Home › Drivetrain › DRIVE SHAFT / PROPELLER SHAFT › PROPELLER SHAFT ASSEMBLY
RM1880E _52 Drivetrain _013220 DRIVE SHAFT / PROPELLER SHAFT _0068534 PROPELLER SHAFT ASSEMBLY A

DRIVE SHAFT / PROPELLER SHAFT  PROPELLER SHAFT ASSEMBLY  DISASSEMBLY  


PROCEDURE

Hide 1.REMOVE CENTER NO. 1 SUPPORT BEARING ASSEMBLY

a.
C282106
0.427,0.427 1.656,0.427 1.656,0.427 1.656,0.771 true 1.521,0.427 1.521,0.708 true 0.229,0.354 0.594,0.615 0.365,0.26 10 false *1
*1 Matchmark


Place matchmarks on the flange coupling and flange yoke.


b.

Remove the 4 nuts and 4 washers.


c.

Disconnect the propeller shaft and intermediate shaft.


d.
A098690

Fix the flange coupling in a vise between aluminum plates at the center bearing section.

NOTICE:

Do not overtighten the vise.



e.

Using a chisel and hammer, loosen the staked part of the lock nut.

NOTICE:

Loosen the staked part of the lock nut completely. Otherwise, the screw of the intermediate shaft may be damaged.



f.
F049875
2.333,1.104 2.552,1.583 2.552,1.583 2.635,1.583 false 2.667,1.469 3.135,1.708 0.469,0.24 10 false SST

Using SST and a socket wrench, remove the lock nut and washer.

SST
09330-00021  


g.
F049874
1.833,1.094 3.073,1.094 true 1.823,1.406 2.875,1.406 2.875,1.406 2.875,1.094 true 3.135,1 3.375,1.333 0.24,0.333 10 false *1
*1 Matchmark


Place matchmarks on the intermediate shaft and flange coupling.


h.
F049876
2.854,0.479 3.26,0.75 0.406,0.271 10 false SST

Using SST, remove the flange coupling from the intermediate shaft.

SST
09950-30012  (09951-03010, 09953-03010, 09954-03010, 09955-03030, 09956-03030)


i.

Remove the center support bearing.


Hide 2.REMOVE UNIVERSAL JOINT SPIDER ASSEMBLY

HINT:

Use the same procedure for all universal joint spiders.


a.
F015023
1.823,0.979 1.823,0.26 1.823,0.26 2.438,0.26 true 1.958,1 1.958,0.26 true 2.5,0.177 2.813,0.438 0.313,0.26 10 false *1
*1 Matchmark


Place matchmarks on the yoke and shaft.


b.
C061264

Using a brass bar and hammer, slightly tap in the spider bearing outer races.


c.

Using 2 screwdrivers, remove the 4 snap rings from the grooves.


d.
F015025
1.26,0.625 1.135,0.115 1.135,0.115 1.031,0.115 true 2.063,1.396 2.5,1.188 true 0.708,0.052 1.177,0.354 0.469,0.302 10 false SST 1.948,1.323 2.302,1.635 0.354,0.313 10 false A

Clamp the shaft in a vise between aluminum plates.

NOTICE:

Do not overtighten the vise.



e.

Using SST, push the yoke side spider bearing until: 1) the spider almost touches the yoke or shaft, and 2) the spider bearing on the opposite side is partially pushed out.

SST
09332-25010  

HINT:

Before installing SST, sufficiently raise the part labeled A. If part A is too low, SST may be difficult to install.



f.
C237736
2.167,0.688 2.677,0.688 true 2.042,1.156 2.552,1.156 false 2.76,0.604 3.188,0.948 0.427,0.344 10 false *a 2.677,1.073 3.073,1.396 0.396,0.323 10 false *1
*1 Plastic-faced Hammer
*a Hammering Point


Clamp the pushed out spider bearing outer race in a vise between aluminum plates and tap the shaft to remove the spider bearing.

NOTICE:
·

Do not tap the shaft tube.

·

Do not overtighten the vise.



HINT:

Use the same procedure to remove the spider bearing from the opposite side of the spider.



g.

Remove the yoke and spider from the shaft.


h.
F015030
1.01,0.771 0.75,0.146 0.75,0.146 0.677,0.146 true 2.104,1.26 2.552,1.073 true 0.354,0.073 1,0.49 0.646,0.417 10 false SST 1.958,1.208 2.281,1.573 0.323,0.365 10 false A

Reinstall the 2 removed spider bearings to the spider and clamp the spider bearings in a vise between aluminum plates.

NOTICE:

Do not overtighten the vise.



i.

Using SST, push the yoke side spider bearing until: 1) the spider almost touches the yoke, and 2) the spider bearing on the opposite side is partially pushed out.

SST
09332-25010  

HINT:

Before installing SST, sufficiently raise the part labeled A. If part A is too low, SST may be difficult to install.



j.
C237737
2.531,0.531 3.01,0.531 true 2.573,1.021 3.052,1.021 false 3.083,0.448 3.323,0.76 0.24,0.313 10 false *a 3.125,0.948 3.417,1.208 0.292,0.26 10 false *1
*1 Plastic-faced Hammer
*a Hammering Point


Clamp the pushed out spider bearing outer race in a vise between aluminum plates and tap the yoke to remove the spider bearing.

NOTICE:

Do not overtighten the vise.


HINT:

Use the same procedure to remove the spider bearing from the opposite side of the spider.



k.

Remove the spider from the yoke.