Home › Steering › STEERING COLUMN › STEERING SYSTEM
RM1880E _55 Steering _013232 STEERING COLUMN _0068582 STEERING SYSTEM N

STEERING COLUMN  STEERING SYSTEM  ADJUSTMENT  


PROCEDURE

Hide 1.ADJUST STEERING CENTER

HINT:

This is the adjustment procedure for when the steering is off center.


a.

Check if the steering wheel is off center.

i.
C238857
1.719,0.698 2.083,0.26 true 1.813,0.906 2.083,0.26 2.083,0.26 2.302,0.26 true 1.146,0.469 1.031,0.26 1.031,0.26 0.917,0.26 true 2.031,0.979 2.219,1.146 2.219,1.146 2.323,1.146 true 0.719,0.198 1.063,0.49 0.344,0.292 10 false *2 2.344,0.188 2.635,0.427 0.292,0.24 10 false *1 2.344,1.063 2.646,1.313 0.302,0.25 10 false *3
*1 Masking Tape
*2 Steering Wheel
*3 Steering Column Upper Cover


Apply masking tape to the top center of the steering wheel and steering column upper cover.


ii.

Drive the vehicle in a straight line for 100 m (328 ft.) at a constant speed of 56 km/h (35 mph), and hold the steering wheel to maintain the course.


iii.
C238858
1.375,0.615 1.104,0.396 true 1.354,1.052 1.104,0.396 1.104,0.396 0.885,0.396 true 1.604,0.635 1.792,0.458 true 1.594,0.969 1.792,0.458 1.792,0.458 2.198,0.458 true 1.927,1.031 2.25,1.333 0.323,0.302 10 false *2 0.688,0.333 0.927,0.573 0.24,0.24 10 false *1 1.875,0.167 2.198,0.49 0.323,0.323 10 false *3 2.25,0.406 2.521,0.667 0.271,0.26 10 false *4
*1 Masking Tape
*2 Steering Wheel
*3 Steering Column Upper Cover
*4 Marked Line


Draw a line on the masking tape as shown in the illustration.


iv.

Turn the steering wheel to the center position.

HINT:

Look at the upper surface of the steering wheel, steering spoke and SRS airbag line to find the center position.



v.
C238859
1.458,0.531 1.198,0.323 true 1.448,0.969 1.198,0.323 1.198,0.323 0.979,0.323 true 1.677,0.552 1.875,0.375 true 1.677,0.948 1.875,0.375 1.875,0.375 2.281,0.375 true 1.958,0.938 2.25,1.208 0.292,0.271 10 false *2 0.771,0.24 1.083,0.542 0.313,0.302 10 false *1 1.979,0.156 2.281,0.448 0.302,0.292 10 false *3 2.333,0.302 2.677,0.604 0.344,0.302 10 false *4
*1 Masking Tape
*2 Steering Wheel
*3 Steering Column Upper Cover
*4 Marked Line


Draw a new line on the masking tape on the steering wheel as shown in the illustration.


vi.

Measure the distance between the 2 lines on the masking tape on the steering wheel.


vii.

Convert the measured distance to steering angle.

HINT:
·

Measured distance of 1 mm (0.0394 in.) = Steering angle of approximately 1 degree.

·

Make a note of the steering angle.





b.

Adjust the steering angle.

i.
R000429
2.021,1.51 3.406,2.104 1.385,0.594 10 false *1
*1 Matchmark


Draw a line on the RH and LH tie rod ends and rack ends where it can be easily seen.


ii.

Measure the distance from the RH and LH tie rod ends to the ends of the rack end screws.

HINT:
·

Measure both the RH and LH sides.

·

Make a note of the measured values.




iii.
F051053

Remove the RH and LH boot clips from the rack boots.


iv.

Loosen the RH and LH lock nuts.


v.

Turn the RH and LH rack ends by the same amount (but in different directions) according to the steering angle.

HINT:

One 360 degree turn of the rack ends (1.5 mm (0.0591 in.) horizontal movement) equals 12 degrees of steering angle.



vi.

Tighten the RH and LH lock nuts to the specified torque.

Torque:
56 N*m (566 kgf*cm, 41 ft.*lbf)

NOTICE:

Make sure that the difference between the distances from the RH and LH tie rod ends to the ends of the rack end screws is within 1.0 mm (0.0394 in.).



vii.

Install the RH and LH boot clips.