.542,2.146 2.75,2.146 true 6.021,0.688 5.833,0.688 5.833,0.688 5.313,1.281 true 6.083,1.833 5.844,1.833 5.844,1.833 5.406,1.333 true 0.875,3.135 3.438,3.49 2.563,0.354 10 false Flat Type (Non-resonant Type) 4.365,3.156 7.146,3.5 2.781,0.344 10 false Conventional Type (Resonant Type) 6.115,1.76 7.156,2.104 1.042,0.344 10 false Vibration Plate 6.135,0.583 6.958,1.198 0.823,0.615 10 false Piezoelectric Element 1.688,2.635 3.094,2.969 1.406,0.333 10 false Piezoelectric Element 2.375,3.833 3.875,4.125 1.5,0.292 10 false Piezoelectric Element 2.844,2.052 4.24,2.573 1.396,0.521 10 false Open Circuit Detection Resistor 2.802,4.313 3.948,4.844 1.146,0.531 10 false Open Circuit Detection Resistor 1.51,0.729 2.438,1.021 0.927,0.292 10 false Steel Weight 1.646,2.156 2.281,2.406 0.635,0.25 10 false Insulator 4.25,4.073 4.656,4.229 0.406,0.156 10 false ECM 4.354,4.354 4.656,4.542 0.302,0.188 10 false 5 V 1.958,5.313 2.563,5.542 0.604,0.229 10 false 200 kΩ 4.573,4.76 5.177,4.99 0.604,0.229 10 false 220 kΩ 0.667,6 2.771,6.302 2.104,0.302 10 false Flat Type Knock Control Sensor 6.042,5.104 6.24,5.292 0.198,0.188 10 false IC 3.719,5.073 4.146,5.365 0.427,0.292 10 false KNK1 3.719,5.698 4.146,6 0.427,0.302 10 false EKNK


f.

Vibrations caused by knocking are transmitted to the steel weight. The inertia of this weight applies pressure to the piezoelectric element. This action generates electromotive force.

W102908
2.604,0.229 2.917,0.229 2.917,0.229 3.833,0.781 true 2.948,1.344 3.375,1.344 3.375,1.344 3.823,1.146 true 2.406,0.135 2.729,0.385 0.323,0.25 10 false *1 2.75,1.25 3.073,1.5 0.323,0.25 10 false *2
*1 Steel Weight *2 Piezoelectric Element
V100135

Inertia - -



g.

This sensor is mounted in the specific directions and angles illustrated. To prevent water accumulation in the connector, make sure to install the flat type knock control sensor in the position shown in the following illustration:

W102301
3.021,1.229 2.438,0.563 2.438,0.563 2.167,0.563 true 2.01,0.458 2.24,0.646 0.229,0.188 10 false *1 4.115,1.135 4.438,1.313 0.323,0.177 10 false 10° 4.115,1.323 4.438,1.5 0.323,0.177 10 false 10°
*1 Knock Control Sensor - -