Home › Brake › BRAKE SYSTEM (OTHER) › LOAD SENSING PROPORTIONING VALVE
RM1880E _54 Brake _013227 BRAKE SYSTEM (OTHER) _0068568 LOAD SENSING PROPORTIONING VALVE G

BRAKE SYSTEM (OTHER)  LOAD SENSING PROPORTIONING VALVE  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 1.CHECK LOAD SENSING PROPORTIONING VALVE ASSEMBLY

F102360
2.344,0.844 2.719,1.167 0.375,0.323 10 false *a
*a Weight


a.

Set the vehicle to its curb weight.


b.

Place weights (as necessary) on the rear deck until the rear axle load is as shown below.

Standard rear axle load:

8532 N (870 kgf, 1918 lbf)


NOTICE:
·

Be sure that the vehicle is on a level surface before starting the procedure.

·

When placing the weights on the vehicle, first place approximately 60 kg (132 lb) above the specification. Then remove weights as necessary to adjust the load.




c.
F049820
1.021,0.396 1.219,0.396 false 2.583,0.396 2.375,0.396 false 0.667,0.313 1.052,0.573 0.385,0.26 10 false SST 2.625,0.313 3.052,0.594 0.427,0.281 10 false SST

Install SST, and bleed air from the brake system.

SST
09709-29018  


d.
F049822
0.521,0.365 0.677,0.365 false 2.604,0.365 2.365,0.365 false 0.167,0.281 0.75,0.646 0.583,0.365 10 false SST 2.646,0.281 3.052,0.594 0.406,0.313 10 false SST

Raise the front brake fluid pressure to 10000 kPa (102 kgf/cm2, 1450 psi) by depressing the brake pedal and check the rear brake fluid pressure.

Standard rear brake fluid pressure:

3580 +/-740 kPa (36.5 +/-7.5 kgf/cm2, 519 +/-107 psi)


HINT:
·

The pedal should not be depressed twice or released while the specified pressure is being set.

·

Read the value of the rear brake fluid pressure after adjusting and holding the specified brake fluid pressure for 2 seconds.

If necessary, adjust the load sensing proportioning valve.




Hide 2.ADJUST LOAD SENSING PROPORTIONING VALVE ASSEMBLY

a.
F043205
2.219,0.719 1.74,1.24 1.74,1.24 1.74,1.396 false 2.438,0.719 2.885,1.302 2.885,1.302 2.885,1.396 true 2.406,1.51 2.677,1.813 0.271,0.302 10 false A 2.969,0.833 3.177,1.083 0.208,0.25 10 false B 1.667,1.417 1.948,1.656 0.281,0.24 10 false *1 2.813,1.417 3.052,1.656 0.24,0.24 10 false *2
*1 Adjusting Nut
*2 Lock Nut


Loosen the lock nut.


b.

Adjust the rear brake fluid pressure by changing the length of "A" or "B".

i.

For lower pressure - Lengthen "A" or "B"


ii.

For higher pressure - Shorten "A" or "B"

HINT:

The rear brake fluid pressure changes according to the table below by adjusting the length of "A" or "B".


Pressure (Reference):
Condition Specified Condition
For one turn of lock nut "A" 220 kPa (2.2 kgf/cm2, 32 psi)
For 1 mm (0.0394 in.) of "B" length 30 kPa (0.3 kgf/cm2, 4.4 psi)




c.

Tighten the lock nut.

Torque:
13 N*m (130 kgf*cm, 9 ft.*lbf)