Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENGINE IMMOBILISER SYSTEM
RM1880E _58 Vehicle Interior _013238 THEFT DETERRENT / KEYLESS ENTRY _0068615 ENGINE IMMOBILISER SYSTEM U

THEFT DETERRENT / KEYLESS ENTRY  ENGINE IMMOBILISER SYSTEM  DATA LIST / ACTIVE TEST  


DATA LIST


HINT:
·

Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

·

If the ignition switch cannot be turned to ON, communication with the intelligent tester can be performed by connecting the intelligent tester to the vehicle and turning a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the intelligent tester and vehicle begins.



NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Immobiliser / Data List.


e.

According to the display on the intelligent tester, read the Data List.

Body Electrical > Immobiliser > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
D Door Courtesy SW Driver side door courtesy light switch ON or OFF ON: Driver side door open
OFF: Driver side door closed
-
Key SW Unlock warning switch signal ON or OFF ON: Key inserted in ignition key cylinder
OFF: No key in ignition key cylinder
-
IG SW Ignition switch signal ON or OFF ON: Ignition switch ON
OFF: Ignition switch ACC or off
HINT:

*2


Immobiliser Engine immobiliser system status determined by transponder key ECU assembly Set or Unset Set: Engine immobiliser set (engine start prohibited [no key in ignition key cylinder])
Unset: Engine immobiliser unset (engine start permitted [key inserted in ignition key cylinder])
When the engine immobiliser system does not change to the unset state, this item can be used to determine if the cause is the transponder key ECU assembly.
HINT:

*2


Response Key response to signal from transponder key ECU assembly OK or NG OK: Key responds to signal from transponder key ECU assembly
NG: Key does not respond to signal from transponder key ECU assembly
Problems may be caused by the following:
·

A key from a different vehicle is being used.

·

Malfunctions in the key, transponder key ECU assembly or transponder key amplifier.


Frame Error State of data sent from key OK or NG OK: No problem with data sent from key
NG: Problem with data sent from key
Problems may be caused by the following:
·

Communication errors due to external electric wave noise.

·

Malfunctions in the key, transponder key ECU assembly or transponder key amplifier.


Different Serial Number Vehicle serial number OK or NG OK: Signal from transponder chip and vehicle serial number stored in transponder key ECU assembly match
NG: Signal from transponder chip and vehicle serial number stored the transponder key ECU assembly do not match
Problems may be caused by the following:
·

A key from a different vehicle is being used.

·

Malfunctions in the key, transponder key ECU assembly or transponder key amplifier.


HINT:

*1


Different Encrypt Code Code status between transponder chip and transponder key ECU assembly OK or NG OK: Codes of transponder chip and transponder key ECU assembly match
NG: Codes of transponder chip and transponder key ECU assembly do not match
Problems may be caused by the following:
·

A key from a different vehicle is being used.

·

Malfunctions in the key, transponder key ECU assembly or transponder key amplifier.


HINT:

*1


Abnormal Status Transponder chip status signal OK or NG OK: Transponder chip status signal normal
NG: Transponder chip status signal malfunction (malfunction in code computation in key/transponder key ECU assembly)
Problems may be caused by the following:
·

Communication errors due to external electric wave noise (LF).

·

Malfunctions in the key, transponder key ECU assembly or transponder key amplifier.


HINT:

*1


Bcc Malfunction BCC signal status of transponder chip OK or NG OK: BCC signal normal
NG: BCC signal malfunction (malfunction in code computation in key/transponder key ECU assembly)
Problems may be caused by the following:
·

Communication errors due to external electric wave noise (LF).

·

Malfunctions in the key, transponder key ECU assembly or transponder key amplifier.


HINT:

*1


Sub Key Whether sub-key ID code matches ID code registered in transponder key ECU assembly Reg or Unreg Reg: ID code of sub-key matches ID code registered in transponder key ECU assembly
Unreg: ID code of sub-key does not match ID code registered in transponder key ECU assembly
-
Master Key Whether master key ID code matches ID code registered in transponder key ECU assembly Reg or Unreg Reg: ID code of master key matches ID code registered in transponder key ECU assembly
Unreg: ID code of master key does not match ID code registered in transponder key ECU assembly
-
Transponder S-code Number of registered sub-keys min.: 0, max.: 3 Number of registered sub-keys -
Transponder M-code Number of registered master keys min.: 0, max.: 5 Number of registered master keys -
Reg Code Space Full Key registration code memory space full Yes or No No: Possible to register more key codes
Yes: Cannot register any more key codes
-
+B +B judgment Normal or Break Normal: Battery power supply normal
Break: Battery power supply malfunctioning
-
Antenna Coil Status Antenna coil condition Normal or Fail Normal: Antenna coil normal
Fail: Antenna coil malfunctioning
-
EEPROM Status EEPROM status OK or NG OK: Data OK
NG: Data error
-
E/G Start Permission Engine start permission OK or NG OK: Engine start permitted
NG: Engine start not permitted
HINT:

*2


Immobi ECU Comm Spd Immobiliser ECU communication speed Unknown, 50bps, 200bps or No Res Unknown: ECU communication speed unknown
50bps: ECU communication speed 50 bps
200bps: ECU communication speed 200 bps
No Res: No response regarding ECU communication speed
-
The Number of DTCs Number of DTCs Min.: 0, Max.: 255 Number of stored DTCs -
HINT:
·

*1: This indicates that there is a problem with the communication format between the key and transponder key ECU assembly. Electric wave interference, key or transponder key ECU assembly malfunctions, the key of another vehicle being used, etc. are possible causes.

·

*2: Refer to the following Data List items of an actual vehicle.

B263033
0.792,0.479 1.719,0.844 0.927,0.365 10 false IG SW 0.792,1.146 1.823,1.5 1.031,0.354 10 false Immobiliser 0.792,1.813 2.396,2.063 1.604,0.25 10 false E/G Start Permission 2.333,1.24 2.958,1.656 0.625,0.417 10 false Unset 2.427,1.542 2.979,1.896 0.552,0.354 10 false Set 2.427,0.521 2.885,0.802 0.458,0.281 10 false ON 2.427,0.833 2.875,1.146 0.448,0.313 10 false OFF 2.427,1.885 3.01,2.24 0.583,0.354 10 false NG 2.427,2.219 2.958,2.552 0.531,0.333 10 false OK 3.323,0.073 3.646,0.385 0.323,0.313 10 false *1 4.875,0.063 5.219,0.427 0.344,0.365 10 false *3 3.792,0.063 4.104,0.333 0.313,0.271 10 false *2



*1: Without depressing the brake pedal (for Automatic Transmission) or clutch pedal (for Manual Transmission), insert the key into the ignition key cylinder and turn the ignition switch to ACC.

*2: Without depressing the brake pedal (for Automatic Transmission) or clutch pedal (for Manual Transmission), turn the ignition switch to IG.

*3: Turn the ignition switch off and remove the key from the ignition key cylinder.




ACTIVE TEST


HINT:
·

Using the intelligent tester to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

·

If the ignition switch cannot be turned to ON, communication with the intelligent tester can be performed by connecting the intelligent tester to the vehicle and turning a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the intelligent tester and vehicle begins.



a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Immobiliser / Active Test.


e.

According to the display on the intelligent tester, perform the Active Test.

Body Electrical > Immobiliser > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Security Indicator Security indicator light ON/OFF The test is possible when the following condition is met:

The key is in the ignition key cylinder.