Home › Vehicle Interior › DOOR LOCK › FRONT DOOR LOCK
RM1880E _58 Vehicle Interior _013237 DOOR LOCK _0068611 FRONT DOOR LOCK G

DOOR LOCK  FRONT DOOR LOCK  INSPECTION  


PROCEDURE

Hide 1.INSPECT FRONT DOOR LOCK ASSEMBLY LH

B277598
4.896,1.458 4.323,1.625 true 5.656,1.458 6.167,1.625 true 2.354,2.156 2.604,2.417 0.25,0.26 10 false *a 1.875,2.469 2.146,2.688 0.271,0.219 10 false *b 4.583,0.521 4.875,0.781 0.292,0.26 10 false *c 6.188,1.563 6.5,1.771 0.313,0.208 10 false UL 4.198,1.563 4.479,1.76 0.281,0.198 10 false L
*a Lock *b Unlock
*c Component without harness connected
(Front Door Lock Assembly LH)
- -


a.

Check the door lock motor operation.

i.

Apply battery voltage to the motor connector and check the operation of the door lock motor.

OK:
Measurement Condition Specified Condition
Battery positive (+) → Terminal 4 (L)
Battery negative (-) → Terminal 1 (UL)
Lock
Battery positive (+) → Terminal 1 (UL)
Battery negative (-) → Terminal 4 (L)
Unlock


If the result is not as specified, replace the front door lock assembly LH.




b.

Check the door lock and unlock switch.

B292264
2.604,0.615 2.823,0.802 0.219,0.188 10 *a 2.396,1.073 2.615,1.26 0.219,0.188 10 *b 2.854,1.427 3.073,1.615 0.219,0.188 10 *c 4.5,0.344 4.719,0.531 0.219,0.188 10 *d
*a Unlock *b Off
*c Lock *d Component without harness connected
(Front Door Lock Assembly LH)


i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
6 (L) - 8 (E) Lock Below 1 Ω
6 (L) - 8 (E)
5 (UL) - 8 (E)
Off 10 kΩ or higher
5 (UL) - 8 (E) Unlock Below 1 Ω


If the result is not as specified, replace the front door lock assembly LH.




Hide 2.INSPECT FRONT DOOR LOCK ASSEMBLY RH

B277600
5.677,1.469 6.052,1.552 true 4.906,1.448 4.208,1.625 true 5.177,1.667 5.125,2.135 true 5.385,1.656 5.656,2.125 true 1.26,2.115 1.5,2.344 0.24,0.229 10 *a 1.823,2.479 2.073,2.698 0.25,0.219 10 *b 4.594,0.521 4.792,0.708 0.198,0.188 10 *c 6.125,1.51 6.5,1.75 0.375,0.24 10 UL 4.094,1.583 4.469,1.823 0.375,0.24 10 L 5.5,2.167 5.99,2.406 0.49,0.24 10 LSSR 5.083,2.167 5.313,2.417 0.229,0.25 10 E
*a Unlock *b Lock
*c Component without harness connected
(Front Door Lock Assembly RH)
- -


a.

Check the door lock motor operation.

i.

Apply battery voltage to the door lock motor connector and check the operation of the door lock motor.

OK:
Measurement Condition Specified Condition
Battery positive (+) → Terminal 4 (L)
Battery negative (-) → Terminal 1 (UL)
Lock
Battery positive (+) → Terminal 1 (UL)
Battery negative (-) → Terminal 4 (L)
Unlock


If the result is not as specified, replace the front door lock assembly RH.




b.

Check the detection switch.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
7 (LSSR) - 8 (E) Lock 10 kΩ or higher
Unlock Below 1 Ω


If the result is not as specified, replace the front door lock assembly RH.