Home › Vehicle Interior › DOOR LOCK › WIRELESS DOOR LOCK CONTROL SYSTEM(w/ Theft Deterrent System)
RM1880E _58 Vehicle Interior _013237 DOOR LOCK _0068605 WIRELESS DOOR LOCK CONTROL SYSTEM(w/ Theft Deterrent System) U

DOOR LOCK  WIRELESS DOOR LOCK CONTROL SYSTEM(w/ Theft Deterrent System)  TERMINALS OF ECU  


CHECK THEFT WARNING ECU ASSEMBLY


a.
B291953
1.563,0.146 1.979,0.396 0.417,0.25 1.604,0.188 1.979,0.406 0.375,0.219 10 false G124

Disconnect the G124 theft warning ECU assembly connector.


b.

Measure the resistance and voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G124-1 (E) - Body ground W-B - Body ground Ground Always Below 1 Ω
G124-3 (+B1) - Body ground L-Y - Body ground Battery power supply Always 11 to 14 V
G124-4 (IG) - Body ground R-L - Body ground Ignition power supply Ignition switch off Below 1 V
Ignition switch ON 11 to 14 V
G124-12 (+B2) - Body ground LG - Body ground Battery power supply Always 11 to 14 V

If the result is not as specified, there may be a malfunction on the wire harness side.



c.

Reconnect the G124 theft warning ECU assembly connector.


d.

Measure the resistance and voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G124-2 (DMLP) - Body ground P - Body ground Interior lights output signal Interior lights on Below 1 V
Interior lights off 11 to 14 V
G124-5 (KSW) - Body ground G-Y - Body ground Unlock warning switch input signal No key in ignition key cylinder 10 kΩ or higher
Key inserted in ignition key cylinder Below 1 Ω
G124-7 (CTY) - Body ground R-L - Body ground All door courtesy switches input signal One or more doors are open Below 1 V
All doors are closed 11 to 14 V
G124-11 (DDUL) - Body ground L-Y - Body ground Driver side door unlock output signal Transmitter unlock switch pressed Pulse generation
G124-18 (BRK-) - Body ground V-R - Body ground Door control receiver input signal Ignition switch off, all doors closed and transmitter switch not pressed 11 to 14 V
Ignition switch off, all doors closed and transmitter switch pressed Pulse generation
G124-19 (BRK+) - Body ground G-W - Body ground Door control receiver output signal Key inserted in ignition key cylinder → As key pulled out of ignition key cylinder 11 to 14 V → Pulse generation → 11 to 14 V
G124-20 (L2) - Body ground L - Body ground Door lock output signal Ignition switch off, all doors closed and transmitter switch not pressed Below 1 V
Ignition switch off, all doors closed and transmitter lock switch pressed Pulse generation
G124-21 (UL3) -Body ground L-W - Body ground Door unlock output signal Ignition switch off, all doors closed and transmitter switch not pressed Below 1 V
Ignition switch off, all doors closed and transmitter unlock switch pressed Pulse generation
G124-23 (HAZD) - Body ground G-O - Body ground All hazard warning light output signals Hazard warning signal switch assembly off 11 to 14 V
Hazard warning signal switch assembly on Below 1 V
G124-26 (SH-) - Body ground B - Body ground Security horn output signal Security horn assembly off Below 1 V
Security horn assembly on Pulse generation

If the result is not as specified, the theft warning ECU assembly may have a malfunction.




