Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › REAR VIEW MONITOR SYSTEM
RM1880E _56 Audio / Visual / Telematics _013235 PARK ASSIST / MONITORING _0068600 REAR VIEW MONITOR SYSTEM U

PARK ASSIST / MONITORING  REAR VIEW MONITOR SYSTEM  TERMINALS OF ECU  


CHECK RADIO AND DISPLAY RECEIVER ASSEMBLY


E224535
4.311,0.543 4.757,0.76 0.446,0.218 4.358,0.582 4.724,0.737 0.366,0.154 10 G127 3.161,0.543 3.463,0.76 0.302,0.218 3.211,0.582 3.429,0.737 0.218,0.154 10 G2 2.259,1.425 2.705,1.64 0.447,0.215 2.304,1.463 2.675,1.617 0.371,0.154 10 G128 1.452,1.425 1.866,1.64 0.414,0.215 1.485,1.463 1.847,1.617 0.362,0.154 10 G129

a.

Disconnect the G129 radio and display receiver assembly connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G129-3 (ACC) - G129-7 (GND) GR - BR Accessory (On) Ignition switch off Below 1 V
Ignition switch ACC 11 to 14 V
G129-4 (B) - G129-7 (GND) L-Y - BR Battery Always 11 to 14 V
G129-7 (GND) - Body ground BR - Body ground Ground Always Below 1 Ω

If the result is not as specified, there may be a malfunction on the wire harness side.


c.

Reconnect the G129 radio and display receiver assembly connector.


d.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G2-8 (V+) - G2-16 (V-) L - Y Display signal Ignition switch ON, shift lever in R Pulse generation
(See waveform 1)
Ignition switch ON, shift lever in R, screen blacked out by covering camera lens Pulse generation
(See waveform 2)
G2-7 (CA+) - G2-15 (CGND) B - Shielded Power source Ignition switch ON, shift lever in R 5.5 to 7.05 V
G2-15 (CGND) - Body ground Shielded - Body ground Shielding Always Below 1 V
G127-2 (REV) - G129-7 (GND) R-Y - BR Reverse signal Ignition switch ON, shift lever in R 7.5 to 14 V
Ignition switch ON, shift lever not in R Below 1 V

If the result is not as specified, the radio and display receiver assembly may have a malfunction.


e.
E159949
0.196,1.018 0.531,1.162 0.335,0.144 10 GND

Using an oscilloscope, check waveform 1.

Measurement Condition
Item Content
Terminal No. (Symbol) G2-8 (V+) - G2-16 (V-)
Tool Setting 0.2 V/DIV., 50 μs/DIV.
Condition Ignition switch ON, shift lever in R


f.
E164781
0.275,1.002 0.612,1.146 0.337,0.145 10 GND

Using an oscilloscope, check waveform 2.

Measurement Condition
Item Content
Terminal No. (Symbol) G2-8 (V+) - G2-16 (V-)
Tool Setting 0.2 V/DIV., 50 μs/DIV.
Condition Ignition switch ON, shift lever in R, screen blacked out by covering camera lens