Home › Brake › BRAKE SYSTEM (OTHER) › BRAKE FLUID
RM1880E _54 Brake _013227 BRAKE SYSTEM (OTHER) _0068564 BRAKE FLUID N

BRAKE SYSTEM (OTHER)  BRAKE FLUID  BLEEDING  


CAUTION / NOTICE / HINT

HINT:

If any work is performed on the brake system or if air in the brake lines is suspected, bleed air from the brake system.


NOTICE:
·

Apply the parking brake before bleeding the brakes.

·

Add brake fluid to keep the level between the MIN and MAX lines of the reservoir while bleeding the brakes.

·

If brake fluid leaks onto any painted surface, immediately wash it off.

·

When bleeding air, select the suitable procedure listed below.

Replaced/Installed Item Work Procedure
Flexible hose (front/rear) Bleed brake line
Front disc brake cylinder assembly
Rear wheel cylinder assembly
Load sensing proportioning valve Bleed brake system
Brake actuator assembly (w/ ABS)
Brake master cylinder sub-assembly
Brake master cylinder reservoir assembly
Brake booster assembly



PROCEDURE

Hide 1.BLEED BRAKE LINE

a.

Remove the brake master cylinder reservoir filler cap assembly.


b.

Add brake fluid to keep the level between the MIN and MAX lines of the reservoir while bleeding the brakes.

Fluid:

SAE J1703 or FMVSS No. 116 DOT 3



c.

Remove the bleeder plug cap.


d.

Connect a vinyl tube to the bleeder plug.


e.

Depress the brake pedal several times, and then loosen the bleeder plug with the pedal depressed.*1


f.

When fluid stops coming out, tighten the bleeder plug, and then release the brake pedal.*2


g.

Repeat *1 and *2 until all the air in the fluid is completely bled out.


h.

Tighten the bleeder plug completely.

Torque:
for Front Brake : 10 N*m (102 kgf*cm, 7 ft.*lbf)
for Rear Brake : 11 N*m (112 kgf*cm, 8 ft.*lbf)


i.

Install the bleeder plug cap.


j.

Repeat the above procedure for each wheel to bleed the brake line.


k.

Check for brake fluid leaks.


l.

Check the brake fluid level in the reservoir (See page Brake>BRAKE SYSTEM (OTHER)>BRAKE FLUID>ON-VEHICLE INSPECTION).


Hide 2.BLEED BRAKE SYSTEM

a.

Bleed the brake master cylinder.

i.

Remove the brake master cylinder reservoir filler cap assembly.


ii.

Add brake fluid to keep the level between the MIN and MAX lines of the reservoir while bleeding the brakes.

Fluid:

SAE J1703 or FMVSS No. 116 DOT 3



iii.

Using a union nut wrench, disconnect the 2 brake tubes from the master cylinder.


iv.

Slowly depress and hold the brake pedal.

C238133
3.542,0.115 3.833,0.365 0.292,0.25 10 false *B 0.146,0.094 0.49,0.302 0.344,0.208 10 false *A
*A for LHD *B for RHD



v.

Block the tube holes with your fingers, and then release the brake pedal.

C239738
0.164,0.097 0.383,0.274 0.219,0.177 10 *A 3.569,0.097 3.788,0.274 0.219,0.177 10 *B
*A for LHD *B for RHD



vi.

Remove the your fingers, slowly depress and hold the brake pedal, block the tube holes with your fingers again, and then release the brake pedal. Repeat this step 3 or 4 times.


vii.

Using a union nut wrench, connect the 2 brake tubes to the brake master cylinder assembly.

Torque:
15 N*m (155 kgf*cm, 11 ft.*lbf)

NOTICE:

Use the formula to calculate special torque values for situations where a union nut wrench is combined with a torque wrench (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).




b.

Bleed the load sensing proportioning valve.

i.

Remove the bleeder plug cap.


ii.

Connect a vinyl tube to the bleeder plug.


iii.

Depress the pedal several times, and then loosen the bleeder plug with the pedal depressed.


iv.

When fluid stops coming out, immediately tighten the bleeder plug. Then release the pedal.


v.

Repeat the 2 previous steps until all the air in the brake fluid is gone.


vi.

Tighten the bleeder plug.

Torque:
11 N*m (107 kgf*cm, 8 ft.*lbf)


vii.

Install the bleeder plug cap.



c.

Bleed the brake line.

i.

Remove the bleeder plug cap.


ii.

Connect a vinyl tube to the bleeder plug.


iii.

Depress the brake pedal several times, and then loosen the bleeder plug with the pedal depressed.*1


iv.

When fluid stops coming out, tighten the bleeder plug, and then release the brake pedal.*2


v.

Repeat *1 and *2 until all the air in the fluid is completely bled out.


vi.

Tighten the bleeder plug completely.

Torque:
for Front Brake : 10 N*m (102 kgf*cm, 7 ft.*lbf)
for Rear Brake : 11 N*m (112 kgf*cm, 8 ft.*lbf)


vii.

Repeat the above procedure for each wheel to bleed the brake line.


viii.

Install the bleeder plug cap.



d.

Check for brake fluid leaks.


e.

Check the brake fluid level in the reservoir (See page Brake>BRAKE SYSTEM (OTHER)>BRAKE FLUID>ON-VEHICLE INSPECTION).