CHECK DRIVER SIDE JUNCTION BLOCK ASSEMBLY
| *1 | Integration Relay | - | - |
Disconnect the 2D, 2H and 2L driver side junction block assembly connectors.
Measure the resistance and voltage according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| 2D-9 (GND) - Body ground | W-B - Body ground | Ground | Always | Below 1 Ω |
| 2D-18 (GND) - Body ground | W-B - Body ground | Ground | Always | Below 1 Ω |
| 2H-4 (ALTB) - Body ground | LG - Body ground | Battery power supply | Always | 11 to 14 V |
| 2L-12 (BECU) - Body ground | L - Body ground | Battery power supply | Always | 11 to 14 V |
If the result is not as specified, there may be a malfunction on the wire harness side.
Reconnect the 2D, 2H and 2L driver side junction block assembly connectors.
Measure the voltage according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| 2A-4 (L1) - Body ground | L - Body ground | ·
Power window regulator master switch assembly (door control switch) lock input signal ·
Driver side door key-linked lock input signal |
·
Power window regulator master switch assembly (door control switch) locked ·
Driver side door key cylinder in lock position |
Below 1 V |
·
Power window regulator master switch assembly (door control switch) off ·
Ignition switch off, all doors closed and driver side door key cylinder in neutral position |
11 to 14 V | |||
| 2D-4 (UL1) - Body ground | L-W - Body ground | ·
Power window regulator master switch assembly (door control switch) unlock input signal ·
Driver side door key-linked unlock input signal |
·
Power window regulator master switch assembly (door control switch) unlocked ·
Driver side door key cylinder in unlock position |
Below 1 V |
·
Power window regulator master switch assembly (door control switch) off ·
Ignition switch off, all doors closed and driver side door key cylinder in neutral position |
11 to 14 V | |||
| 2K-10 (ACT-) - Body ground | L-Y - Body ground | Door lock motor unlock drive output signal (passenger door, rear RH*1 or LH*2 door and back door) | Power window regulator master switch assembly (door control switch) not pushed and driver side door key cylinder in neutral position | Below 1 V |
| Lock side of power window regulator master switch assembly (door control switch) pushed, or driver side door key cylinder in unlock position | 11 to 14 V | |||
| 2K-11 (ACT+) - Body ground | L - Body ground | Door lock motor lock drive output signal (passenger door, rear RH*1 or LH*2 door and back door) | Power window regulator master switch assembly (door control switch) not pushed and driver side door key cylinder in neutral position | Below 1 V |
| Lock side of power window regulator master switch assembly (door control switch) pushed, or driver side door key cylinder in lock position | 11 to 14 V | |||
| 2O-27 (DCTY) - Body ground | R-B - Body ground | Front door courtesy light switch assembly LH*1 or RH*2 input signal | Driver side door open | Below 1 V |
| Driver side door closed | 11 to 14 V | |||
| 2R-27 (ACT-) - Body ground | L-Y - Body ground | Door lock motor unlock drive output signal (driver door and rear LH*1 or RH*2 door) | Power window regulator master switch assembly (door control switch) not pushed and driver side door key cylinder in neutral position | Below 1 V |
| Lock side of power window regulator master switch assembly (door control switch) pushed, or driver side door key cylinder in unlock position | 11 to 14 V | |||
| 2R-28 (ACT+) - Body ground | L - Body ground | Door lock motor lock drive output signal (driver door and rear LH*1 or RH*2 door) | Power window regulator master switch assembly (door control switch) not pushed and driver side door key cylinder in neutral position | Below 1 V |
| Lock side of power window regulator master switch assembly (door control switch) pushed, or driver side door key cylinder in lock position | 11 to 14 V |
*1: for LHD
*2: for RHD
If the result is not as specified, the driver side junction block assembly may have a malfunction.
CHECK THEFT WARNING ECU ASSEMBLY (w/ Theft Deterrent System)
Disconnect the G124 theft warning ECU assembly connector.
Measure the resistance and voltage according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| G124-1 (E) - Body ground | W-B - Body ground | Ground | Always | Below 1 Ω |
| G124-3 (+B1) - Body ground | L-Y - Body ground | Battery power supply | Always | 11 to 14 V |
| G124-4 (IG) - Body ground | R-L - Body ground | Ignition power supply | Ignition switch off | Below 1 V |
| Ignition switch ON | 11 to 14 V | |||
| G124-12 (+B2) Body ground | LG - Body ground | Battery power supply | Always | 11 to 14 V |
If the result is not as specified, there may be a malfunction on the wire harness side.
Reconnect the G124 theft warning ECU assembly connector.
Measure the voltage according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| G124-7 (CTY) - Body ground | R-L - Body ground | All Door courtesy switches input signal | One or more doors open | Below 1 V |
| All doors closed | 11 to 14 V | |||
| G124-11 (DDUL) - Body ground | L-Y - Body ground | Driver side door unlock output signal | Transmitter unlock switch pressed | Pulse generation |
If the result is not as specified, the theft warning ECU assembly may have a malfunction.