Home › Engine / Hybrid System › 2TR-FE ENGINE MECHANICAL › CYLINDER HEAD
RM1880E _51 Engine / Hybrid System _013210 2TR-FE ENGINE MECHANICAL _0068472 CYLINDER HEAD A

2TR-FE ENGINE MECHANICAL  CYLINDER HEAD  REPLACEMENT  


PROCEDURE

Hide 1.REPLACE INTAKE VALVE GUIDE BUSH

a.

Heat the cylinder head to 80 to 100°C (176 to 212°F).


b.

Place the cylinder head on wooden blocks.


c.
A101402
1.146,0.906 0.469,0.333 0.469,0.333 1.063,1.302 true 0.125,0.198 0.563,0.406 0.438,0.208 10 false SST

Using SST and a hammer, tap out the guide bush.

SST
09201-01055  
09950-70010  (09951-07100)


d.

Using a caliper gauge, measure the bush bore diameter of the cylinder head.

Standard Bush Bore Diameter:
Item Specified Condition
STD 10.285 to 10.306 mm (0.405 to 0.406 in.)
O/S 0.05 10.335 to 10.356 mm (0.407 to 0.408 in.)


If the bush bore diameter of the cylinder head is more than 10.306 mm (0.406 in.), machine the bush bore so that the diameter is between 10.335 and 10.356 mm (0.407 and 0.408 in.).

If the bush bore diameter of the cylinder head is more than 10.356 mm (0.408 in.), replace the cylinder head.


e.

Select a new valve guide bush.

New Valve Guide Bush:
Item Specified Condition
Bush Bore Diameter 10.333 to 10.344 mm (0.4068 to 0.4072 in.) 10.383 to 10.394 mm (0.4088 to 0.4092 in.)
Bush to be Used STD O/S 0.05


HINT:

Standard bush length: 43.0 to 44.0 mm (1.69 to 1.73 in.)



f.

Heat the cylinder head to 80 to 100°C (176 to 212°F).


g.

Place the cylinder head on wooden blocks.


h.
A101405
1.063,1.229 0.427,0.229 0.427,0.229 1.135,0.813 true 2.948,1.271 3.125,1.469 0.177,0.198 10 false *1 0.104,0.125 0.448,0.323 0.344,0.198 10 false SST
*1 Protrusion Height


Using SST and a hammer, tap in a new valve guide bush to the specified protrusion height.

SST
09201-01055  
09950-70010  (09951-07100)

Standard protrusion height:

9.8 to 10.2 mm (0.386 to 0.402 in.)



i.
A101406

Using a sharp 5.5 mm reamer, ream the valve guide bush to obtain the standard clearance between the guide bush and valve stem.

Standard oil clearance:

0.025 to 0.060 mm (0.000984 to 0.00236 in.)



Hide 2.REPLACE EXHAUST VALVE GUIDE BUSH

a.

Heat the cylinder head to 80 to 100°C (176 to 212°F).


b.

Place the cylinder head on wooden blocks.


c.
G037435
1.844,0.719 2.198,0.198 2.198,0.198 1.979,1.115 true 2.229,0.083 2.677,0.323 0.448,0.24 10 false SST

Using SST and a hammer, tap out the guide bush.

SST
09201-01055  
09950-70010  (09951-07100)


d.

Using a caliper gauge, measure the bush bore diameter of the cylinder head.

Standard Bush Bore Diameter:
Item Specified Condition
STD 10.285 to 10.306 mm (0.405 to 0.406 in.)
O/S 0.05 10.335 to 10.356 mm (0.407 to 0.408 in.)


If the bush bore diameter of the cylinder head is more than 10.306 mm (0.406 in.), machine the bush bore so that the diameter is between 10.335 and 10.356 mm (0.407 and 0.408 in.).

If the bush bore diameter of the cylinder head is more than 10.356 mm (0.408 in.), replace the cylinder head.


e.

Select a new valve guide bush.

New Valve Guide Bush:
Item Specified Condition
Bush Bore Diameter 10.333 to 10.344 mm (0.4068 to 0.4072 in.) 10.383 to 10.394 mm (0.4088 to 0.4092 in.)
Bush to be Used STD O/S 0.05


HINT:

Standard bush length: 43.0 to 44.0 mm (1.69 to 1.73 in.)



f.

Heat the cylinder head to 80 to 100°C (176 to 212°F).


g.

Place the cylinder head on wooden blocks.


h.
A101408
1.792,0.646 1.99,0.104 1.99,0.104 1.896,1.042 true 0.948,1.354 1.219,1.563 0.271,0.208 10 false *1 2.01,0 2.375,0.198 0.365,0.198 10 false SST
*1 Protrusion Height


Using SST and a hammer, tap in a new valve guide bush to the specified protrusion height.

SST
09201-01055  
09950-70010  (09951-07100)

Standard protrusion height:

7.6 to 8.0 mm (0.299 to 0.315 in.)



i.
A101409

Using a sharp 5.5 mm reamer, ream the valve guide bush to obtain the standard clearance between the guide bush and valve stem.

Standard oil clearance:

0.030 to 0.065 mm (0.00118 to 0.00256 in.)



Hide 3.REPLACE CAMSHAFT BEARING CAP SETTING RING PIN

NOTICE:
A302858
0.958,2.677 1.271,2.833 0.313,0.156 10 false *1 0.396,2.229 0.708,2.385 0.313,0.156 10 false *2 2.802,2.344 3.115,2.5 0.313,0.156 10 false *3
*1 Height
*2 Width
*3 Protrusion Height


It is not necessary to remove a ring pin unless it is being replaced.


a.

Remove the ring pins.


b.

Using a plastic-faced hammer, tap in a new ring pin until the pin stops.

Standard Ring Pin:
Item Height Width Protrusion Height
Ring pin 7 mm (0.276 in.) 10 mm (0.394 in.) 2.5 to 3.8 mm (0.0984 to 0.150 in.)