Home › Vehicle Interior › DOOR LOCK › WIRELESS DOOR LOCK CONTROL SYSTEM(w/o Theft Deterrent System)
RM1880E _58 Vehicle Interior _013237 DOOR LOCK _0068607 WIRELESS DOOR LOCK CONTROL SYSTEM(w/o Theft Deterrent System) M

DOOR LOCK  WIRELESS DOOR LOCK CONTROL SYSTEM(w/o Theft Deterrent System)  REGISTRATION  


PROCEDURE

Hide 1. DESCRIPTION OF CODE REGISTRATION

HINT:
·

Recognition code registration is necessary when replacing the door control transmitter assembly or the door control receiver.

·

Add mode is used to register new recognition codes while retaining codes already registered. This mode is used when a new transmitter is added. If the number of registered codes exceeds 4, the previously registered codes will be erased in order, starting from the first registered code.

·

Rewrite mode is used to erase all previously registered recognition codes in order to register new recognition codes. This mode is used when the transmitter or the receiver is replaced.

·

Confirmation mode is used to confirm how many recognition codes have already been registered before another recognition code is registered.

·

Prohibition mode is used to erase all the registered codes and disable the wireless door lock function. This mode is used when the transmitter is lost.

·

All of the following registration procedures must be performed in order.



Hide 2. REGISTER RECOGNITION CODE

a.

Check that the following conditions are met.

·

No key in the ignition key cylinder.

·

The driver side door is opened (the other doors are closed).



b.

Insert the key into the ignition key cylinder, then pull it out twice within 5 seconds.


c.

Perform the following operations within 40 seconds.

i.

Close and open the driver side door twice.


ii.

Insert the key into the ignition key cylinder, then pull it out.


iii.

Close and open driver side door twice.



d.

Perform the following operations within 40 seconds.

i.

Close and open the driver side door twice.


ii.

Insert the key into the ignition key cylinder and close the driver side door.



e.

Perform the following operations within 40 seconds.

i.

Operate the ignition switch according to the number of times shown below.

B111914
0.24,0.833 1.01,1.083 0.771,0.25 10 Add Mode 0.083,0.083 3.115,0.271 3.031,0.188 10 Number of On-Off operations of ignition switch: 1.5,0.833 3.083,1.052 1.583,0.219 10 On-Off operation: Once 0.583,1.583 0.833,1.781 0.25,0.198 10 On 0.573,1.917 0.844,2.115 0.271,0.198 10 Off 4.083,1.573 4.396,1.771 0.313,0.198 10 On 4.083,1.917 4.406,2.115 0.323,0.198 10 Off 0.583,3.594 0.833,3.833 0.25,0.24 10 On 0.573,3.927 0.844,4.167 0.271,0.24 10 Off 4.083,3.604 4.313,3.781 0.229,0.177 10 On 4.073,3.938 4.313,4.177 0.24,0.24 10 Off 1.292,1.24 1.479,1.417 0.188,0.177 10 T1 3.75,0.833 4.646,1.01 0.896,0.177 10 Rewrite Mode 5,0.833 6.615,1.052 1.615,0.219 10 On-Off operation: Twice 4.792,1.24 5.083,1.417 0.292,0.177 10 T1 5,1.24 5.25,1.417 0.25,0.177 10 T1 0.229,2.833 1.427,3.01 1.198,0.177 10 Confirmation Mode 1.5,2.833 3.208,3.052 1.708,0.219 10 On-Off operation: 3 times 4.771,3.24 5,3.417 0.229,0.177 10 T1 4.99,3.24 5.25,3.417 0.26,0.177 10 T1 1.26,3.24 1.5,3.417 0.24,0.177 10 T1 1.469,3.24 1.75,3.417 0.281,0.177 10 T1 3.75,2.833 4.948,3.01 1.198,0.177 10 Prohibition Mode 5,2.833 6.688,3.083 1.688,0.25 10 On-Off operation: 5 times 5.094,4.333 6.521,4.521 1.427,0.188 10 T1: Approx. 1 second

HINT:

If the number of ignition switch On-Off operations is 0, 4, 6, or more, there will be no response (power door lock and unlock operation) to show which mode has been selected.



ii.

Remove the key from the ignition key cylinder.



f.

Check the response to the selected mode within 3 seconds.

