Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › THEFT DETERRENT SYSTEM
RM1880E _58 Vehicle Interior _013238 THEFT DETERRENT / KEYLESS ENTRY _0068616 THEFT DETERRENT SYSTEM J

THEFT DETERRENT / KEYLESS ENTRY  THEFT DETERRENT SYSTEM  Security Indicator Light Circuit  


DESCRIPTION

When the theft deterrent system is in the disarmed state, the security indicator light assembly will blink continuously if the engine immobiliser system is set, or not illuminate if the engine immobiliser system is not set.

When the theft deterrent system is in the armed state, the engine immobiliser system is automatically set and the security indicator light assembly will blink continuously.

When the theft deterrent system is in the arming preparation state or alarm sounding state, the theft warning ECU assembly causes the security indicator light assembly to illuminate.

WIRING DIAGRAM

B275966
4.969,1.737 5.393,1.916 0.424,0.179 10 G124 5.252,1.065 5.45,1.244 0.198,0.179 10 22 3.851,1.065 4.048,1.244 0.197,0.179 10 LP 2.428,1.065 2.558,1.244 0.13,0.179 10 E 4.146,1.065 4.268,1.244 0.122,0.179 10 2 2.248,1.065 2.371,1.244 0.122,0.179 10 1 5.526,1.153 5.82,1.332 0.294,0.179 10 IND 4.969,1.925 6.853,2.104 1.883,0.179 10 Theft Warning ECU Assembly 2.105,1.463 2.397,1.642 0.292,0.179 10 G27 2.105,1.651 4.242,1.83 2.137,0.179 10 Security Indicator Light Assembly

PROCEDURE

1.INSPECT SECURITY INDICATOR LIGHT ASSEMBLY
a.

b.
B275967
2.813,0.885 2.635,0.479 2.635,0.479 2.469,0.479 true 2.792,1.229 2.969,1.646 2.969,1.646 3.135,1.646 true 2.24,0.396 2.531,0.625 0.292,0.229 10 LP 3.167,1.563 3.385,1.802 0.219,0.24 10 E

Apply battery voltage between the terminals of the indicator, and check the illumination of the security indicator.

OK:
Measurement Condition Specified Condition
Battery positive (+) → Terminal 2 (LP)
Battery negative (-) → Terminal 1 (E)
Illuminates


NOTICE:
·

If the positive (+) lead and the negative (-) lead are incorrectly connected, the security indicator light assembly will not illuminate.

·

If the voltage is too low, the security indicator light assembly will not illuminate.




Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (SECURITY INDICATOR LIGHT - THEFT WARNING ECU AND BODY GROUND)

NG

2.CHECK HARNESS AND CONNECTOR (SECURITY INDICATOR LIGHT - THEFT WARNING ECU AND BODY GROUND)
a.

Disconnect the G27 security indicator light assembly connector.


b.

Disconnect the G124 theft warning ECU assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G27-2 (LP) - G124-22 (IND) Always Below 1 Ω
G27-2 (LP) or G124-22 (IND) - Body ground Always 10 kΩ or higher
G27-1 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR