Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM(for Radio and Display Type)
RM1880E _56 Audio / Visual / Telematics _013234 AUDIO / VIDEO _0068594 AUDIO AND VISUAL SYSTEM(for Radio and Display Type) J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(for Radio and Display Type)  Sound Signal Circuit between Radio Receiver and Stereo Jack Adapter  


DESCRIPTION

The No. 1 stereo jack adapter assembly sends an external device sound signal to the radio and display receiver assembly through this circuit.

The sound signal that has been sent is amplified by the radio and display receiver assembly, and then is sent to the speakers.

If there is an open or short in the circuit, sound cannot be heard from the speakers even if there is no malfunction in the radio and display receiver assembly or speakers.

WIRING DIAGRAM

C240216
1.677,2.948 1.885,3.104 0.208,0.156 10 false 9 1.677,2.438 1.885,2.594 0.208,0.156 10 false 7 1.677,1.927 1.885,2.083 0.208,0.156 10 false 5 1.677,1.417 1.885,1.573 0.208,0.156 10 false 6 1.677,3.448 1.885,3.604 0.208,0.156 10 false 8 1.677,4.583 1.885,4.74 0.208,0.156 10 false 3 1.677,4.083 1.885,4.24 0.208,0.156 10 false 2 5.333,2.865 5.594,3.052 0.26,0.188 10 false 11 1.135,3.052 1.74,3.448 0.604,0.396 10 false AGND 1.135,2.552 1.844,2.844 0.708,0.292 10 false ASGN 1.229,2.042 1.719,2.313 0.49,0.271 10 false ARO 1.25,1.531 1.635,1.76 0.385,0.229 10 false ALO 1.135,3.542 1.906,3.969 0.771,0.427 10 false AUXO 5.698,3.063 6.26,3.313 0.563,0.25 10 false AGND 5.344,2.354 5.792,2.625 0.448,0.271 10 false 27 5.698,2.563 6.198,2.813 0.5,0.25 10 false VA- 5.344,1.844 5.833,2.167 0.49,0.323 10 false 26 5.698,2.042 6.208,2.344 0.51,0.302 10 false VAR+ 5.333,1.333 5.604,1.573 0.271,0.24 10 false 28 5.698,1.531 6.208,1.833 0.51,0.302 10 false VAL+ 5.24,1.531 5.75,1.802 0.51,0.271 10 false G127 5.333,3.375 5.698,3.656 0.365,0.281 10 false 25 5.698,3.552 6.26,3.823 0.563,0.271 10 false ADPG 5.385,4.51 5.594,4.667 0.208,0.156 10 false 3 5.375,4 5.583,4.156 0.208,0.156 10 false 2 0.625,5.708 1.813,6.219 1.188,0.51 10 false No. 1 Stereo Jack Adapter Assembly 0.625,5.531 1.073,5.823 0.448,0.292 10 false G3 5.5,5.615 6.729,6.146 1.229,0.531 10 false Radio and Display Receiver Assembly 5.25,4.198 5.75,4.448 0.5,0.25 10 false G123 5.25,4.698 5.729,4.917 0.479,0.219 10 false G123 4.021,3.229 4.854,3.583 0.833,0.354 10 false Shielded 2.573,3.229 3.417,3.51 0.844,0.281 10 false Shielded 5.24,2.042 5.75,2.313 0.51,0.271 10 false G127 5.24,2.552 5.75,2.823 0.51,0.271 10 false G127 5.24,3.063 5.75,3.333 0.51,0.271 10 false G127 5.24,3.573 5.75,3.844 0.51,0.271 10 false G127

PROCEDURE

1.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER - STEREO JACK ADAPTER)
a.

Disconnect the G127 and G123 radio and display receiver assembly connectors.


b.

Disconnect the G3 No. 1 stereo jack adapter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G127-28 (VAL+) - G3-6 (ALO) Always Below 1 Ω
G127-26 (VAR+) - G3-5 (ARO)
G127-27 (VA-) - G3-7 (ASGN)
G127-11 (AGND) - G3-9 (AGND)
G127-25 (ADPG) - G3-8 (AUXO)
G123-2 - G3-2
G123-3 - G3-3
G127-28 (VAL+) - Body ground Always 10 kΩ or higher
G127-26 (VAR+) - Body ground
G127-27 (VA-) - Body ground
G127-11 (AGND) - Body ground
G127-25 (ADPG) - Body ground
G123-2 - Body ground
G123-3 - Body ground



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR