Home › Steering › STEERING GEAR / LINKAGE › STEERING GEAR
RM1880E _55 Steering _013233 STEERING GEAR / LINKAGE _0068583 STEERING GEAR A

STEERING GEAR / LINKAGE  STEERING GEAR  REMOVAL  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.



PROCEDURE

Hide 1.REMOVE FRONT WHEELS

Hide 2.REMOVE FRONT SIDE MEMBER TO FRONT SUSPENSION CROSSMEMBER BRACE

a.

Remove the 8 bolts and 2 crossmember braces.


Hide 3.REMOVE NO. 1 ENGINE UNDER COVER (w/ Engine Under Cover)

a.

Remove the 2 bolts and No. 1 engine under cover.


Hide 4.REMOVE FRONT SIDE MEMBER TO FRONT SUSPENSION CROSSMEMBER BRACE

a.

Remove the 10 bolts and 2 crossmember braces.


Hide 5.REMOVE FRONT STABILIZER BAR

Hide 6.DISCONNECT TIE ROD END SUB-ASSEMBLY LH

a.

Remove the cotter pin and nut.


b.
C237621
1.771,1.333 1.927,1.896 1.927,1.896 2.052,1.896 false 2.125,1.792 3.083,2.073 0.958,0.281 10 false SST

Using SST, disconnect the tie rod end from the steering knuckle arm.

SST
09628-00011  


Hide 7.DISCONNECT TIE ROD END SUB-ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 8.DISCONNECT STEERING SLIDING YOKE

a.
C281607
1.448,1.177 1.604,1.677 1.604,1.677 2.042,1.677 true 1.542,1.073 1.76,1.677 true 2.083,1.552 2.396,1.708 0.313,0.156 10 true *1 1.427,0.198 1.74,0.354 0.313,0.156 10 true A 0.969,0.896 1.156,1.104 0.188,0.208 10 true B
*1 Matchmark


Loosen the bolt labeled A.


b.

Place matchmarks on the steering sliding yoke and steering intermediate shaft.


c.

Remove the bolt labeled B.


d.
C237951

Disconnect the steering sliding yoke from the steering intermediate shaft.


Hide 9.REMOVE NO. 2 STEERING INTERMEDIATE SHAFT SUB-ASSEMBLY

a.
C281608
0.969,1.052 0.969,0.281 0.969,0.281 0.417,0.281 true 0.823,1.156 0.823,0.281 true 0.188,0.156 3.281,2.01 3.094,1.854 10 false *1
*1 Matchmark


Place matchmarks on the intermediate shaft and steering link.


b.
C239646

Remove the bolt.


c.

Remove the intermediate shaft from the steering link.


Hide 10.DISCONNECT PRESSURE FEED TUBE ASSEMBLY

a.
C131078
2.146,1.26 2.458,1.74 2.458,1.74 2.708,1.74 true 1.604,0.417 2.021,0 false 2.76,1.635 2.917,1.813 0.156,0.177 10 false *1
*1 Union Nut Wrench


Using a union nut wrench, loosen the flare nut and disconnect the pressure feed tube.


b.
C241320

Remove the bolt and disconnect the pressure feed tube from the steering link.


Hide 11.DISCONNECT STEERING GEAR OUTLET RETURN TUBE

a.
C288378

Detach the clip and disconnect the return hose.


b.
C131076
2.208,1.135 2.552,1.677 2.552,1.677 2.708,1.677 true 2.75,1.563 3.094,1.75 0.344,0.188 10 false *1
*1 Union Nut Wrench


Using a union nut wrench, disconnect the outlet return tube.


Hide 12.REMOVE POWER STEERING LINK ASSEMBLY

a.
C241323

Fix the 2 nuts in place and remove the 2 bolts. Then remove the link from the frame.

NOTICE:

Never turn the nut. Be sure to turn the bolt.


HINT:

Removal of the link may be easier if the following is performed: 1) remove the differential mount, and 2) slide the differential toward the rear of the vehicle.