Home › Drivetrain › R150 MANUAL TRANSMISSION / TRANSAXLE › OUTPUT SHAFT › 2011.07–2012.09
RM1880E _52 Drivetrain _013219 R150 MANUAL TRANSMISSION / TRANSAXLE _0068531 OUTPUT SHAFT A

R150 MANUAL TRANSMISSION / TRANSAXLE  OUTPUT SHAFT  DISASSEMBLY  


PROCEDURE

Hide 7.REMOVE 1ST GEAR

D026050
2.198,0.656 2.042,1.115 false 2.094,0.479 2.458,0.677 0.365,0.198 10 false SST

a.

Using SST and a press, press out the 5th gear, output shaft center bearing, 1st gear thrust washer and 1st gear from the output shaft.

SST
09950-00020  


Hide 8.REMOVE NO. 1 SYNCHRONIZER RING (FOR 1ST GEAR)

a.

Remove synchronizer ring (for 1st gear) from the output shaft.


Hide 9.REMOVE 1ST GEAR THRUST WASHER PIN

a.

Remove the thrust washer pin from the output shaft.


Hide 10.REMOVE 1ST GEAR NEEDLE ROLLER BEARING

a.

Remove the needle roller bearing from the output shaft.


Hide 11.REMOVE 1ST GEAR BEARING SPACER

a.

Remove the bearing spacer from the output shaft.


Hide 12.REMOVE BEARING SHAFT SNAP RING

a.
D026055

Using 2 screwdrivers and a hammer, tap the snap ring from the output shaft.

NOTICE:

Use a cloth to prevent the snap ring from flying off.



Hide 13.REMOVE 2ND GEAR

a.
D026056
2.188,0.906 2.375,0.438 false 2.24,0.219 2.594,0.417 0.354,0.198 10 false SST

Using SST and a press, press out the No. 1 transmission clutch hub together with the reverse gear, No. 1 synchronizer ring set (for 2nd gear) and 2nd gear from the output shaft.

SST
09950-00020  


Hide 14.REMOVE 2ND GEAR NEEDLE ROLLER BEARING

a.

Remove the needle roller bearing from the output shaft.


Hide 15.REMOVE REVERSE GEAR

a.
D026058

Remove the reverse gear, 3 No. 1 synchromesh shifting keys and 3 synchromesh shifting key springs.

NOTICE:

Use a cloth to prevent the shifting key and the shifting key springs from popping out.



Hide 16.REMOVE CLUTCH HUB SET SHAFT SNAP RING

a.

Using a snap ring expander, remove the snap ring from the output shaft.

NOTICE:

Do not damage the sliding surface of the bearing.



Hide 17.REMOVE 3RD GEAR

a.
D026060
2.49,0.479 2.208,0.865 false 2.365,0.281 2.677,0.479 0.313,0.198 10 false SST

Using SST and a press, press out the No. 2 transmission clutch hub together with the No. 2 transmission hub sleeve, No. 2 synchronizer ring and 3rd gear from the output shaft.

SST
09950-00020  


Hide 18.REMOVE 3RD GEAR NEEDLE ROLLER BEARING

a.

Remove the needle roller bearing from the output shaft.


Hide 19.REMOVE NO. 2 TRANSMISSION HUB SLEEVE

a.

Remove the No. 2 hub sleeve, 3 No. 2 synchromesh shifting key springs and 3 No. 2 synchromesh shifting keys from the No. 2 clutch hub.


Hide 25.INSPECT NO. 1 SYNCHRONIZER RING SET (FOR 1ST GEAR)

Hide 26.INSPECT NO. 1 SYNCHRONIZER RING SET (FOR 2ND GEAR)

Hide 27.INSPECT NO. 2 SYNCHRONIZER RING (FOR 3RD GEAR)