Home › Engine / Hybrid System › 2TR-FE COOLING › RADIATOR
RM1880E _51 Engine / Hybrid System _013214 2TR-FE COOLING _0068494 RADIATOR A

2TR-FE COOLING  RADIATOR  DISASSEMBLY  


PROCEDURE

Hide 1.REMOVE RADIATOR BRACKET SUB-ASSEMBLY

a.
A120273

Remove the 4 bolts and 2 brackets.


Hide 2.REMOVE RADIATOR DRAIN COCK PLUG

a.

Remove the drain cock plug.


b.

Remove the O-ring.


Hide 3.ASSEMBLE SST

a.
A113337
2.823,1.104 2.396,1.74 2.396,1.74 2.302,1.74 true 2.375,0.708 2.677,0.281 2.677,0.281 2.771,0.281 false 2.25,2.781 2.448,3.042 2.448,3.042 2.542,3.042 false 0.458,2.49 0.656,2.75 0.656,2.75 0.75,2.75 false 2.823,0.208 3.083,0.49 0.26,0.281 10 false *1 2.115,1.656 2.396,1.938 0.281,0.281 10 false *2 0.375,1.323 0.698,1.573 0.323,0.25 10 false *3 2.594,2.948 3.063,3.229 0.469,0.281 10 false SST 0.813,2.667 1.323,2.969 0.51,0.302 10 false SST
*1 Part A
*2 Stopper Bolt
*3 Dimension B


Install the claw to part A of the overhaul handle as shown in the illustration.

SST
09230-01010  (09231-01010, 09231-01030)


b.

While squeezing the handle, adjust the stopper bolt so that dimension B is as specified below.

Dimension B:

0.2 to 0.3 mm (0.00787 to 0.0118 in.)


NOTICE:

If this adjustment is not performed, the claw will be damaged.



Hide 4.UNCAULK LOCK PLATE

a.
A113338
0.594,1.01 0.885,1.51 0.885,1.51 0.969,1.51 true 1.271,0.771 1.51,0.479 1.51,0.479 1.656,0.479 false 0.771,0.708 1.042,0.208 1.042,0.208 1.156,0.208 false 1.208,0.125 1.51,0.396 0.302,0.271 10 false *1 1.708,0.396 2.167,0.667 0.458,0.271 10 false SST 1.021,1.427 1.333,1.677 0.313,0.25 10 false *2
*1 Tank
*2 Lock Plate


Using SST, squeeze the handle until stopped by the stopper bolt to release the caulking.

SST
09230-01010  (09231-01010, 09231-01030)


Hide 5.REMOVE UPPER RADIATOR TANK AND LOWER RADIATOR TANK

a.
A099699

Lightly tap the bracket of the radiator (or the connection area for the radiator hose inlet or outlet) with a plastic-faced hammer and remove the tank.

NOTICE:

Do not tap automatic transmission oil cooler pipe.



b.

Remove the O-ring.


Hide 6.REMOVE OIL COOLER ASSEMBLY (for Automatic Transmission)

a.
A099700

Remove the 2 cooler pipes.


b.

Remove the 2 nuts, 2 plate washers and oil cooler.


c.

Remove the 2 O-rings from the oil cooler.