Home › Steering › STEERING GEAR / LINKAGE › STEERING GEAR
RM1880E _55 Steering _013233 STEERING GEAR / LINKAGE _0068583 STEERING GEAR A

STEERING GEAR / LINKAGE  STEERING GEAR  DISASSEMBLY  


CAUTION / NOTICE / HINT

NOTICE:
·

When using a vise, place aluminum plates between the part and vise.

·

When using a vise, do not overtighten it.



HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.



PROCEDURE

Hide 1.REMOVE STEERING TURN PRESSURE TUBE

a.

Using a union nut wrench, remove the 2 turn pressure tubes.


b.

Remove the 4 O-rings.


Hide 2.SECURE POWER STEERING LINK ASSEMBLY

a.
C239649
2.573,0.865 2.49,0.292 2.49,0.292 2.344,0.292 false 2,0.198 2.438,0.406 0.438,0.208 10 false SST

Using SST, secure the steering link between aluminum plates in a vise, as shown in the illustration.

SST
09612-00012  


Hide 3.REMOVE TIE ROD END SUB-ASSEMBLY LH

a.
G035023
1.865,1.198 1.865,1.76 true 2.073,1.188 1.865,1.76 1.865,1.76 1.688,1.76 true 1.49,1.646 3.219,1.958 1.729,0.313 10 false *1
*1 Matchmark


Place matchmarks on the tie rod end, lock nut and rack end.


b.

Loosen the lock nut and remove the tie rod end and lock nut.


Hide 4.REMOVE TIE ROD END SUB-ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 5.REMOVE STEERING RACK BOOT CLAMP LH

a.
G100528

Using pliers and a screwdriver, remove the clamp.

NOTICE:

Be careful not to damage the boot.



Hide 6.REMOVE STEERING RACK BOOT CLAMP RH

HINT:

Use the same procedure described for the LH side.


Hide 7.REMOVE STEERING RACK BOOT CLIP LH

a.

Using pliers, remove the clip.

NOTICE:

Be careful not to damage the boot.



Hide 8.REMOVE STEERING RACK BOOT CLIP RH

HINT:

Use the same procedure described for the LH side.


Hide 9.REMOVE STEERING RACK BOOT LH

Hide 10.REMOVE STEERING RACK BOOT RH

Hide 11.REMOVE STEERING RACK END SUB-ASSEMBLY

a.
ZX09339

Using a screwdriver and hammer, unstake the washers.

NOTICE:

Do not strike the steering rack.



b.
C239910
0.875,1.25 0.76,1.469 0.76,1.469 0.667,1.469 false 1.281,2.813 1.396,2.813 1.396,2.813 1.635,3.219 false 2.531,0.677 2.646,0.302 2.646,0.302 2.74,0.302 false 1.708,3.917 1.813,4.448 1.813,4.448 1.917,4.448 true 0.083,0.083 0.365,0.25 0.281,0.167 10 false *A 2.302,2.573 2.615,2.729 0.313,0.156 10 false *b 0.344,1.365 0.833,1.615 0.49,0.25 10 false SST 1.99,4.344 2.198,4.5 0.208,0.156 10 false *1 2.844,1.385 3.156,1.615 0.313,0.229 10 false *b 0.094,2.208 0.719,2.375 0.625,0.167 10 false *B 0.948,2.688 1.448,2.917 0.5,0.229 10 false SST 2.802,0.198 3.229,0.385 0.427,0.188 10 false SST 0.156,1.021 0.469,1.177 0.313,0.156 10 false *a
*A for RH Side
*B for LH Side
*1 Wrench
*a Hold
*b Turn


Using a wrench, hold the steering rack (LH side).


c.

Using SST, remove the steering rack end (LH side) from the power steering rack.

SST
09922-10010  

HINT:

Rotate SST in the direction shown in the illustration.



d.

Using SST, remove the steering rack end (RH side) from the power steering rack.

SST
09922-10010  

HINT:

Rotate SST in the direction shown in the illustration.



e.

Remove the 2 claw washers.


Hide 12.REMOVE RACK GUIDE

a.
F102170
1.521,0.792 1.427,0.25 1.427,0.25 1.25,0.25 false 0.917,0.146 1.375,0.344 0.458,0.198 10 false SST

Using SST, remove the lock nut.

SST
09922-10010  


b.
C281609
1.323,1.188 0.74,0.76 0.74,0.76 0.552,0.76 true 0.365,0.677 0.677,0.833 0.313,0.156 10 false *1
*1 24 mm Hexagon Wrench


Using a 24 mm hexagon wrench, remove the rack guide spring cap.


c.

Remove the spring and rack guide.


Hide 13.REMOVE POWER STEERING CONTROL VALVE

a.
G100343

Remove the 2 bolts.


b.

Pull out the control valve from the rack housing.


c.

