Home › Engine / Hybrid System › 2TR-FE ENGINE MECHANICAL › DRIVE BELT › from 2012.09
RM1880E _51 Engine / Hybrid System _013210 2TR-FE ENGINE MECHANICAL _0068465 DRIVE BELT A

2TR-FE ENGINE MECHANICAL  DRIVE BELT  INSTALLATION  


PROCEDURE

Hide 1.INSTALL TENSIONER PULLEY

NOTICE:

Perform the following procedure when it is necessary to replace the tensioner pulley.


HINT:

The tensioner pulley service kit consists of a bolt, dust seal and tensioner pulley.


a.
A302380
2.406,0.25 2.313,0.135 2.313,0.135 2.146,0.135 false 1.698,1.469 1.927,1.469 false 0.552,1.031 0.552,1.438 false 0.458,1.49 0.771,1.646 0.313,0.156 10 false *1 1.948,0.031 2.26,0.188 0.313,0.156 10 false *2 1.979,1.365 2.292,1.521 0.313,0.156 10 false *3
*1 Bolt
*2 Tensioner Pulley
*3 Dust Seal
V100135

Front


Install the dust seal and bolt to the tensioner pulley as shown in the illustration.

NOTICE:
·

The dust seal must be oriented correctly when installed. If the dust seal is installed incorrectly, the bearing may be damaged.

·

Do not touch the seal surface of the bearing.



HINT:

Be sure to use the bolt from the service kit.



b.

Tighten the bolt by hand until the flange of the bolt contacts the dust seal and the tensioner pulley is fixed in place.

NOTICE:

Do not use any tools.



c.

Tighten the bolt.

Torque:
50 N*m (510 kgf*cm, 37 ft.*lbf)


d.

Install a new O-ring and the engine oil level dipstick guide with the bolt.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


e.

Install the engine oil level dipstick.


Hide 2.INSTALL FAN AND GENERATOR V BELT

a.
A252774
0.771,2.521 0.906,2.521 0.906,2.521 1.042,2.875 true 1.917,2.427 1.823,2.427 1.823,2.427 1.646,2.917 true 2.375,2.802 2.521,2.438 2.521,2.438 2.615,2.438 true 2.115,3.26 2.49,3.26 true 2.542,3.667 2.781,3.667 true 2.125,3.667 2.375,4.156 2.375,4.156 2.458,4.156 true 1.729,3.906 1.729,4.271 true 1.354,3.521 0.969,3.885 0.969,3.885 0.896,3.885 true 2.646,2.333 2.823,2.5 0.177,0.167 10 false *3 0.729,3.781 0.906,3.948 0.177,0.167 10 false *5 2.542,3.167 2.719,3.333 0.177,0.167 10 false *4 1.938,2.333 2.115,2.5 0.177,0.167 10 false *2 0.583,2.427 0.76,2.594 0.177,0.167 10 false *1 1.646,4.292 1.823,4.458 0.177,0.167 10 false *6 2.813,3.573 2.99,3.74 0.177,0.167 10 false *8 2.479,4.052 2.656,4.219 0.177,0.167 10 false *7
*1 Generator
*2 Idler Pulley
*3 Vane Pump
*4 Fan Pulley
*5 Tensioner Pulley
*6 Crankshaft Pulley
*7 No. 1 Idler Pulley
*8 Cooler Compressor


Install the fan and generator V belt to all the pulleys except the V-ribbed belt tensioner pulley.


b.

Use the hexagon-shaped part indicated by the arrow in the illustration to move the tensioner pulley downward, and then install the fan and generator V belt to the tensioner pulley.

NOTICE:
·

The backside of the fan and generator V belt should face the tensioner pulley.

·

Check that the fan and generator V belt is properly installed to each pulley.