B111913
0.229,1.427 1.042,1.635 0.813,0.208 10 false Add Mode 1.5,1.427 3.552,1.646 2.052,0.219 10 false Lock-Unlock operation: Once 0.469,2.229 0.958,2.448 0.49,0.219 10 false Lock 0.344,2.552 0.927,2.781 0.583,0.229 10 false Unlock 0.469,4.552 1,4.781 0.531,0.229 10 false Lock 0.344,4.865 0.948,5.104 0.604,0.24 10 false Unlock 0.479,6.635 0.917,6.833 0.438,0.198 10 false Lock 0.354,6.969 0.906,7.177 0.552,0.208 10 false Unlock 3.99,2.229 4.396,2.458 0.406,0.229 10 false Lock 3.865,2.552 4.417,2.813 0.552,0.26 10 false Unlock 1.292,1.917 1.594,2.135 0.302,0.219 10 false T1 3.74,1.427 4.771,1.667 1.031,0.24 10 false Rewrite Mode 5.021,1.417 7.125,1.635 2.104,0.219 10 false Lock-Unlock operation: Twice 4.792,1.917 5.052,2.135 0.26,0.219 10 false T1 5,1.917 5.271,2.156 0.271,0.24 10 false T1 0.083,0.115 3.583,0.385 3.5,0.271 10 false Response to selected mode (power door lock operation): 0.083,0.573 6.49,0.99 6.406,0.417 10 false Driver side junction block assembly automatically performs power door Lock-Unlock operations to indicate which mode has been selected. 0.229,3.458 1.427,3.635 1.198,0.177 10 false Confirmation Mode 1.5,3.448 6.073,3.667 4.573,0.219 10 false Lock-Unlock operation: The number of registered codes (1 to 5 times) 1.375,4.26 1.656,4.469 0.281,0.208 10 false T2 1.771,4.26 2.063,4.51 0.292,0.25 10 false T2 1.26,6.323 1.448,6.5 0.188,0.177 10 false T1 1.469,6.323 1.656,6.5 0.188,0.177 10 false T1 1.406,3.844 1.969,4.042 0.563,0.198 10 false 1st Time 2.188,3.844 2.792,4.042 0.604,0.198 10 false 2nd Time 0.229,5.771 1.427,5.948 1.198,0.177 10 false Prohibition Mode 1.5,5.781 3.656,6.01 2.156,0.229 10 false Lock-Unlock operation: 5 times 5.615,6.865 7.156,7.135 1.542,0.271 10 false T1: Approx. 1 second 5.615,7.094 7.156,7.354 1.542,0.26 10 false T2: Approx. 2 seconds

HINT:
·

In the confirmation mode, Lock-Unlock operation will occur once for each recognition code that has been registered. For example, if 2 recognition codes have been registered, the Lock-Unlock operation will occur 2 times.

·

In confirmation mode, if no recognition codes have been registered, the Lock-Unlock operation will occur 5 times.

·

If confirmation mode or prohibition mode is selected, the operation ends after the response to the selected mode completes.




g.

Within 40 seconds of completing the confirmation mode operation, press the lock and unlock switches on the transmitter simultaneously.


h.

After completing the above step, press a single switch (lock or unlock) within 5 seconds.


i.

After completing the above step, check the response to the registration completion within 3 seconds.

B111915
0.229,1.427 2.115,1.604 1.885,0.177 10 false Lock-Unlock Occurs Once 4.115,1.427 6.031,1.604 1.917,0.177 10 false Lock-Unlock Occurs Twice 0.479,2.813 0.906,3.052 0.427,0.24 10 false Lock 0.354,3.135 0.885,3.385 0.531,0.25 10 false Unlock 4.354,2.813 4.813,3.042 0.458,0.229 10 false Lock 4.229,3.135 4.76,3.385 0.531,0.25 10 false Unlock 1.292,2.5 1.625,2.74 0.333,0.24 10 false T1 5.167,2.479 5.448,2.708 0.281,0.229 10 false T1 5.375,2.479 5.646,2.698 0.271,0.219 10 false T1 0.083,0.135 2.51,0.354 2.427,0.219 10 false Response to registration completion: 5.344,3.448 6.854,3.667 1.51,0.219 10 false T1: Approx. 1 second 0.208,0.646 6.938,1.031 6.729,0.385 10 false Driver side junction block assembly automatically performs power door Lock-Unlock operation to show whether registration has been completed correctly or not. 0.188,1.958 2.396,2.375 2.208,0.417 10 false Registration of recognition code has been completed. 4.073,1.958 6.26,2.375 2.188,0.417 10 false Registration of recognition code has failed.

HINT:
·

If the registration of the recognition code has failed, perform the registration procedures from the beginning.

·

If registering another transmitter, repeat the procedures after the response to the selected mode confirmation. All 4 recognition codes can be registered consecutively.




j.

Perform either of the following.

i.

Open the door.


ii.

Insert the key into the ignition key cylinder.



k.

Registration of the recognition codes (add mode and rewrite mode) is completed.