Home › Vehicle Interior › DOOR LOCK › WIRELESS DOOR LOCK CONTROL SYSTEM(w/ Theft Deterrent System)
RM1880E _58 Vehicle Interior _013237 DOOR LOCK _0068605 WIRELESS DOOR LOCK CONTROL SYSTEM(w/ Theft Deterrent System) A

DOOR LOCK  WIRELESS DOOR LOCK CONTROL SYSTEM(w/ Theft Deterrent System)  CUSTOMIZE PARAMETERS  


PROCEDURE

Hide 1.CUSTOMIZE WIRELESS DOOR LOCK CONTROL SYSTEM

HINT:
·

The following items can be customized.

·

During customize mode, the alarm control functions are disabled.

·

During customize mode, the following wireless control functions are disabled: remote alarm function, automatic locking function, operation stop function and illuminated entry function.

·

During customize mode, the ECU will not output lock/unlock signals.

·

While in customize mode, if the key is inserted into the ignition key cylinder or a door is opened, customize mode will be canceled.



NOTICE:
·

When the customer requests a change in a function, first make sure that the function can be customized.

·

Record the current settings before customizing.



a.

Customizing with manual operation

Display Default Content Setting Relevant ECU
Wireless answer-back function Only hazard warning lights flash Function that makes the hazard warning lights and side turn signal lights flash and security horn assembly sound for answer-back when the door control transmitter assembly lock/unlock switch pressed Only hazard warning lights and side turn signal lights flash, Hazard warning lights and side turn signal lights flash and security horn assembly sounds or OFF Theft warning ECU assembly
Door ajar warning function ON (security horn assembly sounds) If door is not completely closed and the lock switch on door control transmitter assembly is pressed, this function sounds security horn assembly for 1 second ON or OFF Theft warning ECU assembly

i.

Check that the following conditions are met.

·

No key is in the ignition key cylinder.

·

The theft deterrent system is in the disarmed state (when either condition below is met):

·

All the doors are in the unlocked condition and the doors are locked and unlocked using the door control transmitter assembly.

·

The key is inserted into the ignition key cylinder, the ignition switch is turned to ON then off, and then the key is removed.


·

The driver side door is opened (the other doors are closed).



ii.

Perform the following operation twice within 5 seconds:

1.

Insert the key into the ignition key cylinder, and then pull it out (ending with the key pulled out).



iii.

Wait for 5 seconds.


iv.

After completing the above step, press and hold down lock switch and unlock switch on the door control transmitter assembly at the same time for over 3 seconds within 5 seconds.


v.

Check that the hazard warning lights flash once.


vi.

After completing the lock and unlock switch operation, perform the following operation within 5 seconds.

1.

Press the lock switch on door control transmitter assembly once within 2seconds.



vii.

After completing the above step, press the unlock switch on door control transmitter assembly once within 2 seconds.


viii.

Check that the hazard warning lights flash once.


ix.

After completing the unlock switch operation, perform the following operations (mode select) within 10 seconds:

1.

Press the lock switch on door control transmitter assembly the number of times shown below depending on the desired function behavior to select the answer-back pattern and warning function setting. Press the unlock switch on door lock transmitter once within 2 seconds of pressing the lock switch on door control transmitter assembly.

Pattern 1
·

Wireless Answer-back Function: Only hazard warning lights and side turn signal lights flash

Door Ajar Warning Function: ON

1.

Press the lock switch on door control transmitter assembly once.



Pattern 2
·

Wireless Answer-back Function: Hazard warning lights and side turn signal lights flash and security horn assembly sounds

Door Ajar Warning Function: ON

1.

Press the lock switch on door control transmitter assembly twice.



Pattern 3
·

Wireless Answer-back Function: OFF

Door Ajar Warning Function: OFF

1.

Press the lock switch on door control transmitter assembly 3 times.





x.

Check the response to the customize operation.

Response to Customize Operation Setting
Wireless Answer-back Function Door Ajar Warning Function
Hazard warning lights flash once Only hazard warning lights and side turn signal lights flash ON
Hazard warning lights flash twice Hazard warning lights and side turn signal lights flash and security horn assembly sounds ON
Hazard warning lights flash 3 times OFF OFF