Remove the control valve gasket.


d.
F043533
2,1.146 2.188,0.823 2.188,0.823 2.302,0.823 true 2.354,0.719 2.635,0.896 0.281,0.177 10 false *1
*1 Screw Extractor


Using a screw extractor, remove the 2 union seats from the control valve housing.


Hide 14.REMOVE CYLINDER END STOPPER

a.
F043535
1.813,0.24 2.26,0.125 2.26,0.125 2.417,0.125 false 2.521,0.021 3.021,0.229 0.5,0.208 10 false SST

Using SST, remove the stopper.

SST
09631-20120  


Hide 15.REMOVE POWER STEERING RACK AND OIL SEAL

a.
G038614
1.26,0.24 1.615,0.24 false 0.885,0.146 1.354,0.333 0.469,0.188 10 false SST

Using SST, press out the steering rack and oil seal.

SST
09950-70010  (09951-07200)

NOTICE:

Take care not to drop the steering rack.



b.

Remove the oil seal from the steering rack.


c.

Remove the bush from the steering rack.


Hide 16.INSPECT POWER STEERING RACK

a.
G038615

Insert a wire 20 mm (0.787 in.) into the vent hole of the steering rack and make sure that the vent hole is not clogged with grease.

NOTICE:

If the hole is clogged, the pressure inside the boot will change after the boot is assembled and the steering wheel is turned.



Hide 17.REMOVE "TEFLON" RING

a.

Using a screwdriver, remove the "Teflon" ring and O-ring from the steering rack.

NOTICE:

Be careful not to damage the groove of the ring.



Hide 18.REMOVE POWER STEERING CYLINDER TUBE OIL SEAL

a.
F048024
2.063,0.792 1.563,0.427 1.563,0.427 2.656,0.427 false 1.24,0.313 1.729,0.531 0.49,0.219 10 false SST

Install SST (09612-07120) to SST (09612-07210).

SST
09612-70100  (09612-07120, 09612-07210)

NOTICE:
·

Lightly apply MP grease to the tip of SST (09612-07230) and inside of SST (09612-07210 and 09612-07120) before use.

·

Completely install SST (09612-07120) to SST (09612-07210) to prevent damage to the inside of the rack housing.




b.
C238627
0.344,1.083 0.552,1.625 0.552,1.625 0.865,1.625 false 0.865,1 0.708,1.625 false 2.885,1.323 3.208,1.802 3.208,1.802 2.917,1.802 true 0.958,1.521 1.552,1.948 0.594,0.427 10 false SST 2.594,1.688 2.958,1.865 0.365,0.177 10 false SST

Insert SST (09612-07210) into the rack housing at an angle until it comes in contact with the power steering cylinder tube oil seal. Install SST (09612-07220) to SST (09612-07210).

SST
09612-70100  (09612-07120, 09612-07210, 09612-07220)

NOTICE:

Do not damage the inside of the power steering rack housing.



c.
C238628
0.594,1.031 0.802,1.573 0.802,1.573 1.115,1.573 false 1.115,0.948 0.958,1.573 false 2.885,1.313 3.125,1.833 3.125,1.833 2.896,1.833 true 1.198,1.469 1.698,1.719 0.5,0.25 10 false SST 2.594,1.708 3,1.917 0.406,0.208 10 false SST

Hold SST (09612-07220) and pull SST (09612-07210) to position SST (09612-07120) inside of the rack housing.

SST
09612-70100  (09612-07120, 09612-07210, 09612-07220, 09612-07230)

HINT:

Make sure that SST (09612-07120) is positioned at the chamfered part between the power steering cylinder tube oil seal and the rack housing.



d.
C238629
1.292,1.771 1.375,1.948 1.375,1.948 1.688,1.948 false 1.479,1.708 1.563,1.948 false 1.344,0.604 1.531,0.646 1.531,0.646 1.531,0.948 true 1.531,0.958 1.438,0.958 false 1.771,1.833 2.188,2.052 0.417,0.219 10 false SST 1.135,0.844 1.5,1.021 0.365,0.177 10 false SST

Install SST (09612-07240) to SST (09612-07230). Insert the tip of SST (09612-07230) into the service hole of SST (09612-07120) in the rack housing.

SST
09612-70100  (09612-07120, 09612-07230, 09612-07240)

NOTICE:
·

Make sure that SST (09612-07240) is installed to prevent damage to SST (09612-07120).

·

Do not damage the inside of the rack housing.




e.
C238630
1.573,0.365 1.802,0.156 1.802,0.156 1.927,0.156 false 2,0.073 2.354,0.25 0.354,0.177 10 false SST

Install SST (09951-07150) to SST (09612-07230). Using a press, remove the power steering cylinder tube oil seal.

SST
09612-70100  (09612-07120, 09612-07230, 09612-07240)
09950-70010  (09951-07150)

NOTICE:

Do not damage the rack housing.


HINT:

Replace SST (09951-07150) with another of different length from the set if necessary.