Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM(for Radio and Display Type)
RM1880E _56 Audio / Visual / Telematics _013234 AUDIO / VIDEO _0068594 AUDIO AND VISUAL SYSTEM(for Radio and Display Type) J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(for Radio and Display Type)  Radio Receiver Power Source Circuit  


DESCRIPTION

This circuit provides power to the radio and display receiver assembly.

WIRING DIAGRAM

C240233
5.344,2.958 6.583,3.542 1.24,0.583 10 false Radio and Display Receiver Assembly 5.552,0.781 5.75,1 0.198,0.219 10 false B 5.552,1.927 6.063,2.25 0.51,0.323 10 false IG 5.552,2.531 6.031,2.802 0.479,0.271 10 false GND 5.552,1.365 6.042,1.667 0.49,0.302 10 false ACC 5.198,2.313 5.396,2.51 0.198,0.198 10 false 7 5.052,2.521 5.615,2.76 0.563,0.24 10 false G129 5.198,1.74 5.385,1.927 0.188,0.188 10 false 1 5.052,1.948 5.698,2.229 0.646,0.281 10 false G127 5.052,0.781 5.531,1.021 0.479,0.24 10 false G129 5.198,0.573 5.49,0.875 0.292,0.302 10 false 4 5.198,1.156 5.365,1.354 0.167,0.198 10 false 3 2.813,1.219 3.333,1.49 0.521,0.271 10 false ACC 2.823,0.625 3.344,0.802 0.521,0.177 10 false RAD 0.781,0.771 1.719,1.115 0.938,0.344 10 false from Battery 0.781,1.354 1.594,1.771 0.813,0.417 10 false from Ignition Switch 5.052,1.365 5.49,1.563 0.438,0.198 10 false G129

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER - BATTERY AND BODY GROUND)
a.

Disconnect the G129 and G127 radio and display receiver assembly connectors.


C240234
0.49,0.885 0.917,1.167 0.427,0.281 0.281,2.396 0.708,2.677 0.427,0.281 1.99,0.833 2.281,0.615 2.281,0.615 2.448,0.615 true 2.156,0.948 2.438,1.25 2.438,1.25 2.552,1.25 true 1.688,1.156 1.365,1.531 1.365,1.531 1.26,1.531 true 1.042,2.542 1.594,3.094 1.594,3.094 1.708,3.094 true 0.135,0.094 0.448,0.25 0.313,0.156 10 false *a 0.531,0.948 1.063,1.229 0.531,0.281 10 false G129 0.333,2.458 0.781,2.688 0.448,0.229 10 false G127 0.927,1.448 1.375,1.677 0.448,0.229 10 false GND 2.604,1.167 3.052,1.396 0.448,0.229 10 false B 2.49,0.542 2.938,0.771 0.448,0.229 10 false ACC 1.76,3.01 2.208,3.24 0.448,0.229 10 false IG
*a Front view of wire harness connector
(to Radio and Display Receiver Assembly)


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G129-7 (GND) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G129-4 (B) - Body ground Always 11 to 14 V
G129-3 (ACC) - Body ground Ignition switch ACC
G127-1 (IG) - Body ground Ignition switch ON



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR