Home › Engine / Hybrid System › 2TR-FE STARTING › STARTER › 2011.07–2013.08
RM1880E _51 Engine / Hybrid System _013216 2TR-FE STARTING _0068502 STARTER G

2TR-FE STARTING  STARTER  INSPECTION  


PROCEDURE

Hide 1.INSPECT STARTER ASSEMBLY

CAUTION:

As a large electric current passes through the cable during this inspection, a thick cable must be used. If not, the cable may become hot and cause injury.


NOTICE:

These tests must be performed within 3 to 5 seconds to prevent the coil from burning out.


a.

Mount the starter in a vise between aluminum plates.


b.

Perform a pull-in test.

i.

Remove the nut and disconnect the lead wire from terminal C.


ii.
G039099
2.271,0.896 2.271,1.792 2.271,1.792 2,1.792 true 2.292,0.604 2.438,0.26 2.438,0.26 2.583,0.26 true 1.802,1.708 1.979,1.885 0.177,0.177 10 false *1 2.615,0.167 2.792,0.344 0.177,0.177 10 false *2
*1 Terminal C
*2 Terminal 50
V100135

Operation


Connect the battery to the starter as shown in the illustration. Check that the clutch pinion gear extends.

If the clutch pinion gear does not move, replace the repair service starter kit.



c.
G039100
1.875,1.031 1.875,1.948 1.875,1.948 2.073,1.948 true 2.281,0.281 2.156,0.281 2.156,0.281 1.969,0.781 true 2.313,0.208 2.469,0.375 0.156,0.167 10 false *2 2.094,1.865 2.25,2.031 0.156,0.167 10 false *1
*1 Terminal C
*2 Terminal 50
V100135

Disconnect


Perform a holding test.

i.

Disconnect the negative (-) terminal lead from terminal C with the condition specified in the pull-in test above being maintained. Check that the pinion gear remains out.

If the clutch pinion gear moves inward, replace the repair service starter kit.



d.
A251383
2.552,0.375 2.438,0.375 2.438,0.375 2.26,0.677 true 2.573,0.292 2.75,0.479 0.177,0.188 10 false *1
*1 Terminal 50
V100135

Disconnect
V100136

Operation


Inspect clutch pinion gear return.

i.

Disconnect the negative (-) terminal lead from the starter body. Check that the clutch pinion gear returns inward.

If the clutch pinion gear does not return inward, replace repair service starter kit.



e.
G039102
2.531,0.125 2.656,0.125 2.656,0.125 2.74,0.344 true 2.802,1.156 2.646,1.156 2.646,1.156 2.51,0.656 true 2.385,0.042 2.542,0.229 0.156,0.188 10 false *2 2.823,1.073 3.01,1.26 0.188,0.188 10 false *1
*1 Terminal 50
*2 Terminal 30


Perform an operation test without load.

i.

Connect the lead wire to terminal C.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


ii.

Connect the battery and an ammeter to the starter as shown in the illustration.


iii.

Check that the starter rotates smoothly and steadily while the pinion gear is moving out. Then measure the current.

Standard current:

90 A or less at 11.5 V


If the result is not as specified, replace the starter assembly.



Hide 2.INSPECT STARTER ARMATURE ASSEMBLY

a.

Check the commutator for dirt and/or burns on the surface.

If the surface is dirty or burnt, correct it with sandpaper (No. 400) or a lathe.

If necessary, replace the starter armature assembly.


b.

Inspect the commutator for an open circuit.

i.
A073983
1.448,1.104 1.729,0.417 1.729,0.417 1.865,0.417 true 1.938,0.333 2.25,0.531 0.313,0.198 10 false *1
*1 Segment


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Segment - Segment Always Below 1 Ω


If the result is not as specified, replace the starter armature assembly.



c.

Inspect the commutator for a short circuit.

i.
A073984
1.198,1.344 0.792,1.344 true 2.104,1.031 2.552,0.479 2.552,0.479 2.656,0.479 true 2.74,0.406 3.083,0.646 0.344,0.24 10 false *1 0.583,1.26 0.927,1.49 0.344,0.229 10 false *2
*1 Coil Core
*2 Segment


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Segment - Coil core Always 10 kΩ or higher


If the result is not as specified, replace the starter armature assembly.



d.
A058584
2.75,0.938 2.927,1.135 0.177,0.198 10 *1
*1 Length


Using a vernier caliper, measure the protrusion length.

Standard length:

3.1 mm (0.122 in.)


Maximum length:

3.8 mm (0.150 in.)


If the length is more than the maximum, replace the starter armature assembly.


Hide 3.INSPECT STARTER COMMUTATOR END FRAME ASSEMBLY

a.
A076677
2.854,0.833 3.031,1.031 0.177,0.198 10 *1
*1 Length


Check the brush length.

i.

Using a vernier caliper, measure the brush length.

Standard exposed length:

9.0 mm (0.354 in.)


Minimum exposed length:

4.0 mm (0.157 in.)


If the length is less than the minimum, replace the starter commutator end frame assembly.



b.
A076436

Check the resistance.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Positive (+) brush - Negative (-) brush Always 10 kΩ or higher


If the result is not as specified, repair or replace the starter commutator end frame assembly.



Hide 4.INSPECT STARTER CENTER BEARING CLUTCH SUB-ASSEMBLY

a.

Check the gear teeth on the planetary gears, and the internal gear and pinion gear of the starter center bearing clutch for wear or damage.

If any of the gears is damaged, replace the center bearing clutch sub-assembly.


b.
A251384
1.365,0.667 1.354,0.667 false 3.25,2 3.417,2.167 0.167,0.167 10 false -
V100135

Free
V100136

Lock


Check the starter center bearing clutch pinion gear.

i.

Hold the starter center bearing clutch, rotate the pinion gear clockwise and check that pinion gear turns freely. Try to rotate the pinion gear counterclockwise and check that it locks.

If the result is not as specified, replace the center bearing clutch sub-assembly.



Hide 5.INSPECT REPAIR SERVICE STARTER KIT

a.
A058586

Check the plunger.

i.

Push in the plunger and check that it returns quickly to its original position.

If the result is not as specified, replace the repair service starter kit.



b.
G037611
1.99,0.281 1.854,0.281 1.854,0.281 1.469,0.885 true 0.823,1.938 0.958,1.938 0.958,1.938 1.24,1.563 true 2.052,0.208 2.323,0.438 0.271,0.229 10 false *1 0.625,1.865 0.917,2.073 0.292,0.208 10 false *2
*1 Terminal C
*2 Terminal 50


Check the resistance.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Terminal 50 - Terminal C Always Below 1 Ω


If the result is not as specified, replace the repair service starter kit.


ii.
G037612
1.073,1.958 1.219,1.958 1.219,1.958 1.417,1.594 true 1.417,0.417 1.604,0.135 1.604,0.135 1.708,0.135 true 0.885,1.854 1.052,2.021 0.167,0.167 10 false *1 1.74,0.052 1.906,0.219 0.167,0.167 10 false *2
*1 Terminal 50
*2 Repair Service Starter Kit Body


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Terminal 50 - repair service starter kit body Always Below 2 Ω


If the result is not as specified, replace the repair service starter kit.