Home › Steering › POWER ASSIST SYSTEMS › VANE PUMP
RM1880E _55 Steering _013231 POWER ASSIST SYSTEMS _0068578 VANE PUMP A

POWER ASSIST SYSTEMS  VANE PUMP  REASSEMBLY  


CAUTION / NOTICE / HINT

NOTICE:
·

When using a vise, place aluminum plates between the part and vise.

·

When using a vise, do not overtighten it.



PROCEDURE

Hide 1.INSTALL VANE PUMP HOUSING OIL SEAL

a.
G036583
2.479,0.75 2.594,0.583 2.594,0.583 2.76,0.583 false 2.594,0.927 2.594,0.583 false 2.813,0.479 3.281,0.74 0.469,0.26 10 false SST

Using SST and a press, press in a new oil seal.

SST
09950-60010  
09950-70010  (09951-00280, 09951-07100)

NOTICE:
·

Make sure to install the oil seal so that it faces the correct direction.

·

Be careful not to damage the oil seal.




Hide 2.INSTALL SHAFT WITH PULLEY

a.

Coat the shaft with power steering fluid.


b.
F051464
1.677,1.094 1.219,0.271 1.219,0.271 0.927,0.271 false 0.708,0.146 1.01,0.406 0.302,0.26 10 false *1
*1 Protective Tape


Tape the serrated part of the shaft.

NOTICE:

Be careful not to damage the oil seal.



c.

Install the shaft with pulley to the front housing.


Hide 3.INSTALL FRONT VANE PUMP SIDE PLATE

a.
C065369

Coat a new No. 2 O-ring with power steering fluid.


b.

Install the No. 2 O-ring to the front housing.


c.
C065368

Coat a new No. 1 O-ring with power steering fluid.


d.

Install the No. 1 O-ring to the front side plate.


e.
F050370

Install the front side plate to the front housing while aligning the semicircle-shaped cuts of both parts.

NOTICE:

Be sure to install the plate in the correct position and with the correct orientation.



Hide 4.INSTALL VANE PUMP CAM RING

a.
F050371
0.427,0.438 0.583,0.438 0.583,0.438 0.896,0.667 true 0.219,0.365 0.51,0.688 0.292,0.323 10 false *1
*1 Inscribed Mark


With the inscribed mark facing upward, install the vane pump cam ring to the front housing while aligning the semicircle-shaped cuts of both parts.

NOTICE:

Be sure to install the plate in the correct position and with the correct orientation.



Hide 5.INSTALL VANE PUMP ROTOR

a.
C095038

Install the vane pump rotor to the front housing.

HINT:

The top and bottom of the vane pump rotor are symmetrical.



b.
F050372
0.635,1.063 1.115,1.344 0.479,0.281 10 false *a 2.448,0.156 2.906,0.573 0.458,0.417 10 false *b
*a Outward
*b Inward


Coat the 10 vane pump plates with power steering fluid.


c.

Install the 10 vane pump plates.

NOTICE:

Make sure that the round ends of the vane pump plates are facing outward.



Hide 6.INSTALL VANE PUMP SHAFT SNAP RING

a.
F051011

Using a screwdriver and snap ring expander, install a new snap ring to the shaft with pulley.


Hide 7.INSTALL REAR HOUSING

a.
F050373

Coat a new O-ring with power steering fluid and install it to the rear housing.


b.

Align the straight pin of the rear housing with the hole created by the semicircle-shaped cuts of the cam ring, front side plate and front housing. Then install the rear housing with the 4 bolts.

Torque:
22 N*m (224 kgf*cm, 16 ft.*lbf)

NOTICE:

Make sure that the O-ring is not out of position before installing the rear housing.



Hide 8.INSPECT ROTATING TORQUE

a.
C053369

Check that the pump rotates smoothly without abnormal noise.


b.

Temporarily install the service bolt.

Recommended Service Bolt:
Item Specified Condition
Thread Diameter 10 mm (0.394 in.)
Thread Pitch 1.25 mm (0.0492 in.)
Bolt Length 50 mm (1.97 in.)



c.

Using a torque wrench, check the pump rotating torque.

Standard rotating torque:

0.27 N*m (3 kgf*cm, 2 in.*lbf) or less


If the rotating torque is not as specified, check the installation of the housing oil seal.


Hide 9.INSTALL POWER STEERING OIL PRESSURE SWITCH

a.

Coat a new O-ring with power steering fluid and install it to the oil pressure switch.


b.

Install the oil pressure switch to the vane pump.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


Hide 10.INSTALL FLOW CONTROL VALVE

a.
F042475

Coat the compression spring and flow control valve with power steering fluid.


b.

Install the compression spring.


c.

Install the flow control valve so that it faces the correct direction.


d.

Coat a new O-ring with power steering fluid and install it to the pressure port union.


e.

Install the pressure port union.

Torque:
69 N*m (704 kgf*cm, 51 ft.*lbf)


Hide 11.INSTALL VANE PUMP OIL RESERVOIR SUB-ASSEMBLY

a.

Coat a new O-ring with power steering fluid, and install it to the vane pump oil reservoir.


b.

Install the vane pump oil reservoir to the vane pump with the 3 bolts.

Torque:
9.0 N*m (92 kgf*cm, 80 in.*lbf)


Hide 12.INSTALL VANE PUMP OIL RESERVOIR CAP SUB-ASSEMBLY