Home › Power Source / Network › 2TR-FE BATTERY / CHARGING › GENERATOR
RM1880E _57 Power Source / Network _013236 2TR-FE BATTERY / CHARGING _0068603 GENERATOR A

2TR-FE BATTERY / CHARGING  GENERATOR  DISASSEMBLY  


PROCEDURE

Hide 1.REMOVE GENERATOR PULLEY

a.

Mount the generator in a vise between aluminum plates.


b.
A303247
2.844,0.385 2.479,0.125 2.479,0.125 2.219,0.125 true 2.688,1.542 2.896,1.542 2.896,1.542 3.188,0.573 true 1.656,0.042 2.385,0.417 0.729,0.375 10 false SST 1-B 2.063,1.458 2.781,1.76 0.719,0.302 10 false SST 1-A 1.531,1.917 1.781,2.104 0.25,0.188 10 false *a 0.854,1.896 1.073,2.104 0.219,0.208 10 false *b
*a Hold
*b Turn


Install SST 1-A and SST 1-B to the generator rotor shaft.

SST
09820-63011  (09820-06010, 09820-06021)

Item Part No.
SST 1-A and 1-B 09820-06010
SST 2 09820-06021


c.

Hold SST 1-A with a torque wrench and turn SST 1-B clockwise with the specified torque.

Torque:
39 N*m (398 kgf*cm, 29 ft.*lbf)

NOTICE:

Make sure that SST is secured to the generator rotor shaft.



d.
A203850
2.708,0.5 2.781,0.5 2.781,0.5 2.833,0.771 false 2.271,0.438 2.688,0.583 0.417,0.146 10 false SST 2
V100135

Insert


Insert SST 2 to attach it to the pulley nut.


e.
A251404
0.917,3.012 1.08,3.195 0.163,0.183 10 *a
*a Hold
V100135

Turn


To loosen the pulley nut, turn SST 1-A in the direction shown in the illustration.

NOTICE:

To prevent damage to the rotor shaft, do not loosen the pulley nut more than one-half turn.



f.

Remove SST 2 from the generator.


g.
A251411
3.156,0.594 3.156,1.281 3.156,1.281 3,1.281 true 2.125,0.24 2.979,0.24 2.979,0.24 2.979,0.396 true 2.448,1.198 3.01,1.354 0.563,0.156 10 false SST 1-A 1.531,0.156 2.094,0.323 0.563,0.167 10 false SST 1-B 0.885,1.719 1.073,1.896 0.188,0.177 10 false *a
*a Hold
V100135

Turn


Turn SST 1-A in the direction shown in the illustration and remove SST 1-A and 1-B.


h.

Remove the pulley nut and pulley.


Hide 2.REMOVE GENERATOR REAR END COVER

a.
A118436

Remove the 3 nuts and generator rear end cover.


Hide 3.REMOVE TERMINAL INSULATOR

A118437

Hide 4.REMOVE GENERATOR BRUSH HOLDER ASSEMBLY

a.
A118438

Remove the 2 screws and brush holder.


Hide 5.REMOVE GENERATOR COIL ASSEMBLY

a.
A118439

Remove the 4 bolts.


b.
A115868
1.333,0.594 0.938,0.177 0.938,0.177 0.76,0.177 false 0.469,0.094 0.792,0.25 0.323,0.156 10 false SST 0.208,0.771 0.375,0.948 0.167,0.177 10 false *a
*a Hold
V100135

Turn


Using SST, remove the generator coil.

SST
09950-40011  (09951-04020, 09952-04010, 09953-04020, 09954-04010, 09955-04071, 09957-04010, 09958-04011)


Hide 6.REMOVE GENERATOR ROTOR ASSEMBLY

a.

Remove the washer from the generator rotor.


b.

Remove the drive end frame space collar.


c.

Remove the rotor from the drive end frame.


Hide 7.INSPECT GENERATOR DRIVE END FRAME BEARING

a.
A118440

Check that the bearing is not rough or worn, and that it rotates smoothly.

If necessary, replace the drive end frame bearing.


Hide 8.REMOVE GENERATOR DRIVE END FRAME BEARING

a.
A118441

Remove the 4 screws and bearing retainer.


b.
A118442
1.24,0.917 0.448,0.917 0.448,0.917 1.198,1.302 true 0.156,0.854 0.479,1.031 0.323,0.177 10 false SST

Using SST and a hammer, tap out the bearing.

SST
09950-60010  (09951-00250)
09950-70010  (09951-07100)