Home › Engine / Hybrid System › 2TR-FE ENGINE CONTROL › SFI SYSTEM
NM1880E _51 Engine / Hybrid System _015470 2TR-FE ENGINE CONTROL _0076894 SFI SYSTEM CO CONTROL F

2TR-FE ENGINE CONTROL  SFI SYSTEM  CONTROL  ENGINE CONTROL  


FUNCTION OF MAIN COMPONENTS


a.

The main components of the engine control system are as follows:

Component Outline Quantity Function
ECM 32-bit CPU 1 The ECM optimally controls the SFI, ESA and ISC to suit the operating conditions of the engine in accordance with the signals provided by the sensors.
Intake Mass Air Flow Meter Sub-assembly Hot-wire Type 1 This sensor has a built-in hot-wire to directly detect the intake air mass.
Intake Air Temperature Sensor Thermistor Type 1 This sensor detects the intake air temperature by means of an internal thermistor.
Engine Coolant Temperature Sensor Thermistor Type 1 This sensor detects the engine coolant temperature by means of an internal thermistor.
Crankshaft Position Sensor [Rotor Teeth] Pick-up Coil Type (36-2) 1 This sensor detects the engine speed and performs cylinder identification.
Camshaft Position Sensor [Rotor Teeth] Pick-up Coil Type (3) 1 This sensor performs the cylinder identification.
Accelerator Pedal Position Sensor Linear (Non-contact) Type 1 This sensor detects the amount of pedal effort applied to the accelerator pedal.
Throttle Position Sensor Linear (Non-contact) Type 1 This sensor detects the throttle valve opening angle.
Knock Control Sensor Built-in Piezoelectric Type (Non-resonant Type/Flat Type) 1 This sensor detects an occurrence of engine knocking indirectly from the vibration of the cylinder block caused by the occurrence of engine knocking.
Oxygen Sensor Heated Type (Cup Type) 1 This sensor detects the oxygen concentration in the exhaust emissions by measuring the electromotive force which is generated in the sensor itself.
Fuel Injector Assembly 12-hole Type 4 The fuel injector assembly is an electromagnetically-operated nozzle which injects fuel in accordance with signals from the ECM.



SYSTEM CONTROL


a.

The engine control system has the following features. The ECM controls these systems:

System Outline
Sequential Multiport Fuel Injection (SFI)
·

An L-type SFI system directly detects the intake air mass with a hot wire type intake mass air flow meter sub-assembly.

·

The fuel injection system is a sequential multiport fuel injection system.

·

Fuel injection takes two forms:

·

Synchronous injection, which always takes place with the same timing in accordance with the basic injection duration and an additional correction based on the signals provided by the sensors.

·

Non-synchronous injection, which takes place at the time an injection request based on the signals provided by the sensors is detected, regardless of the crankshaft position.



·

Synchronous injection is further divided into group injection during a cold start, and independent injection after the engine is started.


Electronic Spark Advance (ESA)
·

Ignition timing is determined by the ECM based on signals from various sensors. The ECM corrects ignition timing in response to engine knocking.

·

This system selects the optimal ignition timing in accordance with the signals received from the sensors and sends the (IGT) ignition signal to the igniter.


Electronic Throttle Control System-intelligent (ETCS-i) Optimally controls the throttle valve opening in accordance with the amount of accelerator pedal effort and the condition of the engine and the vehicle.
Variable Valve Timing-intelligent (VVT-i) Controls the intake camshaft to an optimal valve timing in accordance with the engine condition.
Fuel Pump Control
·

Fuel pump operation is controlled by signals from the ECM.

·

The fuel pump is stopped when the Supplemental Restraint System (SRS) airbags are deployed.


Air Conditioning Cut-off Control By turning the air conditioning compressor assembly on or off in accordance with the engine condition, driveability is maintained.
Oxygen Sensor Heater Control Maintains the temperature of the oxygen sensor at an appropriate level to increase accuracy of detection of the oxygen concentration in the exhaust gas.
Engine Immobiliser Prohibits fuel delivery and ignition if an attempt is made to start the engine with an invalid key.
Diagnosis When the ECM detects a malfunction, the ECM diagnoses and memorizes the failed section.
Fail-safe When the ECM detects a malfunction, the ECM stops or controls the engine in accordance with the data already stored in memory.