Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENGINE IMMOBILISER SYSTEM
RM1880E _58 Vehicle Interior _013238 THEFT DETERRENT / KEYLESS ENTRY _0068615 ENGINE IMMOBILISER SYSTEM C

THEFT DETERRENT / KEYLESS ENTRY  ENGINE IMMOBILISER SYSTEM  B2780  Push Switch / Key Unlock Warning Switch Malfunction  


DESCRIPTION

This DTC is stored if the transponder key ECU assembly does not detect that the unlock warning switch assembly is on even when the ignition switch is ON. Under normal conditions, the unlock warning switch assembly is on when the ignition switch is ON.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Note
B2780 Push Switch / Key Unlock Warning Switch Malfunction The unlock warning switch assembly is not detected as being on when the ignition switch is ON (1 trip detection logic*).
·

Unlock warning switch assembly

·

Harness or connector

·

Transponder key ECU assembly


Transponder Key ECU Assembly
DTC Output Confirmation Operation

Insert the key into the ignition key cylinder.



*: Only output while a malfunction is present.


Vehicle Condition and Fail-safe Operation when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Operation when Malfunction Detected
Engine cannot be started. -

Related Data List and Active Test
DTC Code Data List and Active Test
B2780 Key SW

WIRING DIAGRAM

B285884
5.677,0.854 6.51,1.302 0.833,0.448 10 false KSW 5.042,1.646 5.656,2.333 0.615,0.688 10 false G26 5.042,1.792 7.115,2.5 2.073,0.708 10 false Transponder Key ECU Assembly 2.406,1.125 3.344,1.823 0.938,0.698 10 false G10 2.406,1.26 4.76,2 2.354,0.74 10 false Unlock Warning Switch Assembly 5.479,0.76 5.958,1.115 0.479,0.354 10 false 3 3.781,0.76 4.365,1.219 0.583,0.458 10 false UN+ 4.135,0.76 4.594,1.146 0.458,0.385 10 false 1 2.74,0.76 3.25,1.083 0.51,0.323 10 false UN- 2.563,0.76 2.823,1.042 0.26,0.281 10 false 2

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the transponder key ECU assembly, refer to the Service Bulletin.

·

After performing repairs, perform the operation that fulfills the DTC output confirmation operation, and then confirm that no DTCs are output again.



PROCEDURE

1.CLEAR DTC
a.

Clear the DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENGINE IMMOBILISER SYSTEM>DTC CHECK / CLEAR

Body Electrical > Immobiliser > Clear DTCs
50002 260

Result:
Proceed to
NEXT



NEXT

2.CHECK FOR DTC
2.CHECK FOR DTC
a.

Check for DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENGINE IMMOBILISER SYSTEM>DTC CHECK / CLEAR

Body Electrical > Immobiliser > Trouble Codes
50001 260
OK:

DTC B2780 is not output.



Result:
Proceed to
OK
NG



OK

NG

3.INSPECT UNLOCK WARNING SWITCH ASSEMBLY
3.INSPECT UNLOCK WARNING SWITCH ASSEMBLY
a.

Remove the unlock warning switch assembly.

Click hereVehicle Interior>DOOR LOCK>UNLOCK WARNING SWITCH>REMOVAL


b.
B274206
0.615,1.135 0.865,1.417 0.25,0.281 10 false *a 1.229,1.396 1.552,1.75 0.323,0.354 10 false *b
*a Pushed
*b Not pushed


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
1 - 2 Pushed Below 1 Ω
Not pushed 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (UNLOCK WARNING SWITCH - TRANSPONDER KEY ECU AND BODY GROUND)

NG

REPLACE UNLOCK WARNING SWITCH ASSEMBLY

4.CHECK HARNESS AND CONNECTOR (UNLOCK WARNING SWITCH - TRANSPONDER KEY ECU AND BODY GROUND)
a.

Disconnect the G10 unlock warning switch assembly connector.


b.

Disconnect the G26 transponder key ECU assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G10-1 (UN+) - G26-3 (KSW) Always Below 1 Ω
G10-1 (UN+) or G26-3 (KSW) - Body ground Always 10 kΩ or higher
G10-2 (UN-) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE TRANSPONDER KEY ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR