Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › TOYOTA PARKING ASSIST-SENSOR SYSTEM
RM1880E _56 Audio / Visual / Telematics _013235 PARK ASSIST / MONITORING _0068601 TOYOTA PARKING ASSIST-SENSOR SYSTEM J

PARK ASSIST / MONITORING  TOYOTA PARKING ASSIST-SENSOR SYSTEM  Clearance Sonar Main Switch Circuit  


DESCRIPTION

When the back sonar or clearance sonar switch assembly is turned on, an ON signal is sent to the rear clearance warning ECU assembly, and the TOYOTA parking assist-sensor system starts operating.

WIRING DIAGRAM

E224546
5.365,2.885 6.875,3.51 1.51,0.625 10 false Rear Clearance Warning ECU Assembly 5.365,2.677 5.74,2.906 0.375,0.229 10 false T1 3.135,1.594 4.719,2.188 1.583,0.594 10 false Back Sonar or Clearance Sonar Switch Assembly 3.115,1.385 3.49,1.604 0.375,0.219 10 false G74 0.198,0.896 1.521,1.365 1.323,0.469 10 false from Ignition Switch 1.781,1.063 3,1.542 1.219,0.479 10 false ECU-IG&GAUGE 5.438,0.781 5.719,1.063 0.281,0.281 10 false 10 5.719,0.906 6.208,1.177 0.49,0.271 10 false IG 5.438,2.031 5.75,2.302 0.313,0.271 10 false 21 5.708,2.146 6.219,2.479 0.51,0.333 10 false E 3.104,0.771 3.458,0.958 0.354,0.188 10 false 3 4.552,0.771 5.01,0.927 0.458,0.156 10 false 4 4.167,1.021 4.594,1.302 0.427,0.281 10 false ECU 3.292,1.021 3.583,1.26 0.292,0.24 10 false IG

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.INSPECT BACK SONAR OR CLEARANCE SONAR SWITCH ASSEMBLY
a.

Remove the back sonar or clearance sonar switch assembly.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>CLEARANCE SONAR MAIN SWITCH>REMOVAL


b.
E224539
1.823,1.375 1.917,1.896 1.917,1.896 2.104,1.896 true 1.615,1.375 1.531,1.896 1.531,1.896 1.344,1.896 true 2.177,1.813 2.458,2.104 0.281,0.292 10 false IG 0.99,1.823 1.406,2.115 0.417,0.292 10 false ECU

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
3 (IG) - 4 (ECU) On Below 1 Ω
3 (IG) - 4 (ECU) Off 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (BACK SONAR OR CLEARANCE SONAR SWITCH ASSEMBLY - REAR CLEARANCE WARNING ECU ASSEMBLY)

NG

REPLACE BACK SONAR OR CLEARANCE SONAR SWITCH ASSEMBLY

2.CHECK HARNESS AND CONNECTOR (BACK SONAR OR CLEARANCE SONAR SWITCH ASSEMBLY - REAR CLEARANCE WARNING ECU ASSEMBLY)
a.

Disconnect the G74 back sonar or clearance sonar switch assembly connector.


b.

Disconnect the T1 rear clearance warning ECU assembly connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G74-3 (IG) - Body ground Ignition switch ON 11 to 14 V
G74-3 (IG) - Body ground Ignition switch off Below 1 V



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G74-4 (ECU) - T1-10 (IG) Always Below 1 Ω
G74-4 (ECU) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (REAR CLEARANCE WARNING ECU ASSEMBLY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (REAR CLEARANCE WARNING ECU ASSEMBLY - BODY GROUND)
a.

Disconnect the T1 rear clearance warning ECU assembly connector.


b.
B155759
1.51,0.667 1.927,0.917 0.417,0.25 2.125,1.469 2.302,1.771 2.302,1.771 2.448,1.771 true 0.083,0.063 0.469,0.427 0.385,0.365 10 false *a 1.635,0.708 1.969,0.938 0.333,0.229 10 false T1 2.51,1.698 2.844,2.031 0.333,0.333 10 false E
*a Front view of wire harness connector
(to Rear Clearance Warning ECU Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
T1-21 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR