Home › Steering › STEERING COLUMN › STEERING PAD SWITCH
RM1880E _55 Steering _013232 STEERING COLUMN _0068581 STEERING PAD SWITCH G

STEERING COLUMN  STEERING PAD SWITCH  INSPECTION  


PROCEDURE

Hide 1.INSPECT STEERING PAD SWITCH ASSEMBLY

a.

Measure the resistance according to the value(s) in the table below.

C288365
3.854,1.188 4.198,0.75 4.198,0.75 4.417,0.75 true 3.813,1.406 4.208,1.625 4.208,1.625 4.427,1.625 true 3.698,1.406 3.969,2.135 3.969,2.135 4.188,2.135 true 3.594,1.406 3.813,2.448 3.813,2.448 4.031,2.448 true 3.479,1.406 3.281,2.385 3.281,2.385 3.021,2.385 true 3.344,1.208 3.104,0.656 3.104,0.656 2.844,0.656 true 5.698,2.396 6.094,2.615 6.094,2.615 6.313,2.615 true 1.479,2.646 1.104,3.198 1.104,3.198 0.844,3.198 true 1.49,2.365 0.948,2.729 0.948,2.729 0.688,2.729 true 1.073,2 0.667,2.313 0.667,2.313 0.406,2.313 true 1,1.604 0.51,1.073 0.51,1.073 0.25,1.073 true 1.198,1.333 0.813,0.677 0.813,0.677 0.552,0.677 true 1.688,1.583 2.021,1.063 2.021,1.063 2.24,1.063 true 3.01,1.646 2.938,1.385 2.938,1.385 2.76,1.385 true 1.563,1.333 1.75,0.406 1.75,0.406 1.969,0.406 true 2.021,0.333 2.333,0.49 0.313,0.156 10 false *1 0.385,0.615 0.698,0.771 0.313,0.156 10 false *2 2.292,0.99 2.604,1.146 0.313,0.156 10 false *3 0.083,1.01 0.396,1.167 0.313,0.156 10 false *4 0.24,2.24 0.552,2.396 0.313,0.156 10 false *5 0.521,2.656 0.833,2.813 0.313,0.156 10 false *6 0.677,3.135 0.99,3.292 0.313,0.156 10 false *7 6.365,2.542 6.677,2.698 0.313,0.156 10 false *8 2.594,1.323 2.813,1.521 0.219,0.198 10 false *9 2.615,0.594 2.927,0.792 0.313,0.198 10 false HO 4.469,0.656 5.083,0.854 0.615,0.198 10 false IL+2 4.49,1.542 4.948,1.74 0.458,0.198 10 false AU1 4.25,2.052 4.708,2.25 0.458,0.198 10 false AU2 4.094,2.365 4.552,2.563 0.458,0.198 10 false EAU 2.677,2.313 3.292,2.51 0.615,0.198 10 false DISP
*1 Volume+ Switch *2 Volume- Switch
*3 Seek+ Switch *4 Seek- Switch
*5 MODE Switch *6 On Hook Switch
*7 Off Hook Switch *8 DISP Switch
*9 Horn Wire - -


Standard Resistance:
Tester Connection Switch Condition Specified Condition
9 (AU2) - 8 (EAU) No switch pushed 95 to 105 kΩ
9 (AU2) - 8 (EAU) MODE switch pushed Below 2.5 Ω
9 (AU2) - 8 (EAU) On hook switch pushed 312.6 to 345.5 Ω
9 (AU2) - 8 (EAU) Off hook switch pushed 950 to 1050 Ω
10 (AU1) - 8 (EAU) No switch pushed 95 to 105 kΩ
10 (AU1) - 8 (EAU) Seek+ switch pushed Below 2.5 Ω
10 (AU1) - 8 (EAU) Seek- switch pushed 312.6 to 345.5 Ω
10 (AU1) - 8 (EAU) Volume+ switch pushed 950 to 1050 Ω
10 (AU1) - 8 (EAU) Volume- switch pushed 2954.5 to 3265.5 Ω
7 (DISP) - 8 (EAU) DISP switch pushed Below 2.5 Ω
1 (HO) - Horn wire Always Below 2.5 Ω


If the result is not as specified, replace the steering pad switch assembly.


b.

Connect the battery positive (+) lead to terminal IL+2 and the negative (-) lead to terminal EAU of the steering pad switch assembly connector.


c.

Check that the switch illumination comes on.

OK:

Steering pad switch illumination comes on.


If the result is not as specified, replace the steering pad switch assembly.