CHECK DRIVER SIDE JUNCTION BLOCK ASSEMBLY


B276157
0.917,3.167 1.333,3.417 0.417,0.25 0.917,4.333 1.333,4.583 0.417,0.25 0.833,5.5 1.25,5.75 0.417,0.25 1.333,5.5 1.75,5.75 0.417,0.25 1.833,5.5 2.25,5.75 0.417,0.25 2.333,5.5 2.75,5.75 0.417,0.25 2.833,5.5 3.25,5.75 0.417,0.25 3.167,6.25 3.583,6.5 0.417,0.25 3.667,6.25 4.083,6.5 0.417,0.25 4.167,6.25 4.583,6.5 0.417,0.25 4.667,6.25 5.083,6.5 0.417,0.25 5.167,6.25 5.583,6.5 0.417,0.25 5.667,6.25 6.083,6.5 0.417,0.25 2.5,4.333 2.917,4.583 0.417,0.25 4.083,4.333 4.5,4.583 0.417,0.25 5.75,4.333 6.167,4.583 0.417,0.25 2.5,3.167 2.917,3.417 0.417,0.25 4.083,3.167 4.5,3.417 0.417,0.25 5.75,3.167 6.167,3.417 0.417,0.25 0.906,1.594 1.052,1.594 1.052,1.594 1.302,1.781 true 5.354,2.083 5.208,2.083 5.208,2.083 5.01,1.833 true 1.042,3.208 1.281,3.385 0.24,0.177 10 false 2A 1.688,0.542 1.927,0.719 0.24,0.177 10 false 2A 1.667,0.99 1.927,1.188 0.26,0.198 10 false 2B 1.042,4.385 1.281,4.563 0.24,0.177 10 false 2E 1.458,1.698 1.75,1.917 0.292,0.219 10 false 2E 0.708,1.51 0.979,1.708 0.271,0.198 10 false 2F 0.979,5.542 1.219,5.719 0.24,0.177 10 false 2I 2.063,1.542 2.25,1.771 0.188,0.229 10 false 2I 2.313,1.542 2.5,1.771 0.188,0.229 10 false 2J 2.042,2.292 2.344,2.51 0.302,0.219 10 false 2K 2.313,2.292 2.51,2.51 0.198,0.219 10 false 2L 2.542,2.292 2.844,2.51 0.302,0.219 10 false 2M 4.219,0.792 4.51,1.021 0.292,0.229 10 false 2N 4.552,0.792 4.844,1.021 0.292,0.229 10 false 2O 4.229,1.542 4.5,1.75 0.271,0.208 10 false 2P 4.542,1.542 4.833,1.74 0.292,0.198 10 false 2Q 4.219,2.292 4.51,2.49 0.292,0.198 10 false 2R 4.552,2.292 4.844,2.49 0.292,0.198 10 false 2S 1.479,5.542 1.719,5.719 0.24,0.177 10 false 2J 1.969,5.542 2.208,5.719 0.24,0.177 10 false 2K 2.469,5.542 2.708,5.719 0.24,0.177 10 false 2L 2.958,5.542 3.198,5.719 0.24,0.177 10 false 2M 3.302,6.292 3.542,6.469 0.24,0.177 10 false 2N 3.792,6.292 4.031,6.469 0.24,0.177 10 false 2O 4.292,6.302 4.531,6.479 0.24,0.177 10 false 2P 4.792,6.292 5.031,6.469 0.24,0.177 10 false 2Q 5.292,6.292 5.531,6.469 0.24,0.177 10 false 2R 5.792,6.292 6.031,6.469 0.24,0.177 10 false 2S 2.635,4.385 2.875,4.563 0.24,0.177 10 false 2F 4.219,4.375 4.458,4.552 0.24,0.177 10 false 2G 1.208,2.052 1.51,2.26 0.302,0.208 10 false 2G 5.865,4.375 6.104,4.552 0.24,0.177 10 false 2H 1.219,2.406 1.521,2.604 0.302,0.198 10 false 2H 2.625,3.208 2.865,3.385 0.24,0.177 10 false 2B 4.208,3.219 4.448,3.396 0.24,0.177 10 false 2C 1.719,1.313 1.958,1.49 0.24,0.177 10 false 2C 1.313,1.354 1.552,1.531 0.24,0.177 10 false 2D 5.875,3.208 6.115,3.385 0.24,0.177 10 false 2D 5.406,2 5.667,2.24 0.26,0.24 10 false *1
*1 Integration Relay - -


a.

Disconnect the 2D, 2H and 2L driver side junction block assembly connectors.


b.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
2D-9 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω
2D-18 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω
2H-4 (ALTB) - Body ground LG - Body ground Battery power supply Always 11 to 14 V
2L-12 (BECU) - Body ground L - Body ground Battery power supply Always 11 to 14 V

If the result is not as specified, there may be a malfunction on the wire harness side.



c.

Reconnect the 2D, 2H and 2L driver side junction block assembly connectors.


d.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
2A-4 (L1) - Body ground L - Body ground
·

Power window regulator master switch assembly (door control switch) lock input signal

·

Driver side door key-linked lock input signal


·

Power window regulator master switch assembly (door control switch) locked

·

Driver side door key cylinder in lock position


Below 1 V
·

Power window regulator master switch assembly (door control switch) off

·

Ignition switch off, all doors closed and driver side door key cylinder in neutral position


11 to 14 V
2D-4 (UL1) - Body ground L-W - Body ground
·

Power window regulator master switch assembly (door control switch) unlock input signal

·

Driver side door key-linked unlock input signal


·

Power window regulator master switch assembly (door control switch) unlocked

·

Driver side door key cylinder in unlock position


Below 1 V
·

Power window regulator master switch assembly (door control switch) off

·

Ignition switch off, all doors closed and driver side door key cylinder in neutral position


11 to 14 V
2K-10 (ACT-) - Body ground L-Y - Body ground Door lock motor unlock drive output signal (passenger door, rear LH door and back door) Power window regulator master switch assembly (door control switch) not pushed and driver side door key cylinder in neutral position Below 1 V
Lock side of power window regulator master switch assembly (door control switch) pushed, or driver side door key cylinder in unlock position 11 to 14 V
2K-11 (ACT+) - Body ground L - Body ground Door lock motor lock drive output signal (passenger door, rear LH door and back door) Power window regulator master switch assembly (door control switch) not pushed and driver side door key cylinder in neutral position Below 1 V
Power window regulator master switch assembly (door control switch) or driver side door key cylinder in lock position 11 to 14 V
2O-27 (DCTY) - Body ground R-B - Body ground Front door courtesy light switch assembly RH input signal Driver side door open Below 1 V
Driver side door closed 11 to 14 V
2R-27 (ACT-) - Body ground L-Y - Body ground Door lock motor unlock drive output signal (driver door and rear RH door) Power window regulator master switch assembly (door control switch) not pushed and driver side door key cylinder in neutral position Below 1 V
Lock side of power window regulator master switch assembly (door control switch) pushed, or driver side door key cylinder in unlock position 11 to 14 V
2R-28 (ACT+) - Body ground L - Body ground Door lock motor lock drive output signal (driver door and rear RH door) Power window regulator master switch assembly (door control switch) not pushed and driver side door key cylinder in neutral position Below 1 V
Power window regulator master switch assembly (door control switch) or driver side door key cylinder in lock position 11 to 14 V

If the result is not as specified, the driver side junction block assembly may have a malfunction.